Morphy Richards IB47008 User manual

wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
Mister Cappuccino 10 cup filter
coffee maker with heated frother
Please read and keep these instructions
GGeettttiinnggtthheebbeessttffrroommyyoouurrnneewwccooffffeeeemmaakkeerr......
WARNING: Hot water and steam
Safety first
Caution must be used when handling hot water, coffee or steam
Run water through your machine before first use
It is important to run water through your coffee maker in order to rinse the machine. You can also
run water through to warm your coffee machine.
Descale as appropriate for the hardness of the water in your area
It is important to descale as the performance of your coffee
maker may be impaired by limescale and other impurities in the water supply.
CCMM4477000088RReevv22
For replacement parts, help with using your Morphy Richards, problems
and lots more, contact us by phone or through our website.
UUKKHHeellpplliinnee::0088770000660022661100
RReeppllaacceemmeennttppaarrttss::0088770011667766664411
IIrreellaanndd11880000440099111199
47008 rev2 24/4/06 14:42 Page 1

22UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011557766664411IIrreellaannddHHeellpplliinnee11880000440099111199
IIMMPPOORRTTAANNTTSSAAFFEETTYY
IINNSSTTRRUUCCTTIIOONNSS
The use of any electrical
appliance requires the following
common sense safety rules.
Primarily there is danger of
injury or death and secondly
the danger of damage to the
appliance. These are indicated
in the text by the following two
conventions:
IMPORTANT: Damage to the
appliance! In addition we offer
the following safety advice.
LLooccaattiioonn
• Remove all the packaging and
retain for future reference.
• Ensure the coffee maker is
used on a firm, flat surface.
• Do not use the coffee maker
outdoors or in a bathroom.
• Do not place the coffee maker
on a highly polished wooden
surface as damage may occur
to the surface.
• Do not place the coffee maker
on or near hot surfaces such
as a hot plate or radiant rings
or near a naked flame.
• WARNING: Do not place the
coffee maker onto a metal tray
or metal surface whilst in use.
MMaaiinnsslleeaadd
• Do not let the mains lead hang
over the edge of the worktop
where a child could reach it.
• Do not let the lead run across
an open space e.g. between a
low socket and table.
• Do not let the lead run across a
cooker or other hot area which
might damage the cable.
• The mains lead should reach
from the socket to the base
unit without straining the
connections.
PPeerrssoonnaallssaaffeettyy
• Ensure the lid of the glass jug
is securely in place before
pouring.
• Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
• Do not fill above the capacity
mark of the water level gauge
marked on the jug.
• Do not use the glass jug in a
microwave.
• Milk should not be reheated,
only heat it when required.
• When heating milk, please use
stainless steel jug provided.
• Do not fill milk jug above the
MAX mark.
• Do not touch metal parts until
the unit has cooled..
CChhiillddrreenn
• Children do not understand the
dangers associated with
operating electrical appliances.
Never allow children to use this
appliance.
PPrroodduuccttssaaffeettyy
• Never use warm or hot water
to fill the water tank.
• Ensure the lid of the glass jug
is securely in place before
pouring.
• Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
• Do not place the glass jug on
the hot plate unless the lid is in
position.
• Do not fill above the capacity
mark of the water level gauge.
• Do not use the glass jug in a
microwave.
• Milk should not be reheated,
only heat it when required.
• When heating milk, please use
stainless steel jug provided.
• Do not fill milk jug above the
MAX mark.
• Do not adjust the coffee
strength once brewing is in
process.•
Do not overfill the water tank.
• The glass jug gets hot while
the machine is in use. Always
use with care.
• Make sure the mains lead does
not touch the hot parts of the
machine.
• Do not wind the mains lead
around the hot appliance or
store the appliance until it has
fully cooled down.
TTrreeaattiinnggssccaallddss
• Run cold water over the
affected area immediately. Do
not stop to remove clothing,
get medical help quickly.
OOtthheerrssaaffeettyy
ccoonnssiiddeerraattiioonnss
• Disconnect the coffee maker
from the mains supply when
filling, cleaning or not in use.
• When unplugging, turn any
control to ‘off’, then remove
plug from the wall outlet.
• Keep the outside of the coffee
maker area clean and dry at all
times.
• Do not touch hot surfaces.
Always use handles or knobs.
• Do not immerse the coffee
maker itself in water and
always ensure the electrical
connections are kept dry.
• Do not operate any appliance
with a damaged cord or plug or
after the appliance
malfunctions or has been
damaged in any manner. Ring
the helpline number for advice
on examination and repair.
• The use of attachments or
tools not recommended or sold
by Morphy Richards may
cause fire, electric shock or
injury.
47008 rev2 24/4/06 14:42 Page 2

33wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
• Do not use the coffee maker
for anything other than its
intended purpose.
EElleeccttrriiccaall
rreeqquuiirreemmeennttss
Check that the voltage on the
rating plate of your appliance
corresponds with your house
electricity supply which must
be A.C. (Alternating current).
If the socket outlets in your
home are not suitable for the
plug supplied with this
appliance the plug should be
removed and the appropriate
one fitted.
WARNING : The plug
removed from the mains
lead, if severed, must be
destroyed as a plug with a
bared flexible cord is
hazardous if engaged into a
live socket outlet.
Should the fuse in the 13 amp
plug require changing a 13
amp BS1362 fuse must be
fitted.
WARNING: This appliance
must be earthed.
⁄
¤
‹
›
fi
fl
‡
·
‚
„
Â
‰
Ê
Á
Ë
È
FFeeaattuurreess
⁄Filter locating tab
¤Removable permanent mesh
filter
‹Removable filter holder with
locking tab
›Non drip valve
fiMilk frother on/off button
flMilk frother attachment
‡Milk frother hot plate
·Milk frother hot plate on/off
switch with indicator
‚Coffee hot plate on/off switch
with power & ready indicators
„Coffee hot plate
‰Water level indicator
ÂHinged reservoir lid with
strength selector.
ÊJug lid
ÁGlass coffee jug with water
level indicator
ËMeasuring spoon
ÈMilk frother jug
47008 rev2 24/4/06 14:42 Page 3

44UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011557766664411IIrreellaannddHHeellpplliinnee1188000044009911119944
OOPPEERRAATTIINNGGTTHHEE
AAPPPPLLIIAANNCCEE
BBeeffoorreeuussee
Take your coffee maker out of the
box and remove the packaging.
Before using the appliance for the
first time, clean thoroughly by
operating two or three times with the
maximum volume of fresh water (10
cups) but without using coffee.
Wash the detachable parts of the
machine in warm soapy water.
LLooccaattiinnggtthheeffiilltteerr
1To remove the filter, slide the locking
tab on the removable filter holder to
the unlock position and lift both the
holder and mesh filter out to clean.
(see cleaning) A
2To refit, place the removable filter
holder into the top of your coffee
maker, making sure the tab lines up
with the rib then slide the locking tab
to the lock position. Place the
permanent mesh filter inside the filter
holder by lining up the locating tab
with the groove in the filter holder as
shown
MMaakkiinnggccooffffeeee
1Lift up the hinged reservoir lid.
2Fill the water reservoir with the
required amount of water using the
water level indicator as a guide. Both
the jug and water level indicator are
marked in cups. Do not exceed the
maximum level on the water
gauge.B
3Spoon the required amount of
ground filter coffee into the mesh
filter spreading it evenly. We suggest
one level measuring spoon for every
cup. Ensure the filter is sitting
properly in the filter holder.
4Close the reservoir lid.
5Select the strength of coffee required
using the strength selector on the
reservoir lid.
6Slide the jug into the coffee maker
ensuring it sits correctly on the hot
plate. The jug lid must be in place
during the brewing process,
otherwise the non-drip valve will not
open, causing the filter to flood.
7Plug the filter coffee maker in at the
wall socket and push the coffee
on/off switch to ‘ON’ position. The
orange light will glow to show coffee
maker is working.
8Hot water will start to flow through
the coffee grounds and into the glass
jug as coffee.
9When the filtering process is
complete remove the glass jug from
your coffee maker and pour the
coffee into your cups.
10 The anti-drip valve will prevent any
remaining coffee dripping onto the
hot plate. Ensure that the jug is
replaced on the hot plate after
serving. While the coffee maker is
switched ON the hot plate will keep
the coffee warm.
11 Switch off the coffee maker when the
jug is empty or the coffee is no
longer required.
WARNING: The coffee maker and
hot plates are hot and remain hot
for some time after switching off.
12 Allow unit to cool.
13 Remove the permanent mesh filter
and empty the used coffee grounds.
Wash the filter immediately and dry
thoroughly. NOTE: THE MESH WILL
BECOME DISCOLOURED AFTER A
WHILE DUE TO THE STAINING
EFFECT OF COFFEE.
NOTE: It is normal for the green
ready light to go out and come back
on intermittently due to thermostatic
cycling.
B
Rib
Locking tab
A
47008 rev2 24/4/06 14:42 Page 4

