Movincool CLIMATE PRO X14 User manual

1
No. Part Name Climate Pro X14/20/26 Climate Pro K12/18/24 Climate Pro D12/18
Nozzle Adapter Kit N/A 481769-0280 481769-0280
Nozzle Adapter Kit 481769-0310 N/A N/A
Cold Air Flange Kit N/A 481170-0480 481170-0480
Cold Air Flange Kit 481170-0450 481170-0450 481170-0450
Nozzle Kit N/A 484209-0480 484209-0480
Dual Duct 484209-0500 N/A N/A
Cold Air Self-supported Duct 481744-0091 481744-0091 481744-0091
Trim Ring 481851-0200 481851-0200 481851-0200
Accessory Installation Manual
484007-4970
WARNING
Disconnect power before installation. Beware that some residual voltage may remain in the unit
after the power is disconnected. There is a risk of electric shock.
Application Model Name Required Accessories Page No.
Aachment of Nozzle Climate Pro K12/18/24
Climate Pro D12/18 2
Aachment of Dual Duct Climate Pro X14/20/26 3
Aachment of Cold Air
Self-supported Duct
Climate Pro K12/18/24
Climate Pro D12/18 3
Climate Pro X14/20/26 4
B
C
D
E
A
G

2
1. Remove the louver from the upper front panel by
pressing on either of the lock tabs.
ATTACHMENT OF NOZZLE: Climate Pro K12/K18/K24/D12/D18
2. Aach the frame to the upper front panel by
placing the lock tabs to the upper opening
and hooks to the lower opening as shown.
3. Secure the adapter to the frame with the six (6)
push-in clips.
4. Aach the flange to the adapter with the six (6)
screws so that the aachment notch is on the
upper side.
Lock tabs
Louver
Upper Front Panel
5. Align the pin A with the aachment notch of
the flange. Insert the nozzle into the flange and
rotate clockwise until pin B is aligned with the
aachment notch.
Note:
To remove the nozzle, hold the nozzle ring and
rotate counterclockwise.
Lock tabs
Hook
Hook
Opening of Upper Front Panel
1
2
Aachment Notch
Flange
Ring
Pin A
Pin B
Nozzle Adapter Kit
Frame
Adapter
Screw (6)
Cold Air Flange Kit
Flange
Screw (6)
Nozzle
Prior to installation, separate the frame and adapter by removing the screws.
1
2
Adapter
Flange
Screw (6)
Aachment Notch
Frame
Adapter
Screw (6)

3
ATTACHMENT OF DUAL DUCT: Climate Pro X14/X20/X26
Align the pin A with the aachment notch of the flange. Insert
the nozzle into the flange and rotate clockwise until pin B is
aligned with the aachment notch.
Note:
To remove the nozzle, hold the nozzle ring and rotate
counterclockwise.
ATTACHMENT OF COLD AIR SELF-SUPPORTED DUCT:
Climate Pro K12/K18/K24/D12/D18
Screw (6)
Nozzle Adapter Kit Cold Air Flange Kit
Flange
Screw (4)
Clamp
Trim Ring
1. Remove the louver from the upper front panel and aach the Nozzle Adapter .
See step 1 to 3 on page 2.
2. Aach the cold air flange to the adapter with the
four (4) screws.
3. Pass the clamp through the cold air self-supported
duct and fasten it temporarily.
4. Hold the duct approximately 1 foot away from the
end and increase the diameter as shown.
5. Place the duct over the flange and decrease the
diameter until the duct fits exactly over the flange.
Secure with the clamp.
6. Place the trim ring over the end of the duct.
Decrease the diameter
Increase the diameter
Cold Air Self-supported Duct
Adapter
Cold Air Flange
Screw (4)
Aachment Notch
Flange
Ring
Pin A
Pin B
Prior to installation, separate the frame and adapter by removing the screws.
Flange
Cold Air Self-supported Duct
Clamp
Trim Ring

4
ATTACHMENT OF COLD AIR SELF-SUPPORTED DUCT:
Climate Pro X14/X20/X26
Trim RingCold Air Flange Kit
Flange
Screw (4)
Clamp
1. Take out the six (6) screws and remove the nozzle
adapter.
Screw (6)
Nozzle Adapter
2. Secure the metal adapter to the opening of the
upper front panel with the six (6) screws.
2. Aach the cold air flange to the adapter with the
four (4) screws
3. Pass the clamp through the cold air self-supported
duct and fasten it temporarily.
4. Hold the duct approximately 1 foot away from the
end and increase the diameter as shown.
5. Place the duct over the flange and decrease the
diameter until the duct fits exactly over the flange.
Secure with the clamp.
6. Place the trim ring over the end of the duct.
Decrease the diameter
Increase the diameter
Cold Air Self-supported DuctNozzle Apapter Kit
Screw (6)
Metal Adapter
Metal Adapter
Cold Air Flange
Screw (4)
Metal Adapter
Screw (6)
Flange Cold Air Self-supported Duct
Clamp
Trim Ring