Moog Videolarm PM3 Instruction sheet

Specification Catalog
Number Section
INSTRUCTIONS 5050 3
MODEL: Accessories
PM3
PRODUCT INSTRUCTIONS
STANDARD INSTALLATION PROCEDURE
INCLUDES MODELS: PM3
STANDARD ACCESSORIES (Supplied)
4 - Hex Head Bolts (3/8" - 16 x 2.0")
4 - Lock Washers (3/8")
4 - Nuts (3/8")
2 - Stainless Steel Straps
2 - Slide Buckle
PRECAUTIONS ON INSTALLATION
1. The pole mount adapter Model TC931PM3 is designed for
outdoor use, and mounting to a pole in conjunction with a
wall mount bracket.
2. The combined weight of camera, lens, housing, pan/tilt,
and
the wall mount bracket must not exceed 150 lbs. (67 kg).
3. Select a location where the combined weight of the brack-
et,
housing, pan/tilt and the wall mount bracket can be
properly supported.
DISCLAIMER
CAUTION: This unit must be properly and securely mounted
to
a supporting structure capable of sustaining the
weight of the bracket and camera assembly.
Accordingly:
1. The installation should be made by a qualified installer.
2. The installation should be in compliance with local codes.
3. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight the hardware will
be required to sustain.
INSTALLATION
1. Combine the WM bracket with the pole mount adapter and
firmly attach it with four hex head bolts lock washers and
nuts provided.
2525 Park Central Blvd. • Decatur, Ga 30035 • [phone] • 800-554-1124 U.S. & Canada • www.videolarm.com • Fax [phone]
2. Mount the bracket assembly to the pole by using the
stainless steel straps provided. (See banding instruc-
tions)
BANDING INSTRUCTIONS
1. Band may be used from bulk roll as this completely elimi-
nates waste of band. Slide buckle on band as shown,
bringing the end of band around object to be clamped
and again through buckle.
2. Continue band around object once more and again through
buckle. Double banding develops a great deal more
radial compression than single banding. Bend the end of
the band under buckle.
Band Gripper
Lever
Tool Nose
Slide
Te nsion handle
REVISION DATE: May 16, 2003

- 2 -
Roll Tool Over
Buckle
Tu rn handle Counterclockwise
for Back-off during Rollover
6. Pull cutting handle to cut the band.
7. Remove tool, holding stub of band down with thumb.
8. Clinch stub by hammering down buckle ears, completing
Band-It clamp.
3. Place band in the open slot of the tool nose and slide in.
With thumb on band gripper lever, apply tension by turn-
ing handle of tool. After tension is created, it is no longer
necessary to hold band gripper lever as it locks itself
under tension.
4. Place finger on Band-It Band at buckle while tensioning
with tool handle, When you feel Band-It Band stop moving
through buckle as you are turning handle, maximum pres-
sure is being exerted by the Band-It Band around object
being clamped. Stop turning handle.
5. Roll tool over buckle, backing off with tension handle
throughout entire rolling operation. Failure to back off
with tension handle throughout entire course of roll may
result in breaking of band. There is no loss of tension, as
band released is used up in the bend.
Handle Turned
Clockwise For
Tightening
Cutting handle
Hand-Schneidheble

!
Caution
Risk of
ElECtRiC shoCk!
Caution: to REDuCE thE Risk of
ElECtRiCal shoCk, Do not EXPosE
CoMPonEnts to WatER oR MoistuRE.
safEtY PRECautionsiMPoRtant safEGuaRDs
1. Read Instructions - All the safety and operating instructions should be read
before the unit is operated.
2. Retain Instructions -Thesafetyandoperating instructions should be retained
for future reference.
3. Heed Warnings - All warnings on the unit and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating & user instructions should be followed.
5. Electrical Connections - Only a qualified electrician should make electrical
connections.
6. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible distance.
8. Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit. Accordingly:
a. Installation should be made by a qualified installer.
b. Installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit,
taking into account both the composition of the mounting surface and
the weight of the unit. Be sure to periodically examine the unit and the
supporting structure to make sure that the integrity of the installation
is intact. Failure to comply with the foregoing could result in the unit
separating from the support structure and falling,with resultant damages
or injury to anyone or anything struck by the falling unit.
unPaCkinG
Unpack carefully. Electronic componentscan be damaged ifimproperlyhandled
or dropped. If an item appears to have been damaged in shipment,replace it
properly in its carton and notify the shipper. Be sure to save:
1. The shipping carton and packaging material. They are the safest material in
which to make future shipments of the equipment.
2. These Installation and Operating Instructions.
!
The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of non-insulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intendedtoalerttheusertopresenceofimportantoperating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
24 houR tEChniCal suPPoRt
1-800-554-1124
sERViCE
If the unit ever needs repair service,customer should contact Videolarm
(1-800-554-1124) for return authorization & shipping instructions.
tEChniCal suPPoRt
Videolarm has set-up a 24 hour technical support line for their customers.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:
PRODUCT CATEGORY PARTS LABOR
All Enclosures and Electronics Three (3) Years Three (3) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R.Illuminators Five (5) Years Five (5) Years
Controllers Three (3) Years Three (3) Years
Power Supplies Three (3) Years Three (3) Years
Accessory Brackets Three (3) Years Three (3) Years
During the labor warranty period, to repair the Product,Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc. Decatur GA.
The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials
Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support Team at 800.554.1124, extension 101.
Videolarm will return the repaired Product freight prepaid to Purchaser.Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty
period or at any time.After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice
with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.
If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm for the cost of investigating
the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire
Product.The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge,new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during
the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts of God (i.e.,hurricanes,
earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions,failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization,written in product instructions,or recommended in the service manual for the Product.
Furthermore,Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage)
and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the published environmental
and electrical parameters, or if such Product’s original identification (trademark, serial number) markings have been defaced,altered, or removed. Videolarm
excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind),except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES,VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.VIDEOLARM HEREBY DISCLAIMS
ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS
PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM,IF ANY,AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH
SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL,INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.