Motorline professional AC-6001P Instruction Manual

V1.0
REV.062022
ROLLING600-800-1000ROLLING600-800-1000
EN
USER/INSTALLER MANUAL

1A 1B
1B
4A
4A
4B
4B
5A
5A
5B
5B
6A
6A
6B
7
8
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
íNDICE
STANDARDS TO FOLLOW
SECURITY INFORMATION
INSIDE THE PACKAGE
TECHNICAL DRAWING
TECHNICAL CHARACTERISTICS
CONNECTION TO SWITCH OR CONTROL BOARD
TROUBLESHOOTING
INSTALLING THE MOTOR ON THE LEFT SIDE
GEAR BRACKET
SQUARE PLATE BRACKET
BEARING INSTALLATION
INSTALLATION OF THE GEAR
LIMIT SWITCHES ADJUSTMENT
CHAIN
01. SAFETY INSTRUCTIONS
02. INFORMATION
03. PACKAGE
05. CONNECTION SCHEME
06. MAINTENANCE
04. INSTALLATION AND ADJUSTMENTS
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where
they purchased this product or the National Environment
Agency for details on where and how they can take these
items for environmentally safe recycling. Business users
should contact their vendor and check the terms and
conditions of the purchase agreement. This product and
its electronic accessories should not be mixed with other
commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.
ATTENTION:

2EN
01. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk causing
serious injuries.
•This manual is intended firstly for specialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Donotuse the product ifit is necessary repairoradjustmentisrequired.
•When performing maintenance, cleaning and replacement of parts, the
product must be disconnected from power supply. Also including any
operation that requires opening the product cover.
•The use,cleaning and maintenance ofthis product maybecarriedout by
any persons aged eight years old and over and persons whose physical,
sensorial or mental capacities are lower, or by persons without any
knowledge of the product, provided that these are supervision and
instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation of
the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points to
ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The central must be installed on a safe place of any fluid (rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the power
supply cable. Please note that all the cables must enter the central
from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
•Attach the permanent label for the manual release as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical

3EN
01. SAFETY INSTRUCTIONS
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or 110Vac,
ensure that connection is to an electrical panel with ground connection.
•The product is only powered by low voltage satefy with central (only at
24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation use
or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
MOTORLINE ELECTROCELOS SA.
Travessa do Sobreiro, nº29
4755-474 Rio Côvo (Santa Eugénia)
Barcelos, Portugal
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information

4A 4B
1
7
8
65
3
4
2
9
ENEN
02. INFORMATION 03. PACKAGE
SECURITY INFORMATION INSIDE THE PACKAGE
Carefully read and follow all safety instructions and warnings before installing and using the
Door. Incorrect installation may cause damage.
• The Door must be installed by a qualified technician; otherwise it may cause malfunction and
damage.
• All users must be notified that they must not use the Door without being in sight.
• Keep the remote controls away from children, in order to prevent the door from being
unintentionally activated.
• Before any technical intervention, the electricity must be cut off.
• DO NOT make any changes to any component of the Door, it may cause malfunction and damage.
We do not accept liability for malfunction or damages.
• Do not go under the door while it is opening or closing.
• The door must be leveled.
• DO NOT PULL the chain or unlocking lever while the door is moving.
• DO NOT PULL the door for use, otherwise it may cause malfunction and damage (It is just an
emergency brake).
• Regularly check the operating of the Door. If you notice any anomalies, please contact us.
• Our company reserves the right to change the design and specifications without prior notice.
• Please install the motor as shown. Otherwise we are not responsible for any damage.
 • 01 Motor
 • 01 Chain
 • 01 Bearing bracket
 • 01 Bracket
 • 01 Circular Plate II
 • 02 Circular Plates I
 • 01 Gear bracket
 • 01 Chain roll
 • 01 Square plate
Model Energy
Input Output torque Max. weight Rotation speed Height Bearing Chain
AC-6001P 220 V 410 Nm 600 kg 6.5 rpm 6 m 127 mm 10A
AC-8001P 220 V 640 Nm 800 kg 3.7 rpm 9 m 152.4 mm 10A
AC-10001P 220 V 710 Nm 1000 kg 5.5 rpm 9 m 152.4 mm 12A
NOTE: The Max. Weight value does not correspond to the maximum weight of the door. The door
weight should be less than Max. weight lifting. You should pay attention to wind resistance, guides
and resistance and other factors.
TECHNICAL CHARACTERISTICS
• Compact, attractive, safe designe and reliable performance.
• Light, silent, easy installation.
• Operations manual in case of power failure.
TECHNICAL DRAWING
Limit switch Motor Screw External switch:
• Ground (Yellow/Green)
•Brown
•Gray
•Black
Cover
Chain
Unlock
Lever

