Mosa DP2500iL User manual

STATION
POWER
OWNER'S MANUAL
DPiL Series
PORTABLE
DP1000iL / DP1500iL / DP2000iL / DP2500iL
VER2.3-20220420

CONTENT
1. UNIT DESCRIPTION ................................................................................- 3 -
1.1 COMPONENTS IDENTIFICATION .................................................- 3 -
1.2 OUTPUT PANEL .............................................................................- 4 -
1.3 CHARGING INPUT PANEL.............................................................- 7 -
1.4 BATTERY CONNECTOR ................................................................ - 8 -
2. CHARGING THE POWER STATION........................................................- 8 -
2.1 PV CHARGING INPUT ...................................................................- 9 -
2.2 AC CHARGING INPUT ................................................................. - 11 -
2.3 DC CHARGING INPUT.................................................................- 12 -
2.4 WIND CHARGING INPUT (optional) ............................................- 12 -
2.5 DC QUICK CHARGING INPUT (optional) ....................................- 14 -
3. OPERATING THE POWER STATION ....................................................- 15 -
3.1 DC OPERATION ...........................................................................- 16 -
3.2 AC OPERATION............................................................................- 17 -
4. LCD DISPLAY .........................................................................................- 19 -
5. CONNECT THE EXTERNAL BATTERY .................................................- 22 -
6. REPLACE THE BATTERY ......................................................................- 23 -
6.1 REMOVE THE BATTERY .............................................................- 23 -
6.2 INSTALL THE BATTERY...............................................................- 25 -
6.2.1 BIND THE BATTERY.....................................................‐  25‐
6.2.2 REINSTALL THE BATTERY INTO THE POWER
STATION....................................................................................‐  26‐
6.2.3 CONNECT THE BATTERY...........................................‐  27‐
7. TRANSPORTATION AND STORAGE.....................................................- 28 -
8. PROTECTION.........................................................................................- 29 -
8.1 INPUT PROTECTION...................................................................- 29 -
8.2 OUTPUT PROTECTION...............................................................- 29 -
9. TROUBLE SHOOTING ...........................................................................- 31 -
10. SPECIFICATIONS.................................................................................- 34 -

‐2‐
INTRODUCTION
Congratulations on your selection of a marvelous power station.
This manual will provide you with a good basic understanding of
the safe operation and maintenance of this machine, please read it
carefully.


Read this manual carefully before operating this power station.
This manual should stay with this power station if it is sold.
The power station is a potential source of electrical shock if
misused. Do not expose the power station to moisture, rain or
snow. Do not let the power station get wet, and do not operate
it with wet hands.
There is high-voltage power inside the power station. Do not
start the power station when the casing is open to prevent
accidental electrical shock.
Electrical equipment (including lines and plug connections)
should not be defective.
Do not connect to a building electrical system unless an
isolation switch has been installed by a qualified electrician.
Place the power station in a place where pedestrians, children
and pets are not likely to touch. Do not let children operate the
power station without supervision. Protect children by keeping
them at a safe distance from the generating set.
Keep this owner’s manual handy, so you can refer to it at
any
t im e. We reserve the right to modify this product or
manual at any time without any notice.
We continually seek advancements in product design and
quality. Therefore, while this manual is the newest, there may
be slight difference between your power station and this
manual.
If you have any questions, please consult an authorized dealer.

‐3‐
Please DO NOT modify the unit in any way, otherwise factory
may reserve the right not to provide the complete warranty.
1. UNIT DESCRIPTION
1.1 COMPONENTS IDENTIFICATION
(1). Output Panel: Location of power station controls and output
receptacles.
(2). Charging Input Panel: Location of power station charging input
receptacles.
(3). Maintenance Cover: Remove the cover to install or replace battery
in the power station.
(4). Carrying Handle: Lift the power station by this handle.
(5). Draw Bar Handle: Pull the handle to wheel this power station
around.
7
3
1
2
6
5 4 6
2

‐4‐
(6). Front Handle / Rear Handle: Two persons can carry the power
station easily by these two handles.
(7). Connector Cover: Open the cover to connect the Battery.
Connector before charging or operating the power station.
1.2 OUTPUT PANEL
1 2
4
10 7
14
15
16
3
11 12 13
9
6
5

