Movincool Office Pro 36 User manual

OPERATION MANUAL
OFFICE PRO 36 and OFFICE PRO 60
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT
INSTALLATION AND USAGE AND READ ALL SAFEGUARDS
SECCIÓN EN ESPAÑOL
SECTION EN FRANÇAIS
AVAILABLE AT WWW.MOVINCOOL.COM

© 2009 DENSO SALES CALIFORNIA, INC.
All rights reserved. This book may not be reproduced or copied, in
whole or in part, without the written permission of the publisher. DENSO
SALES CALIFORNIA, INC. reserves the right to make changes without
prior notice. MovinCool is a registered trademark of DENSO
Corporation.

OPERATION MANUAL
OFFICE PRO 36 and OFFICE PRO 60

4
Table of Contents
FOREWORD.......................................................................................................5
Definition of Terms............................................................................................5
GENERAL WARNINGS & CAUTIONS..............................................................6
INVENTORY.......................................................................................................7
INSTALLATION..................................................................................................8
Choosing an Installation Site...........................................................................8
Moving the Unit .................................................................................................9
Plugging in the Unit ........................................................................................10
Warning Signal Connection ...........................................................................11
Fire Alarm Control Panel Connection ...........................................................12
LCDI Power Cord Instruction.........................................................................13
FEATURES.......................................................................................................14
OPERATION.....................................................................................................15
Control Panel...................................................................................................15
LCD Indicators.................................................................................................16
Set Clock..........................................................................................................17
Operating in COOL Mode ...............................................................................17
Operating in FAN ONLY Mode .......................................................................18
Changing from FAN ONLY Mode to COOL Mode.........................................18
How to Set a Program.....................................................................................19
How to View and Delete Program..................................................................20
How to Run and Stop Program......................................................................20
Operating Modes.............................................................................................21
Self-Diagnostic Codes ....................................................................................22
Empty the Drain Tank (If equipped)...............................................................23
Drain Pump......................................................................................................24
HOSE INSTALLATION ....................................................................................25
DAILY INSPECTION & MAINTENANCE.........................................................26
Empty the Drain Tank .....................................................................................26
Clean the Air Filters ........................................................................................26
Filter Removal Method....................................................................................26
Filter Cleaning Method....................................................................................27
In-Season/Off-Season Inspection & Maintenance........................................27
TROUBLESHOOTING .....................................................................................28
TECHNICAL SPECIFICATONS.......................................................................29

5
FOREWORD
Congratulations on purchasing the MovinCool portable air conditioner. This
manual explains how to assemble, install and operate the MovinCool Office Pro
36, and Office Pro 60 portable air conditioning units. Please read this operation
manual thoroughly to familiarize yourself with the features of the unit and to
ensure years of reliable operation.
You may also find it useful to keep this operation manual on hand for reference.
Components and/or procedures are subject to change without prior notice.
Definition of Terms
WARNING: Describes precautions that should be observed in order to
prevent injury to the user during installation or unit operation.
CAUTION: Describes precautions that should be observed in order to
prevent damage to the unit or its components, which may occur during
installation or unit operation if sufficient care is not taken.
Note: Provides additional information that facilitates installation on unit operation.

6
GENERAL WARNINGS & CAUTIONS
1. All electrical work, if necessary, should only be performed by qualified
electrical personnel. Repair to electrical components by non-certified
technicians may result in personal injury and/or damage to the unit. All
electrical components replaced must be genuine MovinCoolparts, purchased
from an authorized reseller.
2. The proper electrical outlet for MovinCool units must be equipped with a UL
approved ground-fault breaker to prevent electrical shock from the unit.
3. The Office Pro 36 is equipped with a six (6) foot (1.8 meter) UL approved LCDI
power cord, and the Office Pro 60 is equipped with a six (6) foot (1.8 meter)
power cord. For replacement, fixed location (hard wire) or power cord
lengthening (extension cord) cords are required, contact your reseller or a
qualified electrician for approved replacement methods.
4. Never fold or place heavy objects on the power cord. This could result in
damage to the power cord causing electrical shock or fire.
5. Do not place water or any other liquid on the unit. This can cause damage to
the unit and increase the risk of electrical shock.
6. Do not sit or stand on the unit.

