Motolux 802311012 Installation manual

Australian owned
Australian designed
61 (0)3 9876 0400
www.motolux.com.au
Ordering Information
Australia / New Zealand
1. Pairing the motor to the remote: Start by selecting the channel that you want to pair the motor with on the remote control.
Next
Insert Paper Clip in Hole of Motor for approx. 1 second and the motor will give a jiggle, then on the Remote push the
Up Button.
The motor will jiggle to indicate that it is paired.
2. Check the Direction: If the direction is correct there is no action required move to step 3.
If the direction is wrong, Push and hold the Stop Button until you get a Jiggle from the motor then push the Down Button.
Test the blind and the direction should be correct.
3. Limit Setting: TOP LIMIT FIRST
Push and hold the button in the Setting Hole on the remote with a Paper Clip until you get a jiggle – now move the blind to
where you would like the Top Limit to be – now push and hold the button in the Setting Hole on the remote, you will get a jiggle
Next
Move the blind to where you would like the Bottom Limit to be – now push and hold the button in the Setting Hole on the
remote, you will get a jiggle.
Next (very important)
Push and hold the button in the Setting Hole on the remote, you will get a jiggle. This has now recorded the limits, please test
the blind.
The above will need to be done for Each Different Motor on Each Different Channel.
1. On the Remote go to Blind 1 on Channel 1 – Push and Hold the Stop Button until you get a jiggle. Now go to Channel 6 and
push and hold the Up Button you will get a Jiggle. Blind 1 is now added to Channel 6.
2. On the Remote go to Blind 2 on Channel 2 – Push and Hold the Stop Button until you get a jiggle. Now go to Channel 6 and
push and hold the Up Button you will get a jiggle. Blind 2 is now added to Channel 6.
Repeat these steps until you have moved all blinds over to channel 6.
This feature can also be used to transfer motors onto other Remote Controls.
Simple Programming
Resetting a Motor Back to Factory
To Add Multiple Blinds to a Group Channel
PROGRAMMING INSTRUCTIONS 1/2
Firstly you will need something small enough to put in the both the hole in the head of the motor and in the setting hole on
the remote control, a Paper Clip or Jewelers Screwdriver is perfect.
Firstly plug the charger into the small white cable on the end of the motor, plug the charger into a power point and switch
on the power. You will notice the light will turn red on the wall charger, when the light turns green the motor has been fully
charged.
There is a low battery indicator built into the motor, this will start beeping when the motor needs to be recharged. Please let
your customers know that when the motor starts beeping it needs to be recharged before it can be used again.
Should you need to reset a motor back to Factory Settings you will need to push the button inside the hole in the Head of
the Motor Five Times in quick succession holding the button in on the Fifth Push, you will get a Double Jiggle indicating the
motor has been reset and all Limits and Pairing have been deleted.
Example: Putting 5 blinds all on Channel Six.
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 2 - 2021
25mm DC RECHARGEABLE BATTERY 1.0NmMOTOR - 802311012 (MT25-1/30-ES-E)

Australian owned
Australian designed
61 (0)3 9876 0400
www.motolux.com.au
Ordering Information
Australia / New Zealand
PROGRAMMING INSTRUCTIONS 2/2
The above are simple programming steps but there are more functions this motor can perform.
Motolux Battery Motors have a low power feature that greatly extends battery life, due to this feature it is required that
when operating a slightly longer press of the buttons on the remote is required (approximately 1 second push), by doing
this the receiver in the motor is woken up and the blind will operate as normal.
1. Intermediate Limits: Other than the Top and Bottom Limits this motor can store an additional four Intermediate Limits. To set
Intermediate Limits: After setting the top and bottom limits and exiting the program mode, move the blind to where you would
like an intermediate limit set. Press the button in the setting hole in the back of the remote control until you get a jiggle now
press the button in the setting hole on the back of the remote a second time, you will get a jiggle. An intermediate limit has now
been set.
When operating the blind if you do not want to stop at the intermediate limit: Press the button for the direction that you
would like the blind to move in, once the blind starts moving press the same button a second time and it will skip that limit and
continue onto the furthest limit.
2. Adjusting a Limit after it has been set: Move the blind to the limit that you wish to adjust, press the button in the setting
hole on the back of the remote until you get a jiggle, now move the blind to the new limit position and press the button in
the setting hole on the back of the remote; the blind will jiggle and the limit has been adjusted.
3. To delete an Intermediate Limit or Bottom Limit (Top limit cannot be deleted in this manner): Move to the limit that
you wish to delete, push the button in the setting hole on the back of the remote and keeping the button pushed in, the
blind will jiggle once and then a second time approximately 5 seconds later indicating that the limit has been deleted.
Additional Features
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 2 - 2021
25mm DC RECHARGEABLE BATTERY 1.0NmMOTOR - 802311012 (MT25-1/30-ES-E)
This manual suits for next models
1
Table of contents
Other Motolux Engine manuals
Popular Engine manuals by other brands

Stobag
Stobag MOVENO Tandem DWIR-E Instructions and warnings for installation and use

Briggs & Stratton
Briggs & Stratton 310000 VERTICAL SERIES Operator's manual

Parker
Parker P1D Series manual

Diamond Products
Diamond Products CB733 Operator's manual & parts

Toyota
Toyota 1981 2F Repair manual

ABB
ABB AMXE132 manual