Motorola IK10 User manual

Contents
Overview
Installation
1
2
3
4
Precautions
■If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself. (We
shall not be responsible for any problems caused by unauthorized repair or
maintenance.)
■Do not allow water or liquid intrusion into the camera.
■In the use of the product, you must be strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on wall
or ceiling, the device shall be firmly fixed.
■Do not use camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
■Do not aim the camera at the sun or extra bright place.
■Do not place the camera in extremely hot, cold (the operating temperature
shall be -30˚C~60˚C), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
IP Varifocal Camera
Quick Start Guide
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug Screwdriver
4 tapping screws PA 4×25
CVBS&DC
IN cables
①Loosen the nut from the main element (security cap).
②Run the network cable (without RJ 45 connector) through the both
elements. Then crimp the cable with RJ 45 connector.
③Connect the cable to the hermetic connector. Then tighten the nut and
the main cover.
■Please read this instruction carefully before using the product and keep
it for further reference.
■All the examples and pictures used here are for reference only.
■The contents of this manual are subject to change without notice.
2
13
1 Ethernet Connector
2 Audio Input (MIC)
3 Audio Output (HP)
4 CVBS Video Output
5 Alarm Input/Output
6 DC12V Power Connector
7A Zoom- (only available for type A)
8A Zoom+ (only available for type A)
7B Focus
8B Zoom
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS Interface
* Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera.
* Please install the camera in the dry environment. You'd better install back the
lower dome less than 4 hours after removing it.
*
Connecting Network Cable
10
7A
7B
8A
8B
9
11
Lens cover IR light hood
Type A: Motorized zoom camera
Type B: Manual zoom camera
*If the PoE switch is used to power the camera, DC12V power supply is not
required.
*It is recommended to install the security cap for outdoor installation.
①
②Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Trim Ring ∅4.6
90.2mm
90.2mm
Do not remove the protection film until finishing the installation.
Rotate the trim ring anticlockwise to remove it from the camera.
Figure 1 Figure 2
1
3
4
5
6
2
ALARM
4 3 2 1
Security cap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
ALARM
4 3 2 1
③Loosen the screws to open the lower dome.
④Route and connect these cables. Then secure the camera to the
ceiling or wall with the screws provided.
Hold it and rotate
Rubber plug
Lower dome
⑤Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor (See Figure 5) and then adjust the camera according to
the figure below to get an optimum angle.
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
Figure 3
Figure 4
* Install it when routing the cables
through the ceiling.

Lens cover
IR light hood
Zoom
Foucs
Zoom+
Zoom-
Monitor
⑦
put the trim ring onto the lower dome and then rotate it clockwise until it is
locked. Finally, remove the protection film softly.
Install the lower dome back to the camera and fix it with screws. Then
(Type A: Motorized zoom camera) (Type B: Manual zoom camera)
⑥ Insert a micro SD card. After that, adjust Zoom or Focus to obtain an optimum
image. Before adjustment, view the image of the camera on a monitor. For Type A,
press the T or W button. For Type B, (a) push the IR light hood to the position as
shown in Figure 6; (b) remove the lens cover; (c) adjust the Zoom and Focus; (d)
install back the lens cover and move the IR light hood back.
Figure 5 Figure 6
Figure 7
Insert a micro SD card
1. Make sure that the camera and the PC are well
connected
via LAN and in the same network.
2. Find the IP-Tool from the CD and then install it in the
computer. After that, run the IP-Tool as shown in this
section.
5. Network connection
There are two ways to access camera through LAN:
1. Access using IPTools App.
2. Access through browser, IE. (Explorer)
• IP Tools
3. Modify the IP address. The default IP address of this
camera is 192.168.226.201. Click the information of the
camera listed in the above table to show the network
information on the right hand. Modify the IP address
and gateway of the camera and make sure its network
address is in the same local network segment as that of
the computer. Please modify the IP address of your
device according to the practical situation.
For example, the IP address of your computer is
192.168.1.4. So the IP address of the camera shall be
changed to 192.168.1.X. After modification, please input
the password of the administrator and click “Modify”
button to modify the setting.
The default password of the administrator is “123456”.
4. Double-click the IP address and then the system will
pop up the IE browser to connect IP-CAM. After
downloading and running the Active X control, input the
user name and password in the window to access.
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in
the camera for the first time.
1. Set the IP address of the PC and make sure the
network segment should be as the same as the default
settings of IP-CAM. Open the network and share center.
Click “Local Area Connection” to pop up the following
window. Select “Properties” and then select Internet
protocol according to the actual situation (for example:
IPv4). Next, click “Properties” button to set the network
of the PC. Open the IE browser and input the default
address of IP camera and confirm.
• Direct access through PC
v2
Motorola Limited Warranty
This Motorola brand Product is produced under license by MDX
ELECTRONICS, LLC. Subject to the exclusions below, MDX
ELECTRONICS warrants that this Motorola brand product
("Product") will remain free from defects in materials and
workmanship under normal consumer usage for 2years. This
Warranty is your exclusive warranty. This Warranty extends only
to the first consumer purchaser and is not transferable. MDX
ELECTRONICS will at no charge repair or replace any Product
that qualifies under this Warranty. We may use functionally
equivalent reconditioned, refurbished, or new Products.
MOTOROLA and MDX ELECTRONICS are not responsible for
defects or damage that result from: (a) improper operation,
storage, misuse, abuse, maintenance, alteration, accident or
neglect, such as physical damage (cracks, scratches, etc.) to the
surface of the product or lens resulting from misuse; (b)
subjecting the Product or Accessory to abnormal usage or
conditions; (c) service provider alteration of the Product
including alteration of the Product’s firmware; or (d) other acts
which are not the fault of MOTOROLA or MDX ELECTRONICS,
are excluded from coverage.
Any implied warranties, including without limitation the implied
warranties of merchantability and fitness for a particular
purpose, shall be limited to the duration of this limited warranty.
This warranty is provided in lieu of all other warranties, express
or implied. In no event shall MOTOROLA or MDX ELECTRONICS
be liable, whether in contract or tort (including negligence) for
damages in excess of the purchase price of the product, or for
any indirect, incidental, special or consequential damages of any
kind, or loss of revenue or profits, loss of business, loss of
information or other financial loss arising out of or in connection
with the ability or inability to use the product, to the full extent
these damages may be disclaimed by law.
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length
of an implied warranty, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal
rights, and you may also have other rights that vary from one
jurisdiction to another.
To obtain support or need of information, doubts or questions,
please contact us at:
Tel: [phone] (México)
Tel: [phone] (México, Latin America and Caribe)
WhatsApp: [phone] (México, Latin America, Caribe)
Skype: soporte.motorolasecurity
Email: [email protected]
9:00AM - 5:00PM CST (Mon-Fri)
Manufactured, distributed or sold by MDX ELECTRONICS, LLC,
official licensee for this product. MOTOROLA and the Stylized M
Logo are trademarks or registered trademarks of Motorola
Trademark Holdings, LLC. and are used under license. All other
trademarks are the property of their respective owners.
©2020 Motorola Mobility LLC. All rights reserved.