Morgan MSF-16P1 User manual

E-mail: [e-mail]
www.morgan.my
Market Expansion
Services by
www.dksh.com.my
facebook.com/morganappliances
USE MANUAL
Stand
Fan MSF-16P1
MSF-18P1
MSF-18P1(IM)101116_Layout 1 11/16/16 4:50 PM Page 1

3
1
2
34
56
7
8
9
10
11
PARTS IDENTIFICATION
SPECIFICATIONS
1. Front Grille
2. Spinner
3. Blade
4. Plastic Nut
5. Rear Grille
6. Motor
7. Control box
8. Inner pipe
9. Outer pipe
10. Round base
11. L Screw & Steady plate
MODEL MSF-16P1 MSF-18P1
ATED VOLTAGE / F EQUENCY 220-240V~ 50/60Hz
ATED WATTAGE 55W 85W
SIZE 40CM 46CM
C O N T E N T S
3
3
4
5
5
6
6
Parts Idenfication
Specifications
Safety Precautions
Assembly Instructions
Operation Instructions
Care & Cleaning
rouble Shooting
2
MSF-18P1(IM)101116_Layout 1 11/16/16 4:50 PM Page 2

4 5
ASSEMBLY INSTRUCTIONS
Thank you for purchasing another quality Morgan product. We seek to excel by
designing products with innovation, quality and safety of our customers in mind:
• Do not use outdoors. Your appliance is solely intended for household use only.
• Do not operate the appliance if power cord or power plug is damaged. It must be
replaced by the manufacturer or its service agent or a similarly qualified person in order
to avoid any hazards.
• Never leave the appliance within reach of children without supervision. he use of this
appliance by young children or the physically challenged must always be supervised.
• Unplug the fan before cleaning, transportation and after you have finished operating
the fan.
• Never immerse the appliance, the power cable or the power plug in water or in any
other liquids. Never spray liquids onto fan.
• Deformation or operational failure may occur when the appliance is used on unstable
surfaces or close to places with heating sources.
• Avoid contact with moving parts.
• Do not operate in the presence of explosives or flammable fumes.
NOTE
• Always ensure fan is properly fitted before use.
• he use of attachments not recommended by the manufacturer may be hazardous.
• Always use on a dry, flat surface.
• If appliance malfunctions or has been damaged in any manner, do not attempt to repair
this appliance yourself but return it to the agent for examination, repair or adjustment.
SAFETY PRECAUTIONS
ASSEMBLY OF BASE & PIPE
1. Insert the outer tube to the base and place the steady plate under the base using the
locking screws provided to tighten them as shown.
2. Unscrew the height adjustment knob and pull up the inner tube to adjust the height.
Ensure that the knob is fully tightened before proceeding.
3. Position the fan body as shown. Loosen the tightening screw on the fan body and
insert the fan body onto the compensation tube. Re-tighten the screw.
ASSEMBLY OF BLADES AND GRILLES
1. Unscrew the spinner clockwise and the plastic nut counter-clockwise. hen remove
the plastic sleeve around the motor shaft.
2. Set the rear grille In proper position with the handle facing upwards.
3. Screw on the plastic nut tightly to attach the fan grille.
4. Discard sleeve on shaft.
5. Slide the blade onto the shaft until it contacts the retaining pin.
6. Screw the spinner onto the motor shaft in a counter-clockwise direction.
7. Loosen the screw on the plastic ring with a screw driver. Mount the front grille (logo
place in the proper direction) with the rear grille and fasten the plastic ring.
OPERATING INSTRUCTIONS
1. Ensure switch is in the “OFF” position before plugging in the power plug.
2. Adjust fan speed by using the speed selector.
3. o change the angle of the fan, gently tilt the fan head upwards or downwards.
(CAUTION: Ensure that the fan is not in operation).
MSF-18P1(IM)101116_Layout 1 11/16/16 4:50 PM Page 3

6
TROUBLE SHOOTING
P OBLEM SOLUTION
No oscillation Check if oscillation knob is depressed
Not functioning Check power plug, ensure that power is switched on and
Speed selector is turned to either one of the three speeds.
Noisy Ensure that the fan blade is properly inserted into shaft pins.
Ensure that plastic nut for rear grille is tightened.
Ensure fan blade knob is securely tightened.
Ensure fan grille ring is securely tightened.
1. Unplug fan and remove the front guard.
2. Wipe blades using a soft, damp cloth. Allow to dry. If necessary, use a soft brush to
remove dust from tie guards.
3. Reassemble fan completely before use. he motor bearings are permanently sealed and
do not require additional lubrication.
CARE & CLEANING
7
MSF-18P1(IM)101116_Layout 1 11/16/16 4:50 PM Page 4