7
INVENTORY
After unpacking your MovinCool unit, please check to make sure you have the
following items:
1. Office Pro 36 or Office Pro 60 MovinCool Unit (1)
2. Operation Manual / Product Registration (1)
Note: If any of these items were not included in the box or appear damaged,
please contact your MovinCool reseller for replacement.
OPERATION MANUAL /
PRODUCT REGISTRATION
OPERATION MANUAL /
PRODUCT REGISTRATION
OFFICE PRO 36 MOVINCOOL UNIT
OFFICE PRO 60 MOVINCOOL UNIT

8
INSTALLATION
Choosing an Installation Site
CAUTION: Following are some precautions to consider before choosing
your installation site. Please review carefully as improper installation may
result in personal injury or damage to the unit.
1. Do not use the unit in areas where leakage of flammable gas may occur.
2. Do not use the unit in areas where it is exposed to rain or water.
3. Do not use the unit in an atmosphere of excessively corrosive gas or vapor.
4. Do not use in areas where the temperature is outside the allowable operating
range.
5. Do not install the unit in sloping areas. The unit may move or topple over even
if the casters are set to the LOCKED position.
6. Install the unit in areas that can with-stand the weight of the unit. The Office
Pro 36 unit weighs approximately 427 lbs (194kg), and the Office Pro 60 unit
weighs approximately 623 lbs (282kg) (when the drain tank is full of water).
7. Allow 24 inches (610mm) of unobstructed airflow for both the air inlets and
outlets.
8. Do not use the Office Pro 36 unit at condition above 95°F (35°C).
9. Do not use the Office Pro 60 unit at condition above 106°F (41°C).

9
INSTALLATION (cont.)
Moving the Unit
Unlock all 4 casters and push the MovinCool unit, using the front or rear handles,
to a flat, level surface and set the casters back to the LOCKED position.
UNLOCKED
LOCKED
UNLOCKED
LOCKED

10
INSTALLATION (cont.)
Plugging in the Unit
1. Check the prong and surface of the power cord plug for dust/dirt. If dust and/
or dirt are present, wipe off with a clean, dry cloth.
2. Check the power cord, plug and prong for damage or excess play. If any
damage or excess play is found, contact your MovinCool reseller for repair.
WARNING:
1. If the power cord or plug is damaged, repair should only be
performed by qualified electrical personnel.
2. Do not connect/disconnect the power cord or attempt to operate
buttons with wet hands. This could result in electrical shock.
CAUTION:
1. Office Pro 36 ONLY: The AC outlet (208/230 VAC Single Phase, 60Hz)
needs to be rated at 30A or higher. Do not share the outlet with any
other instrument or equipment.
2. Office Pro 60 ONLY: The AC outlet (208/230 VAC Single Phase, 60Hz)
needs to be rated at 50A or higher. Do not share the outlet with any
other instrument or equipment.
Note:
1. Make sure the AC outlet is free of dirt, dust, oil, water or any other foreign
matter.
2. The Office Pro 36 is equipped with a UL approved LCDI cord and an approved
NEMA plug configuration (6-30).
The appropriate outlet must be used for this plug type.
3. The Office Pro 60 is equipped with an approved NEMA plug configuration (6-
50).
The appropriate outlet must be used for this plug type.

11
INSTALLATION (cont.)
Warning Signal Connection
(Output Signal Terminal L+ and L-)
The controller is equipped withawarningsignal output relay type (Form C, normal
open dry contact) which can be used to monitor the failure condition.
Relay contactor (not connector) is closed when the following condition has
occurred:
a. Tank full
b. Temperature sensor fails
c. High pressure switch error
The relay output contactor is rated 2A at 30VDC or 2A at 30VAC (resistive load)
and it is compatible with various warning devices such as alarm speaker, light
indicators, etc.
Connecting Warning Signal From Controller
1. Remove service panel from the rear of the unit.
2. Push out the back cap from inside. (In case of hand to remove, please push
inner latches of the cap one-by-one.)
3. Userecommendedwarningsignalwiresizefrom 16AWGto26AWGforasolid
wire, or 16AWG to 22AWG for a stranded wire with ring terminal for #6 stud
size.
4. Connect warning device to terminal L+ and L- according to its polarities.

