Motorola NX-7510 Series User manual

NX-7510/NX-7520/NX-7530 Series
Integrated Services Platform
Installation Guide

2 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform
MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark
Office. © Motorola Solutions, Inc. 2014. All rights reserved.

Installation Guide 3
1.0 Introduction ....................................................................5
1.1 Document Conventions ..........................................................5
1.2 Warnings .....................................................................5
1.3 Site Preparation ................................................................6
1.4 Package Contents ...............................................................6
1.4.1 NX-7500 Series Accessories ..................................................6
1.4.2 Additional Recommended Equipment ...........................................7
1.5 Cautionary Statements ...........................................................7
1.6 Safety Instructions for Rack Mount Installations.......................................8
1.7 NX-7500 Series Power Supplies....................................................8
1.8 Power Supply Status LEDs ........................................................9
1.9 Power Protection................................................................9
2.0 Hardware Installation ...........................................................10
2.1 Installing the NX-7500 Series Services Platform ......................................11
2.2 NX-7500 Series Power Supply Installation ..........................................12
2.3 NX-7500 Series NMC Installation .................................................13
2.4 NX-7500 Series SFP Installation...................................................14
2.5 NX-7530 Disc Drive Assembly Replacement .........................................15
3.0 Specifications ..................................................................16
3.1 Physical Specifications ..........................................................16
3.2 Environmental Specifications .....................................................16
3.3 Power Specifications ...........................................................16
4.0 Regulatory Information ..........................................................17
4.1 Radio Frequency Interference Requirements - FCC ....................................17
4.2 Radio Frequency Interference Requirements - Canada .................................17
4.3 CE Marking and European Area (EEA) ..............................................17
4.4 Statement of Compliance ........................................................18
4.5 Waste Electrical and Electronic Equipment (WEEE)....................................19
4.5.1 Turkish WEEE Statement of Compliance ........................................20

4 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform
5.0 Motorola Solutions Support Center ...............................................21
6.0 NX-7500 Series China ROHS Compliance ..........................................22

Installation Guide 5
1 Introduction
The NX-7500 Series Integrated Services Platform lets you centrally administer networks of up to 2,048 WLAN
Access Points geographically dispersed over small or medium sized enterprise locations. WiNG 5 Access Points
intelligently handle the traffic flows, quality of service and security at remotely distributed locations, while the
NX-7500 series integrated services platforms provide a single point for configuration, policy setting, and remote
troubleshooting. Hotspot configuration, security policy management, and statistics aggregation are all done by
one integrated services platform. This efficient WLAN architecture makes controlling the network easier, and
reduces the hardware expense required to support large networks.
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
1.2 Warnings
• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the appliance to its power source.
• Remove jewelry and watches before installing this equipment.
• Verify the unit is grounded before connecting it to the power source.
• Verify any device connected to this unit is properly wired and grounded.
• Connect all power cords to a properly wired and grounded electrical circuit.
• Verify the electrical circuits have appropriate overload protection.
• Attach only approved power cords to the device.
• Verify the power connector and socket are accessible at all times during the operation of the equipment.
• Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions
that could cause a power surge.
• Verify there is adequate ventilation around the device, and ambient temperatures meet equipment operation
specifications.
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or equipment
malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or equipment
damage.

6 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform
1.3 Site Preparation
• Consult your site survey and network analysis reports to determine specific equipment placement, power
drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Provide a sufficient number of power drops for your equipment.
• Ensure adequate, dust-free ventilation to all installed equipment.
• Identify and prepare Ethernet and console port connections.
• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.
1.4 Package Contents
An NX-7500 series Integrated Services Platform ships with the following:
• NX-7500 series Integrated Services Platform
• Console cable
• Rack mount brackets
•NX-7510/NX-7520/NX-7530 Integrated Services Platform Installation Guide (this document)
1.4.1 NX-7500 Series Accessories
The following accessories are available for NX-7500 series Integrated Services Platform:
• 2 port 10Gb Network Mezzanine Card (NMC) module for use with 10Gb SFP+ transceivers
• 10GbPS short range 850nm multi-mode SFP+ transceiver for use with 10Gb NMC
• 10GbPS long range 10km single-mode SFP+ transceiver for use with 10Gb NMC
• 4 port 10Gb NMC Module for use with 1Gb SFP transceivers
• 1GbPS short range SFP transceiver for use with 1Gb NMC
• 1GbPS long range SFP transceiver for use with 1Gb NMC
• Spare AC power supply for NX-7510 or NX-7530
• Spare DC power supply for NX-7510 or NX-7530
• Mounting kit with sliding rails
• Spare 500GB hard drive for NX-7530

