Mountup MU0011 User manual

Step 2A Wall plate installation (wood stud)
2A-1
2A-2
Locate your studs. Verify and mark the center of the stud
by finding the stud edges using an awl, a thin nail, or an
edge-to-edge stud finder.
Position the wall plate at your desired height and
line up the holes with your stud center line. Level the
wall plate and mark the pilot hole locations.
01
2A-3
Drill pilot holes using a 7/32 in. (5.5mm) diameter drill bit.
IMPORTANT:
Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of thestud.
Hardware Included
Max:400x400mm/16x16"
Min:75x75mm /3x3"
26"~55"
(V8)
If you have any questions, please contact us.
Max:
(27KG)
60LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
Stud
Finder
HammerAwl Wood
Drill Bit
Masonry
Drill Bit
Wood Stud Installation Concrete Installation
1/2"
(13mm)
3/8"
(10mm)
7/32"
(5.5mm)
MAX:400mm/16"
MAX:
400mm/16" Max:
(27KG)
60LBS
Arm and Wall Plate
01 x1
Brackets
02 x2
Safety Locks
03 x2
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
M6M4 M8
Step 1-2 Select TV screw length
Correct Correct
Too Long
Too Short
Step 1-3
Attach the bracket
CAUTION: Ensure bracket is securely fastened before moving on to the next step.
Top of TV
Top of TV
(a) For Flat Back
(b) For Round Back / Extra Space
No!
No!
01
7/32 in
Ø5.5 mm
When attaching brackets to the flat screen, be careful not to over tighten screws and
be sure that screws do not bottom out in the mounting holes.
2.75in (70 mm)
Bubble Level
Min. 8"
(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
Min. Wood Stud Size:
nominal 2”(51mm)
actual 1 1/2”(38mm)
Min. Wood Stud Size:
nominal 4”(102mm)
actual 3 1/2”(89mm)
<16mm(5/8")
Drywall with wood studs
MU0011 INSTALLATION INSTRUCTION
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, please contact us.
●This product is designed for use in wood stud and solid concrete wall.
- DO NOT install into drywall alone.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not apply this product to any purpose not indicated by MOUNTUP.
● Incorrect installation may result in product damage or body injury. MOUNTUP shall bear no responsibility
for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,
please contact us.
Velcro cable ties X5 Bubble level X1
Hardware (Wall /Product)
Lag Bolts 5/16 x 2½ in
x3 x1
BA
Open-end wrench
M-A
Use the shorter screws
M-B
M-C
M-E
Not for M8 screws
M-FM-D
M-A
Use the longer screws
M-B
M-C
M-E
Not for M8 screws
Keep the
arrow up
4
1 2
43 5

2A-4
01
A
UP
01
Position the wall plate at
your desired height, level the
wall plate and mark the pilot
hole locations x3.
2B-1
Step 2B Wall plate installation (concrete or brick)
01
Drill pilot holes
2B-2
Adjustments Adjustments
C
Product dimensions:
Bubble Level
No!
2.75in (70 mm）
Ø 10 mm
Ø 10 mm
3/8in
2B-3
No!
Step 3 Lift and hang TV with brackets onto wall bracket
-10°
+5°
Tool-free Tilting Adjustment
If necessary
Tighten
B
If TV keeps tilting down, Pull TV to desired
angle then fasten tilting nuts with the open-end
wrench.
If needed, TV can be leveled ±3 degrees via adjusting the 4 nuts with the
open-end wrench.
Leveling adjustment (-3°/+3°)
±3°
± 3°
B
B
± 3°
A
Concrete Wall
Concrete Wall
Contact us to have these additional pieces shipped
directly to you.
Concrete wall anchor 3pcs (NOT INCLUDED)
Ø10*61mm
01
UP
01 A
Install wall plate using lag bolts .
Tighten the lag bolts until they are
pulled firmly against the wall plate .
01
A
01 A
01
Install wall plate using lag bolts
and anchors (not included).
Tighten the lag bolts until they are
pulled firmly against the wall plate .
A
02
01
TV brackets have two-height -shifts.
You can choose your desired height.
Hang the TV with brackets to the bracket.
The second choice
The first choice
03
03
Attech the saftety locks
Secure
58mm/2.3"
100mm
/3.9"
100mm
/3.9"
224mm
/8.8"
Φ 8.7mm/0.3"
31mm/1.2"
150mm
/5.9"
MAX:400mm/16"
MIN:75mm/3"
28.6mm/1.1"
Φ8.9mm/0.4 "
MAX:400mm/16"
MIN:75mm/3"
435mm/17.1"
425mm
/16.7"
30mm/1.2"
40mm/1.6"
505mm/19.9"
Φ 20mm/0.8"
206mm/8.1" 206mm/8.1"
73mm
/2.9"
431mm/17"
+5°
-10°
89mm/3.5"
20mm/0.8"
8
10 11
7
4
76 8
109 11