12
INSTALLATION (cont.)
Fire Alarm Control Panel Connection
(Input Signal Terminal E+ and E-)
The controller is equipped with a normal open input signal, which can be
connected directly from the fire alarm control panel. When receiving the signal
from the fire alarm control panel, the unit turns off and does not turn back on until
it has been RESET.
Connecting Fire Alarm Control Panel to Controller
1. Remove service panel from the rear of the unit.
2. Squeeze the inner latches and push out the black cap from inside the panel
(see drawing of cap and inner latch shapes).
3. Userecommendedwarningsignalwiresizefrom 16AWGto26AWGforasolid
wire, or 16AWG to 22AWG for a stranded wire with ring terminal for #6 stud
size.
4. Connect warning device to terminal E+ and E- according to its polarities.
Cap
Latch
Input
Signal
Terminals
Output
Signal
Terminals

13
INSTALLATION (cont.)
LCDI Power Cord Instruction
(Office Pro 36 ONLY)
WARNING
CAUTION
Procedure
The LCDI device is non-serviceable device. Attempting to open the device may expose the
user to hazardous of electric shock, and could void warranties of this product.
Manufacturer’s reliability is limited to the replacement of the device.
1. Read the attention printed on the device for proper use and handling of this device.
2. This device is used for monitoring leakage current.
3. Do not immerse in water.
4. This device must only be plugged into appropriate wall outlet. Do not use on extension
cords or adapter. Do not remove ground prong.
5. In the event that this device trips, the cause of malfunction should be corrected first before
further use.
6. Using the device beyond recommended voltage poses risk to users.
7. Conductors inside this cord are surrounded by shields, which monitor leakage current.
These shields are not grounded, and they are periodically examined the cord for any
damage. Do not use this product in the event the shields become exposed.
8. Do not push TEST and/or RESET buttons in a short period.
Test device once when AC is installed to assure proper operation.
1. Plug into grounded power receptacle.
2. If light is not on, press RESET button once. Light should turn on.
3. Press TEST button once, light must turn off.
4. Press RESET button once again for use. Light should turn on.
5. If test fails, do not use.
POWER
LCDI
TEST
RESET
TEST Button RESET Button
<TYPE 1> <TYPE 2>
TEST Button
RESET Button
<TYPE 3>
TEST Button
RESET Button

14
FEATURES
For all models:
1. A digital electronic control panel, which allows the user to control the unit’s
operation easily.
2. Dual fan speeds (either HIGH or LOW) in both COOL and FAN ONLY modes.
3. Digital LCD display with blue backlight that indicates:
a. Clock with day and time
b. Room temperature and set point temperature
(either Fahrenheit or Celsius)
c. Fan speed status
d. Cool mode status
e. Program start time and stop time
f. Program run and stop
g. Status codes
h. Key locked option
4. Thesetpointtemperaturecan beadjustedbetween65°F and90°Fby theSET
TEMP buttons ( / ).
5. Fire alarm control panel connection ready for automatic shut off.
6. Automaticshutoffandwarningsignaloutputandalarmfortemperaturesensor
failure, cooling failure.
7. A condensate drain “TANK FULL” indicator (LED) and display (LCD).
8. An automatic restart feature when the power is lost and regained.
9. A condensate pump with safety switch shut off (optional accessory for Office
Pro 36).

15
OPERATION
Control Panel
Before operating the unit, it is important to familiarize yourself with the basic
controls located on the control panel.
1. COOL Mode Button Activates/deactivates the COOL mode/turns the
unit off.
2. FAN Mode Button Activates/deactivates the high, low, and off fan
speed.
3. SET TEMP Button ( / ) Temperature scale illuminates to indicate the
current LED temperatures being displayed are
either in °C or °F; also displays the clock when
programming.
4. ENTER Button Press to select set up value.
5. SET CLOCK Button Press to set clock (day and time).
6. SET PROG Button Press to set or view program.
7. RUN/STOP Button Activates/deactivates program(s).
8. TANK FULL LED Flashes when the drain tank is full.

16
OPERATION (cont.)
Control Panel (cont.)
LCD Indicators
Note: ROOM TEMP display range from 16°F to 109°F (-9°C to 42°C). In
Fahrenheit only, when display values are greater than 99°F, it displays values of
+0F (for 100°F),+1F (for 101°F) and +9F (for 109°F).
9. MO...SU Illuminates to indicate selected day of the week.
10. °C or °F Temperature displayed in either Fahrenheit or
Celsius (see Note).
11. AM/PM Illuminates to indicate AM or PM time of day.
12. PROGRAM Blinking during program editing mode.
13. PROGRAM ON Illuminates to indicate program is running.
14. START Illuminates to indicate program start time.
15. STOP Illuminates to indicate program stop time.
16. CLOCK Illuminates to indicate clock status.
17. FAN HI/LO Illuminates to indicate selected fan speed.
18. COOL ON/OFF Illuminates to indicate cool on or off.
19. LOCKED Illuminates to indicate key lock up.