5555
MMaakkiinnggaaccaappppuucccciinnoo
Prepare your machine as described
in the section ‘Making a coffee’. Use
your glass jug for measuring the
correct amount of water needed.
FFrrootthhiinnggmmiillkk
It is advised to start heating your
milk at the same time as heating
your coffee or several minutes before
making coffee to ensure milk is hot.
1Fill the stainless steel milk jug
provided with the required amount of
milk. Do not exceed the maximum
level or add less than the minimum
level.
2Place the jug on the hot plate and
switch on. C
NOTE: You can turn on the hot plate
at the same time as the coffee
hotplate. It will take approximately 5-
7 minutes for the milk to heat up to
its optimum frothing temperature.
3Lift the milk jug up to the milk frother
blade D. Raise the milk jug ensuring
that the cowl is just under the
surface of the milk - this will give the
maximum froth. Maintain the milk jug
in this position between 30-60
seconds.
WARNING: Take care as the milk
will be hot.
4Place the milk jug back on the hot
plate to reheat the milk and preserve
the quality of the froth.
NOTE: The jug can stay on the hot
plate until the coffee has finished
brewing but be careful not to burn
your milk/froth.
5Pour the coffee into cups and gently
pour or preferably spoon the milk
onto the coffee, then sprinkle a little
chocolate powder for the perfect
cappuccino.
6Turn off the milk frother hot plate by
pressing the on/off switch.
WARNING: the stainless steel jug
and the hotplate will remain hot
for sometime after switching off.
CClleeaanniinngg
The milk frother blade can be wiped
clean still attached to the machine or
it can be removed for easy cleaning
by unscrewing the blade and shaft.
Wash carefully in hot soapy water.
For quick cleaning just after use, fill
up the milk jug with hot water and
run the frother for 30-50 seconds;
repeat the process twice.
If the milk has been left for a long
time the cowl and blade can be
removed and soaked in hot soapy
water for 2-5 minutes before rinsing
clean.
1Remove the cowl directly after use
and rinse in warm water. EIt is
recommended that you clean the
blade immediately after use, as dried
milk can be difficult to remove.
The frother blade can be wiped clean
still attached to the machine.
2If further cleaning is required the
propeller and shaft can be removed.
To replace, insert the stem of the
milk frother blade into the mounting
hole on the unit and screw into
place.F
NOTE: If the blade is removed,
ensure that it is fully tightened in
place otherwise the frother will not
operate properly.
3There may be some splash back of
milk on the underside of the frothing
unit. Switch the unit off then simply
wipe this area clean with a damp
cloth.
WARNING: THE FROTHER ONLY
OPERATES CORRECTLY WHEN
THE COWLING IS CORRECTLY
ASSEMBLED.
DO NOT OPERATE THE FROTHER
DRY OR NOT SUBMERSED IN
LIQUID FOR LONG PERIODS OF
TIME.
E
F
D
C
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
47008 rev2 24/4/06 14:42 Page 5

66UUKKHHeellpplliinnee0088770000660022661144RReeppllaacceemmeennttPPaarrttss0088770011557766664455IIrreellaannddHHeellpplliinnee1188000044009911119966
RREECCIIPPIIEESS
Cappuccino
1/3 coffee
1/3 hot milk
1/3 hot frothed milk
Chocolate powder for sprinkling
1Prepare coffee as per ‘making a
coffee’ instructions.
2Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx. 5-7 minutes to
reach the appropriate temperature.
3Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 30-
60 seconds to froth.
4Pour the coffee in first and then the
hot milk into a cappuccino cup,
spoon over frothed milk.
5Sprinkle with chocolate powder to
serve.
Cafe Latte
1/2 coffee
1/2 hot frothed milk
1Prepare coffee as per ‘making a
coffee’ instructions.
2Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx. 5-7 minutes to
reach the appropriate temperature.
3Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 30-
60 seconds to froth.
4Pour the coffee into a tall glass and
top with the frothed milk.
Moccacino
1/3 coffee
1/3 hot frothed milk
1/3 hot chocolate
1Prepare coffee as per ‘making a
coffee’ instructions.
2Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx.5-7 minutes to reach
the appropriate temperature.
3Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 30-
60 seconds to froth.
4Prepare the hot chocolate according
to the instructions.
5Pour the coffee, hot milk and hot
chocolate into a tall glass and serve.
Irish coffee
Makes 2 servings
40ml of double cream
2 tsp sugar
4 shots of Irish whisky
350ml hot strong coffee
1Whip double cream until thick then
chill.
2Warm 2 Irish coffee glasses with hot
water and place in each a teaspoon
of sugar and 2 shots of Irish whisky.
3Divide coffee among the glasses.
4Slowly dribble the chilled cream over
the back of the spoon.
5Do not stir.
Amaretto coffee
250ml hot strong coffee
2 tablespoons of double or whipped
cream
2 shots of Amaretto
Sugar to taste
1Stir the coffee and alcohol together
either with a couple of tablespoons
of double-cream, or top with a dollop
of whipped cream.
2Sprinkle with grated chocolate and
serve.
47008 rev2 24/4/06 14:42 Page 6

77wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm77
HHIINNTTSSAANNDDTTIIPPSS
CCLLEEAANNIINNGGAANNDD
MMAAIINNTTEENNAANNCCEE
RReeffiilllliinngg
1Switch off the coffee maker, and
allow 5 minutes to cool.
2Lift the hinged reservoir and refill
with cold water.
DDeessccaalliinngg
• If you live in a harder water area, we
recommend that your coffee maker
is descaled at regular intervals, eg.
every 2 - 3 months. In areas of
moderately hard water you should
descale every 6 months.
• If the water filters through more
slowly than usual, it is a sign that
descaling is necessary.
• We recommend you to use
proprietary liquid descaler which is
especially made for coffee makers
and plastic kettles. Follow the
instructions on the bottle or sachet,
and them operate the coffee maker
with just water 3 times before
making coffee.
• Do not use kettle descaler unless the
packet specially states it is suitable
for coffee makers.
NOTE: The permanent mesh filter
should not be used during descaling.
CClleeaanniinnggccaarree
Unplug The coffee maker, and allow
to cool.
Do not immerse the coffee maker in
liquid.
Rinse the water tank occasionally
with cold water. Do not use a cloth
as any residue or lint left behind
may clog the coffee maker.
Remove the permanent filter discard
used coffee and wash with warm
soapy water. Extended soaking helps
remove coffee stains from the mesh.
Rinse and dry thoroughly.
Wash the milk frother blade,milk
frother attachment, milk frother jug,
glass jug, and filter holder, in warm
soapy water. Rinse and dry all parts
thoroughly. Refit filter, filer holder,
milk frother blade, and milk frother
attachment.
Wipe all external surfaces with a
damp cloth and dry thoroughly.
Care must be taken to ensure the
non drip valve situated on the
bottom of the filter holder is not
damaged during cleaning.
Never use harsh or abrasive
cleaners.
MILK FROTHER PARTS
(EXCLUDING MILK FROTHER JUG)
ARE DISHWASHER SAFE.
HHeellpplliinnee
If you have any difficulty with your
appliance, do not hesitate to call. We
are more likely to be able to help
than the store from where you
bought it.
Please have the following
information ready to enable our staff
to deal with your enquiry quickly:
• Name of the product
• Model number as shown on the
underside of the appliance.
• Serial number as shown on
underside of the appliance.
For electrical products sold within
the European Community.
At the electrical products useful life it
should not be disposed of with
household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
UK Helpline 0870 060 210
Replacement Parts 0870 167 6641
Ireland Helpline 1800 409119
47008 rev2 24/4/06 14:42 Page 7

8888
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
YYOOUURRTTWWOOYYEEAARR
GGUUAARRAANNTTEEEE
It is important to retain the retailers
receipt as proof of purchase. Staple
your receipt to this back cover for
future reference.
Please quote the following
information if the product develops a
fault. These numbers can be found
on the base of the product.
Model no. Serial no.
All Morphy Richards products are
individually tested before leaving the
factory. In the unlikely event of any
appliance proving to be faulty within
28 days of purchase it should be
returned to the place of purchase for
it to be replaced.
If the fault develops after 28 days
and within 24 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy Richards
at the address shown.
You will be asked to return the
product (in secure, adequate
packaging) to the address below
along with a copy of proof of
purchase.
Subject to the exclusions set out
below (see Exclusions) the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.If for
any reason this item is replaced
during the 2 year guarantee period,
the guarantee on the new item will
be calculated from original purchase
date. Therefore it is vital to retain
your original till receipt or invoice to
indicate the date of initial purchase.
To qualify for the 2 year guarantee
the appliance must have been used
according to the manufacturers
instructions. For example coffee
makers should have been regularly
descaled.
EXCLUSIONS
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
1The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturers
recommendations or where the fault
has been caused by power surges or
damage caused in transit.
2The appliance has been used on a
voltage supply other than that
stamped on the products.
3Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
4Where the appliance has been used
for hire purposes or non domestic
use.
5Morphy Richards are not liable to
carry out any type of servicing work,
under the guarantee.
6Plastic filters for all Morphy Richards
kettles and coffee makers are not
covered by the guarantee.
• This guarantee does not confer any
rights other than those expressly set
out above and does not cover any
claims for consequential loss or
damage. This guarantee is offered as
an additional benefit and does not
affect your statutory rights as a
consumer.
• This guarantee is valid in the UK and
Ireland only.
For electrical products sold
within the European
Community. At the end of the
electrical products useful life it
should not be disposed of
with household waste.
Please recycle where facilities
exist. Check with your Local
Authority or retailer for
recycling advice in your
country.
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of its
models at any time.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Helpline (office hours)
UK 0870 060 2610
Republic of Ireland 1800 409119
CCMM4477000088RReevv220044//0066
FFoorrddeettaaiillssooffootthheerrpprroodduuccttssiinntthheeMMoorrpphhyyRRiicchhaarrddssrraannggeepplleeaasseesseeeeoouurrwweebbssiittee......
47008 rev2 24/4/06 14:42 Page 8