MorphoAccess SIGMA Series Manual

MorphoAccess® SIGMA Series
Simplified Setup Reference
NOTE: Please be sure to complete Steps 1-3 BEFORE connecting your MorphoAccess® SIGMA
Series terminals
STEP 1 | GET GROUNDED. Ensure the person performing the install is grounded in order to
prevent ESD (Electrostatic Discharge) damage to the SIGMA series terminal.
STEP 2 | SHUT-OFF THE POWER. Do NOT proceed with installation until electrical power has
been switched-off.
STEP 3 | CHECK THE WIRES. Identify the +12V and GND wires in two places: (1) Electrical power
source, and (2) SIGMA series terminal.
NOTE: Inversion of the +12V and GND wire will damage the product.
HOW TO IDENTIFY THE +12V AND GND CONNECTIONS ON SIGMA SERIES TERMINAL:
BACK
6
6
6
6
1
1
1
1
USB
µSD
1 Power Supply +12V
2 Power Ground
3 Switch 2
4 Switch 1
5 Digital Ground
6 Digital Ground
PoE

MorphoAccess® SIGMA Series
Simplified Setup Reference
BACK
STEP 4 | INSTALL THE COIN BATTERY.
Slide the CR1225 V3 Li-Ion coin battery,
positive (+) side up, into the slot,
positioned above the micro USB port.
USB
µSD
RJ45
Reset
Button
6
6
6
6
1
1
1
1
PoE
PoE
POSITIVE (+)
NEGATIVE (-)
3V
CR1225
+
Coin Battery
Slot

MorphoAccess® SIGMA Series
Simplified Setup Reference
STEP 5 | CHOOSE ONE POWER SOURCE (NOT BOTH): EXTERNAL 12V OR POWER-OVER-
ETHERNET. MorphoAccess® SIGMA Series terminals will only accept power from either PoE or
an external power supply, but not both simultaneously, nor in tandem.
STEP 6 | POWER THE SIGMA TERMINAL
For External Power: 12-24 Volts (regulated) 1 Amp and must comply with CEE/EEC
EN60950 standard. External power could be provided by a 12-Volt Wiegand power
supply. Minimum: 12V @ 1A. Refer to Step 3.
For PoE (Power over Ethernet): Install the PoE Board. Then, connect the PoE cable to
the RJ45 jack into the back of the SIGMA series terminal. See the diagram below.
Power-over-Ethernet (PoE) Board
NOTE: Pay special attention to the orientation of the pins on the PoE Board
PoE Pins

MorphoAccess® SIGMA Series
Simplified Setup Reference
Power-over-Ethernet (PoE) Connectors on the SIGMA series terminal
µSD
USB
RJ45
Reset
Button
6
6
6
6
1
1
1
1
PoE Connectors

MorphoAccess® SIGMA Series
Simplified Setup Reference
6A | Position the PoE Board with the PoE Pins pointing down, and facing the µSD slot
and RJ45 port on the SIGMA series terminal

MorphoAccess® SIGMA Series
Simplified Setup Reference
6B | Insert the PoE pins (on the PoE Board) into the PoE connectors (of the SIGMA
series terminal)

MorphoAccess® SIGMA Series
Simplified Setup Reference
6C | GENTLY push the PoE board down to secure the connections between the PoE
Pins and PoE connectors

MorphoAccess® SIGMA Series
Simplified Setup Reference
STEP 7 | CHANGE THE FIRST BOOT CONFIGURATION STORAGE TYPE TO PERMANENT THEN
REBOOT. Follow the step-by-step guide below:
NOTE: Do not skip this step. By default, the First Boot Configuration Storage Type is set to
Temporary. After setting the storage type to Permanent, the SIGMA terminal must reboot for
the changes to save.
7.1 | Press the DOWN ARROW to the First Boot Configuration Storage Type menu.
FIRST BOOT ASSISTANT will be the first menu to appear after powering the SIGMA
terminal.
DOWN ARROW

MorphoAccess® SIGMA Series
Simplified Setup Reference
7.2 | Press FIRST BOOT CONFIGURATION STORAGE TYPE to open this menu.
7.3 | Select PERMANENT to highlight this setting, then press the CHECK MARK button
to confirm the changes and to exit to the First Boot Assistant menu.
CHECK MARK
Press this button after
selecting Permanent

MorphoAccess® SIGMA Series
Simplified Setup Reference
7.4 | First Boot Assistant menu will be in view again. First Boot Configuration Storage
Type should be now set to Permanent. If NO, repeat Step 7.3.
7.5 | Press the CHECK MARK button to reboot the SIGMA terminal. After the reboot,
the SIGMA terminal can now configured.
CHECK MARK