17
OPERATION (cont.)
Set Clock
Prior to operating the Office Pro 36 or Office Pro 60 users should set the clock of
the controller to the correct time as shown in the steps below.
1. PressandholdtheSETCLOCKbutton
for 3 seconds or until beep.
(LCD indicates blinking “CLOCK” and
blinking “day of the week”.)
2. PressSETTEMP buttonstoselectday
of the week.
3. Press ENTER button to set hour.
4. Press SET TEMP buttons to select
desired hour.
5. Press ENTER button to set minute.
6. Press SET TEMP buttons to select
desired minute. Press SET CLOCK
button to exit set clock mode.
Note: User should check clock periodically to confirm clock accuracy.
Operating in COOL Mode
1. The unit can be operated in COOL mode by pressing the COOL ON/OFF
button (LCD indicates “COOL ON”).
Note: In COOL mode the unit can only be turned off by pressing the COOL
ON/OFF button again, not by pressing the fan buttons.
2. Change the fan speed by pressing the FAN HI/LO button.
3. Change the temperature set point by pressing the SET TEMP buttons ( / ).
Note: When turning the unit on, the set point and fan speed are determined by
the last operating mode. (This function does not apply to PROGRAM mode.)
Step 1 & 6
Step 2 to 5

18
OPERATION (cont.)
Operating in FAN ONLY Mode
1. The unit can also be operated in FAN ONLY mode by pressing FAN HI/LO
button (LCD indicates “FAN HI/LO” and “COOL OFF”).
2. The unit can then be turned off by pressing the FAN HI/LO button until fan
turns off (FAN ONLY mode speed sequences are HI→LO→OFF).
Changing from FAN ONLY Mode to COOL Mode
The COOL mode can be activated while the unit is operating in FAN ONLY mode.
To do this, simply press the COOL ON/OFF button (LCD indicates “COOL ON”).
Note: The FAN ONLY mode does not operate after the COOL mode has been
activated. After the COOL mode has been activated, the unit cannot be turned off
by pressing the fan buttons. The COOL ON/OFF button must be pressed.

19
OPERATION (cont.)
How to Set a Program
SET START TIME
1. Press and hold the SET PROG button
for 3 seconds or until beep.
2. PressSETTEMPbuttonstoselectday
of the week.
3. Press ENTER button.
4. Press SET TEMP buttons to select
desired hour.
5. Press ENTER button.
6. Press SET TEMP buttons to select
desired minute.
7. Press ENTER button.
SET STOP TIME
8. Press SET TEMP buttons to select day of the week.
9. Press ENTER button.
10. Press SET TEMP buttons to select desired hour.
11. Press ENTER button.
12. Press SET TEMP buttons to select desired minute.
13. Press ENTER button.
SET FAN SPEED
14. Press SET TEMP buttons to select desired fan speed.
15. Press ENTER button.
SET SET-POINT TEMPERATURE
16. Press SET TEMP buttons to select desired temperature.
17. Press ENTER button.
EXIT PROGRAM EDITING MODE
18. Press SET PROG button to exit program editing mode.
EDIT MULTIPLE PROGRAMS
19. Repeat step 1. to 18. to set up multiple programs.
Note: Maximum 7 programming sequences
Step 1 & 18
Step 2 to 17

20
OPERATION (cont.)
How to View and Delete Program
1. Press and hold the SET PROG button for 3 seconds or until beep.
2. To view edited program - While pressing and holding the SET PROG button,
press SET TEMP ( / ) to scroll the program sequence.
3. To delete a program - Press ENTER and SET PROG buttons once
simultaneously.
4. To delete multiple program - Press and hold ENTER and SET PROG buttons
simultaneously.
How to Run and Stop Program
1. Press RUN/STOP button to activate preset program (LCD indicates
“PROGRAM ON”). During PROGRAM RUN mode, if you push RESET (see
page 22), PROGRAM RUN mode is terminated. To resume PROGRAM RUN
mode, you must push RUN/STOP button again.
2. Press RUN/STOP button to stop program.
Note:
1. The unit returns to the previous mode if a program is turned off while it is
running.
2. The LCD continues to indicate “PROGRAM ON” during program activating.
3. Program can be set during power on standby, during unit running, or during
program running.
4. During programming, the unit returns to the previous mode if no activity occurs
within approximately 3 minutes.