Installation Guide 7
1.4.2 Additional Recommended Equipment
• Standard, grounded 100-240 VAC 50/60 Hz connection
• Standard 19-inch 1U height equipment rack
• Depending on the power supply, an AC or DC Uninterruptible Power Supply (UPS) is recommended
1.5 Cautionary Statements
NOTE NX-7510 and NX-7530 integrated services platforms are initially configured with a
single AC power supply. An NX-7520 integrated services platform is initially configured
with two DC power supplies. Depending on the power supply, installation of an AC or
DC Uninterruptible Power Supply (UPS) is recommended if a second power supply is
installed in an NX-7510 or NX-7530.
CAUTION There are no user-serviceable components inside the NX-7500 series integrated
services platform. Opening the chassis will void the warranty.
CAUTION BIOS settings on the NX-7500 series integrated services platform should not be
changed. Changing any settings in the BIOS will void all warranty on the integrated
services platform.
CAUTION To prevent the integrated services platform from overheating, never install in an
enclosed area not properly ventilated or cooled. For proper airflow, keep the front
and back sides of the integrated services platform clear of obstructions and away
from the exhaust of other equipment.
CAUTION The recommended operating temperature is 32ºF to 104ºF/0ºC to 40ºC. Installation
in a closed or multi-rack assembly may raise the immediate ambient temperature
above the average room temperature. Exercise due caution.
CAUTION Ensure the electrical circuit through which the integrated services platform is
powered can safely accommodate a 300 Watt power supply.
CAUTION Motorola Solutions highly recommends you connect the NX-7500 series integrated
services platform to an Uninterruptible Power Supply (UPS).There are instances in
which the system software could become corrupt and un-recoverable in the event of
power loss, for example, during a system upgrade, database backup or database
restore operation.

8 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform
1.6 Safety Instructions for Rack Mount Installations
• Rack Mount Brackets - Do not lift the NX-7500 series integrated services platform using the rack mount
brackets.
• Rack Mount Rails - Use only industry-standard mounting kits when installing the NX-7500 series integrated
services platform, as improper mounting may result in hardware failure and hazardous conditions. Motorola
recommends using the mounting rails included with the integrated services platform.
• Elevated Operating Ambient - If installing the NX-7500 series integrated services platform in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than the
room ambient. Consideration should be given to installing the appliance in an environment compatible with the
maximum ambient temperature (Tma) specified by the manufacturer.
• Reduced Air Flow - Installation of the NX-7500 series integrated services platform in a rack should be such that
the amount of air flow required for safe operation of the equipment is not compromised.
• Mechanical Loading - Mounting the NX-7500 series integrated services platform in a rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
• Circuit Overloading - Consideration should be given when connecting the NX-7500 series integrated services
platform to the supply circuit so that protection is provided to the NX-7500 series integrated services platform
and supply wiring if any circuit overloads occur. Appropriate consideration of the equipment nameplate ratings
should be used when addressing this concern.
• Reliable Earthing - Reliable earthing of the rack mounted NX-7500 series integrated services platform should
be maintained.
• Particular attention should be given to supply connections other than direct connections to the branch circuit
(e.g., use of power strips).
1.7 NX-7500 Series Integrated Service Platform Power Supplies
NX-7510 and NX-7530 integrated services platforms are initially configured with a single AC power supply. An
NX-7520 integrated services platform is initially configured with two DC power supplies. Installation of an
Uninterruptible Power Supply (UPS) is recommended if a second power supply is installed in an NX-7510 or
NX-7530. To replace a failed power supply or install a new power supply, see NX-7500 Series Integrated
Services Platform Power Supply Installation on page 12.

Installation Guide 9
1.8 Power Supply Status LEDs
Each NX-7500 AC or DC power supply module has a single bi-color LED to indicate power supply status. The LED
is visible on the rear panel of each installed power supply.
The LED functionality for the power supplies is listed in the following table:
1.9 Power Protection
• If possible, use a circuit dedicated to data processing equipment. Commercial electrical contractors are familiar
with wiring for data processing equipment and can help with the load balancing of these circuits.
• Install surge protection. Be sure to use a surge protection device between the electricity source and the
NX-7500 series integrated services platform.
• Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a power outage. Some
UPS devices have integral surge protection. UPS equipment requires periodic maintenance to ensure reliability.
A UPS of the proper capacity for the data processing equipment must be purchased.
State Description
Off No power to all power supplies
Flashing red No input power
Flashing blue or green Power present. Only standby output on.
Blue or green Power supply on. Normal operation.
Red Power supply failure
Flashing red/blue
or
Flashing red/green
Power supply warning. Reaching end of life or exceeding
limits.

10 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform
2 Hardware Installation
The following sections describe the hardware installation for the NX-7500 series integrated services platform.
The following figure represents the front of the NX-7510 and NX-7520 models:
The following figure represents the front of the NX-7530 model:
To prepare for the installation:
1. Match the model number on the purchase order with the model numbers in the packing list and on the
integrated services platform.
2. Verify the contents of the box include the intended NX-7500 series integrated services platform and the
included hardware matches the package contents.
Part Number Description
NX-7510-100R0-WR NX-7510 base server appliance with single AC power supply
NX-7520-100R0-WR NX-7520 base server appliance with dual DC power supply
NX-7530-100R0-WR NX-7530 single AC power supply server appliance with RAID