5A 5B
20m
L
2 3
A
B
ENEN
SQUARE PLATE BRACKET
04. INSTALLATION AND ADJUSTMENTS
Fix the bracket to the square plate as shown. Fix the square plate to the wall or wall bracket on
the opposite side of the gear.
Install the bearing as shown below.
BEARING INSTALLATION
GEAR BRACKET
Install the gear bracket on the wall or the bracket horizontally.
If the distance is insufficient, the bracket angle must be adjusted (installation angle can be
adjusted between 0° and 44°, make sure the chain stays in the vertical position).
Dimensions for installation (see table).
Model Distance to centers Length Width
AC-6001P/6003P 304 mm 515 mm 300 mm
AC-8001P/8003P 345.5 mm 580 mm 320 mm
AC-10001P/10003P 339 mm 600 mm 360 mm
Placa
Quadrada
Rolamento
Square plate
Join the two Circular Plates I and shaft to the Roll
Join Circular Plates II to the Roll
Bearing Circular Plate I Circular Plate II Gear
Roll Big gear Shaft
Bearing
Bracket
Suporte de
Rolamanto
INSTALLING THE MOTOR ON THE LEFT SIDE
It is possible to install the door motor on the left or right side. It is normally delivered on the right
side (seen from the opening side). If you need to switch to the left side, follow the instructions
below.
04. INSTALLATION AND ADJUSTMENTS
01 • Loosen the 4 screws
1
Parafusos
02 • Rotate 180 degrees
Parafusos
03 • Confirm that the chain is in
the vertical position, and retighten
the 4 screws.
Ensure there are no gaps between
the "A" sections.

6A 6B
ENEN
CHAIN
04. INSTALLATION AND ADJUSTMENTS
The Motor is supplied with a chain for manual lifting of the grille.
In case of using the chain, make slow movements to move the grille.
Cannot move the chain when the motor is running.
Forgreatersafety,whenmovingthe chain,turnoffthecircuitbreakerthatsupplies themotorization.
Pull the unlocking lever to quickly release the door.
MODEL CHAIN
AC-2001P • AC-3001P • AC5001P Pull in both directions
DC-300kg/500kg/750kg Pull in both directions
INSTALLATION OF THE GEAR
04. INSTALLATION AND ADJUSTMENTS
Fix the door motor to the gear. Make sure the nuts are tight and the chain is vertical position.
Limit switches are needed to adjust the opening and closing positions.
01 • Turn the screw to release the limit switch gear and open the door to the desired position,
turn the limit switch gear until you hear the OPEN switch click, and tighten the screw.
02 • Turn the screw to release the limit switch gear and close the door to the desired position, turn
the limit switch gear until you hear the CLOSE switch click, and tighten the screw.
03 • After adjustment, you can open and close the door to see if the door successfully reaches
the opening and closing positions. If the door does not reach the desired opening and closing
position, adjust the gear until you find the desired distance.
LIMIT SWITCHES ADJUSTMENT
WARNING: When pulling the unlocking lever to release the door, do not attempt to step
through the door. Otherwise, serious malfunctions or equipment damage may occur.
ATTENTION: Respect this information so that you do not damage the product or cause
personal injury.
Limit switch Limit switchScrews Screws
Limit
switch gear
Limit
switch gear

7
Supply: 100-240vac 50-60hz Output: 100-240vac 50-60Hz Watts: 750W max. Frequency: 433Mhz IP 44
CL
COM
MOTOR
OP
L
N
90-230
Vac
SEL SET
OP
L AB FE LAMP OP CL LECOMN
CL CE
321 4 5 6 7
V +
PHOTO
P.MAN
TIME.M
CMD.L
CMD
TIME.P
Supply: 100-240vac 50-60hz Output: 100-240vac 50-60Hz Watts: 750W max. Frequency: 433Mhz IP 44
CL
COM
MOTOR
OP
L
N
90-230
Vac
3
2
1 5
L AB FE
LAMP
COMN
321 4 5 6 7
V +
PHOTO
P.MAN
TIME.M
CMD.L
CMD
TIME.P
4
F
N
EN
05. CONNECTION SCHEME
Power
Supply
Power
Supply Power
Supply
Switch
1•Black CL
2•Brown OP
3•Gray COM
4•Ground
•Included as standard •Control board to work
only with remote control
•Control board to work with remote control,
pushbutton and allows placement of
Photocells/Security Systems
MOTOR MOTOR MOTOR
1•Black CL
2•Gray COM
3•Brown OP
4•Output Phase
5•Neutral output
1•Ground output
2•Ground input
3•Phase output
4•Neutral output
5•Brown OP
6•Gray COM
7•Black CL
1234
The rolling door motor must be connected to the ground, connect the ground wire to the gear
bracket. If the direction of movement of the door is wrong, the connection wires must be reversed.
CONNECTION TO SWITCH OR CONTROL BOARD
SWITCH MC4 EVO (OPTIONAL) MC75 (OPTIONAL)

8EN
06. MAINTENANCE
Check the door once a month. The door must be working without any defect.
Regularly check the limit switches.
For assistance, contact a qualified technician.
Our company reserves the right to change the design and specifications without prior notice.
Behavior Procedure Find the source of the problem
Door does not stop
at desired position. Check limit switches Replace limit switch or check connections and adjustments
Motor only works in
one direction Check limit switches or Photocells Check wires for Limit switches.
Motor fails when
external Pushbutton
is pressed
Check Pushbutton
contacts Replace switch or check connections
After stopping the
door goes down/up The locking brake is worn out Check compression spring on motor, add a spacer if necessary
TROUBLESHOOTING