‐5‐
(1). AC Switch: This switch turns ON or OFF AC output of the power
station.
(2). AC Receptacle: AC output receptacles for connecting AC devices.
(3). Main Switch: This switch turns ON or OFF DC output of the power
station, and AC Switch is available only after the main switch is turned
on.
(4). Cigarette Lighter Receptacle: the 12V DC output receptacle for
cigarette lighter plugs.
(5). USB Receptacle: the 5V DC output receptacle for USB plugs.
(6). Type-C Receptacle: the PD60W DC output receptacle for Type-C
plugs.
(7). USB Receptacle: the QC3.0 DC output receptacle for USB plugs.
1
3
5
14
15
16
2 12
4
8
11
10
13
6 7

‐6‐
(8). 5.5mm Port: the 12V DC output receptacle for 5.5mm plugs.
(9). 6mm Port: the 12V DC output receptacle for 6mm plugs.
(10). LCD Display: Display remaining capacity of the battery,
input/output watts, remaining operation hours or charging hours of the
battery, battery voltage, total running time, andfault warnings. When
the power station is charging, the battery segments in the LCD screen
will blink. The power station is fully charged when all battery segments
stop blinking and remain solid.
(11). Display button ▲: You can activate the display backlight or value
displayfor remaining capacity of the battery by pressing the button
once, and for total running time by pressing the button twice.
(12). Display button ▼: You can activate the display backlight or value
display for battery voltage by pressing the button.
(13). Display button S: You can activate the display backlight by
pressing the button, and the factory orauthorized dealer can use this
button to initialize the LCD Display.
(14). Ready LED: the Ready LED light comes ON when the AC output
is ready.
(15). Warning LED: The light comes ON and flashes when the following
problems occur:
AC output is overloaded.
AC output is short-circuited.
AC output is under voltage.
AC output is over voltage.
Over temperature in the inverter.
Battery is under voltage.
Battery is over voltage.
(16). Over Temperature LED: The light comes ON and flashes when
the temperature in the power station is too high.

‐7‐
1.3 CHARGING INPUT PANEL
(1). PV Charging Input: Charge the power station from solar panels
(optional equipment).
(2). DC Charging Input: Charge the power station from cars.
(3). AC Charging Input: Charge the power station from wall outlets or
other AC power source.
(4). Wind Charging Input (optional): Charge the power station from
wind turbines (optional equipment).
(5). DC Quick Charging Input (optional): Charge the power station from
DC 24V power unit (optional equipment).
1 32
4
5

‐8‐
1.4 BATTERY CONNECTOR
 
You need to connect the battery connector 2 before charging or
using the power station:
(1). Open the connector cover 1.
(2). Connect the battery connector 2 securely together with the
connector 3 of the power station, otherwise the power station cannot be
charged or used.
2. CHARGING THE POWER STATION
NOTE
Before using for the first time, or after long-term storage,
please charge the power station fully from AC charging for at
least 10 hours tocalibrate the battery capacity of the power
station.
During storage, please make sure to charge the power station
at least every six (6) months.
When the power station is charging, the battery segments in
the LCD screen will blink.
1
2
3

‐9‐
The power station is fully charged when all battery segments
in the LCD screen stop blinking and remain solid.
2.1 PV CHARGING INPUT
Loosen
1
2
4
3
3
5

‐10‐
You can charge the power station from solar panels as follows:
(1). Remove the cover 1 from PV charging port 2.
(2). Connect PV charging port 2 to MC4 port 5 of solar panels 4
(optional equipment) by PV charging cable 3, which can be found in the
packing box.
NOTE
You can charge the power station quickly from several solar
panels in series if the solar panel power is small. But the total
voltage of the solar panels in series CAN NOT exceed the PV
INPUT voltage range.
4
3
5

‐11‐
2.2 AC CHARGING INPUT
You can charge the power station from wall outlets or other AC
source as follows:
Connect AC charging port 1 to wall outlets or other AC source by the
AC charging cable 2, which can be found in the packing box.
NOTE
The voltage of the AC charging CAN NOT exceed the AC
INPUT voltage range.
Before using for the first time, or after long-term storage,
please charge the power station fully from AC charging for at
least 10 hours tocalibrate the battery capacity of the power
station.
1
2

