Move Green Global RC204 User manual

RC204 ZigBee Remote Control
Quick Start Guide

2
1. Introduction
The RC204 ZigBee Remote Control is used to control up
to four devices either at one time or individually. Take
controlling CCT Tunable LED bulbs as an example, you
are able to use it to control the following.
Turn the LED bulbs ON/OFF together or individually.
Individually adjust the brightness of a CCT tunable
LED bulb.
Individually adjust the color temperature of a CCT
tunable LED bulb.
2. Get to know your device
2.1. RC204 at a glance
Micro USB

3
Main LED indicator
All ON/OFF buttons
Lock Switch
Reset button
Individual ON/OFF
buttons & status LED
indicators

4
Color temperature
adjustment button
Status button
Brightness
adjustment button

5
2.2. Buttons and switch
All ON and all OFF button
Turn on and off all the paired devices such as LED
bulbs, smart plugs and power relays.
Four individual ON/OFF buttons
Turn ON/OFF the corresponding device individually.
Status button
The corresponding individual ON/OFF buttons will
illuminate according to its status.
Reset button
Set the device to join the ZigBee network.
Return the device to factory settings.
Brightness adjustment button
Adjust the brightness of the corresponding light
(Only when light can support this function)
Color temperature adjustment button
Adjust the color temperature of the corresponding
light (Only when light can support this function)
Tip: operational details will be described below.

6
2.3. Switch
Lock Switch
Set the device to be unable to bind with other
devices.
2.4. Micro USB
The micro USB is used to charge the battery of this
device. Connect it to a power outlet using the standard
Micro USB cable and USB power adapter.
2.5. LED indicators
Main LED indicator status
Main LED indicator

7
LED status
What it means
Main LED
solid Green
The battery charging is complete
Red LED
solid
The device is charging
Green LED
flashes one
time
1. After pairing with an individual
device
2. After restart (3 seconds reset
button push)
3. After full reset (10 seconds reset
button push)
Main LED
flashes red
three times
The device hasn’t joined a network
(when you press any button).
The main
LED flashes
red once
The device has joined a network
(when you press any button).

8
Status LED indicators
LED status
What it means
Individual
LED
indicator
shows solid
green
When pressing the status button if
the individual indicator shows solid
green then the paired device is ON
Individual
LED
indicator
shows solid
red
When pressing the status button if
the individual indicator shows solid
red, then the paired device is OFF
Green LED
flashes three
times
Pairing is successful
Red LED
flashes three
times
Pairing has failed
Individual LED
status indicators

9
3. Get started
To get started, you will need:
A SEG-X3 Smart Gateway
1 to 4 of CCT Tunable LED bulb LED622 (You will need
at least one LED bulb)
The mobile app
Then follow the steps below:
Step 1: Check the RC204 status.
Press any button to check if the main LED
indicator flashes red for three times.
Tip: if not, please return it to default factory settings by
using a pin key tool to press and hold the reset button
for ten seconds until the LED light flashes twice, now,
the main LED indicator should flash fast around ten
times.
Step 2: Select “Add new devices” in the menu of the
app.
Tip: for this step, you could also press the “Z” button of
the gateway for two seconds until the LED indicator
turns solid blue.

10
Step 3: Use a pin key tool to press the RC204 reset
button. Then the device will join the ZigBee network of
the gateway.
Step 4: If the remote control is paired into the gateway
successfully, the main LED indicator will flash green
three times. After pairing, please press any button to
check if the main LED indicator flashes red once
indicating that it is paired into the system.
Tip: If the main LED indicator flashes red three times
means it hasn’t added into the gateway. You will need to
repeat from step 2.
Step 5: Pair with 1-4 CCT Tunable LED bulb LED622
Note: please make sure the LED622 is also added into
the network of the gateway and can be controlled by the
mobile app before proceed.
(1) Make sure the LED bulbs that want to bind with this
remote control are powered on.
(2) Go to the “Automation” section, tap “Edit” (Android
phone) or swipe from left to right (iPhone), tap
“Identify”. The LED bulb will be flashing during the
“Identify” process.