‐12‐
2.3 DC CHARGING INPUT
You can charge the power station from cars as follows:
Connect DC charging port 1 to cigarette lighter receptacle of 12V or
24V cars by DC charging cable 2, which can be found in the packing
box.
NOTE
The car engine must run when charging the power station from
the car.
2.4 WIND CHARGING INPUT (optional)
1
2
1
2
3
Loosen

‐13‐
You can charge the power station from wind turbines as follows:
(1). Remove the cover 1 from wind charging port 2.
(2). Connect wind charging port 2 to wind charging cable 4 of wind
turbines (optional equipment) by wind charging plug 3, which can be
found in the packing box.
NOTE
The voltage of the wind turbine CAN NOT exceed the WIND INPUT
voltage range.
4
3
2

‐14‐
2.5 DC QUICK CHARGING INPUT (optional)
You can charge the power station from DC 24V power unit as
follows:
(1).Unscrew the screw 1, and then open the cover 2.
(2). Connect DC quick charging port 3 to DC quick charging cable 5 of
DC 24V power unit (optional equipment) by DC quick charging plug 4,
which can be found in the packing box.
Loosen
1
3
2
2
1
3
4
5

‐15‐
NOTE
The voltage of the DC power unit CAN NOT exceed the DC
QUICK INPUT voltage range.
DO NOT short circuit the DC quick charging port 3!
3. OPERATING THE POWER STATION
1 2
4
10 7
14
15
3
9
6
5

‐16‐
3.1 DC OPERATION
You can use the DC output from the power station as follows:
(1). Push the main switch 3 to "ON" position.
(2). Receptacle 4, 8 and 9 all are 12V DC output port, according to the
plug type of 12V DC electric devices to choose suitable one to connect.
(3). Receptacle 5, 6 and 7 all are DC output ports for USB or Type-C
plugs. The maximum output power of the Type-C 6 is 60W, and the
maximum output power of the USB 7 is 18W. These receptacles can
automatically identify electric devices and then select the corresponding
voltage and current for power supply.
1
3
5
14
15
2
4
8
10
67

‐17‐
NOTE
Be sure the receptacle load current is within receptacle rated
current.
If the DC output is overloaded (in excess of rated current), or if
there is a short circuit in a connected appliance, the icon
and icon in LCD Display 10 will show（as shown in the
figure below）, and the DC output to the connected appliance(s)
will shut off.
3.2 AC OPERATION
You can use the AC output from the power station as follows:
(1). Push the main switch 3 to "ON" position.
(2). Push the AC switch 1 to "ON" position.
(3). Make sure the ready LED 14 comes on.
(4). Connect plug to the AC receptacle 2 for AC electric devices.
NOTE
If the power station is equipped with Gen-mate unit (optional
equipment), the AC output also canbe switched on or off by Gen-
mate APP in smartphones except for above step 2 as follows:

‐18‐
AC output voltage is very high, operators must be protected
from electric shock at all times.
Do not operate with wet hand.
Do not operate by children without supervision.
Do not expose the power station to rain, moisture or snow.
NOTE
Be sure all electric devices including the lines and plug
connections are in good condition before connection to the
power station.
Be sure the total AC load is within the power station rated
output.
The rated and maximum output power of the power station is
based on resistive load, and is not applicable to inductive load
and capacitive load. Since the power factor of inductive load
and capacitive load are less than 1, the rated power of inductive
load and capacitive load shall be small enough compared with
the rated power of the power station, and the ratio of the two
shall not exceed the power factor of the load, otherwise the
power station may be overloaded or damaged. For example, if
the power factor of the inductive load is 0.6, and if the rated
output power of the power station is 2000VA, the rated power
of this load cannot exceed: 0.6 * 2 = 1.2kW, otherwise the power
station may have overload protection or damage.

‐19‐
If the AC output is overloaded (in excess of rated power), or if
there is a short circuit in a connected appliance, the warning
LED 15 will go ON, and the AC output to the connected
appliance(s) will shut off.
4. LCD DISPLAY
You can activate the display backlight by pressing any of the three
buttons ▲/▼/S. The built-in LCD Display can indicate some important
information:
Battery icon: When the power station is charging, the battery
segments in the LCD screen will blink. The power station is fully
charged when all battery segments stop blinking and remain
solid. If the remaining capacity of the battery it too low, the battery
segments become blank and will blink as a prompt of recharging.