Moxa Technologies VPort 26A-1MP Series User manual

Moxa VPort 26A-1MP User’s Manual
Edition 2.1, December 2015
www.moxa.com/product
© 2015 Moxa Inc. All rights reserved.

Moxa VPort 26A-1MP User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2015 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Before Getting Started
Before using your VPort 26A-1MP, please pay close attention to the following instructions:
After opening the VPort 26A-1MP box, compare the contents of the box with the Package Checklist in Chapter 1.
Notify your sales representative if any of the items are missing or damaged.
To prevent damage or problems caused by improper use, read the Quick Installation Guide (the printed handbook
included in the package) before assembling and operating the device and peripherals. You may also refer to Chapter
1, under Product Description, and all of Chapter 2, of this manual.
The VPort 26A-1MP IP Camera has been designed for various environments and can be used to build various
applications for general security or demonstration purposes. For standard applications, refer Chapter 2, Getting
Started, and Chapter 3, Accessing the VPort 26A-1MP Web-based Manager.
Important Note
Surveillance devices may be prohibited by law in your country. Since VPort is both a high performance surveillance
system and networked video server, verify that the operations of such devices are legal in your locality before
installing this unit for surveillance purposes.

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview...........................................................................................................................................1-2
Package Checklist...............................................................................................................................1-4
Product Features ................................................................................................................................1-5
Typical Application..............................................................................................................................1-6
Product Description.............................................................................................................................1-7
2. Getting Started ................................................................................................................................. 2-1
Before Getting Started ........................................................................................................................2-2
First-Time Installation and Configuration ...............................................................................................2-2
Hardware Installation...................................................................................................................2-2
Software Installation....................................................................................................................2-7
VPort 26A-1MP Dimensions..................................................................................................................2-9
Wiring Requirements.........................................................................................................................2-10
3. Accessing the VPort 26A-1MP’s Web-based Manager........................................................................ 3-1
Functions Featured on the VPort’s Web Homepage..................................................................................3-2
VPort’s Information .....................................................................................................................3-2
IP Camera Name.........................................................................................................................3-2
Camera Image View ....................................................................................................................3-2
Audio Control..............................................................................................................................3-3
Client Settings ............................................................................................................................3-3
System Configuration ..................................................................................................................3-4
Video Information .......................................................................................................................3-4
Show PTZ Control Panel (only supported by non-onvif version firmware: V1.x) ...................................3-4
Relay Control..............................................................................................................................3-4
Snapshot....................................................................................................................................3-4
4. System Configuration........................................................................................................................ 4-1
System Configuration by Web Console ..................................................................................................4-2
System ......................................................................................................................................4-3
General Settings..................................................................................................................4-3
Account Privileges................................................................................................................4-4
Local Storage ......................................................................................................................4-5
System Log.........................................................................................................................4-6
System Parameters..............................................................................................................4-7
Firmware Upgrade ...............................................................................................................4-8
Reset to Factory Default .......................................................................................................4-8
Reboot ...............................................................................................................................4-8
Network.....................................................................................................................................4-9
General Network Settings .....................................................................................................4-9
SMTP Server and Email Account Settings ..............................................................................4-14
Dynamic DNS....................................................................................................................4-15
Universal PnP ....................................................................................................................4-15
QoS (ToS).........................................................................................................................4-16
FTP Server Settings............................................................................................................4-16
Multicast...........................................................................................................................4-17
Configuring Multicast Settings .............................................................................................4-18
HTTP Event Server.............................................................................................................4-19
Accessible IP List ...............................................................................................................4-20
SNMP ...............................................................................................................................4-21
Configuring SNMP Settings..................................................................................................4-21
SNMP Read/ Write Settings .................................................................................................4-22
HTTP Event Server.............................................................................................................4-23
ModBus/TCP......................................................................................................................4-24
Telnet...............................................................................................................................4-25
LLDP ................................................................................................................................4-26
Video.......................................................................................................................................4-26
Image Settings..................................................................................................................4-26
Camera Setting .................................................................................................................4-27
ROI (Region of Interest) .....................................................................................................4-29
Privacy mask.....................................................................................................................4-30
Video Performance.............................................................................................................4-30
Audio.......................................................................................................................................4-33
Audio Source.....................................................................................................................4-33
PTZ .........................................................................................................................................4-33
Digital PTZ........................................................................................................................4-33
DynaStreamTM .........................................................................................................................4-34
Basic................................................................................................................................4-34
Conditions.........................................................................................................................4-35

Alarm ......................................................................................................................................4-35
System.............................................................................................................................4-35
Basic................................................................................................................................4-36
Schedule...........................................................................................................................4-37
Event Alarm ......................................................................................................................4-38
Digital Input......................................................................................................................4-39
Motion Detection................................................................................................................4-40
CGI Event .........................................................................................................................4-43
Camera Tamper.................................................................................................................4-44
A. Frequently Asked Questions.............................................................................................................. A-1
B. Modbus Address Table ...................................................................................................................... B-1
Read/Write Registers (Support Function Code 4 & Function Code 3)...........................................B-1
C. Time Zone Table................................................................................................................................ C-1
D. Technical Specifications ....................................................................................................................D-1

1
1. Introduction
The VPort 26A-1MP is a rugged IP camera designed for use in harsh environments. In addition to being able to
handle basic video feeds, many advanced features are also included to set up surveillance or web multimedia
applications. The VPort 26A-1MP is designed to provide stability, robustness, ease-of-use, and flexibility.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Typical Application

Product Description

Moxa VPort 26A-1MP Introduction
1-2
Overview
The VPort 26A-1MP is a vandal-proof, IP66-rated, fixed dome HD IP camera for use in harsh, outdoor
environments. With a maximum resolution of 1280 x 800, H.264/ MJPEG triple video streams and
day-and-night camera lens, the VPort 26A-1MP is especially well-suited for outdoor video surveillance
applications.
To enhance video image quality, the VPort 26A-1MP series is equipped with a megapixel 3 to 9 mm vari-focal
lens that meets versatile viewing angle and distance requirements. With a built-in removeable IR-cut filter, and
automatic switching from color to B/W images, the VPort 26A-1MP series is suitable for day-and-night use.
Along with built-in DNR (Digital Noise Reduction) and WDR (Wide Dynamic Range), the VPort 26A-1MP series
provides excellent image quality under low illumination or back light conditions.
The VPort 26A-1MP series is specially designed for outdoor applications with the following features: IP66 rain
and dust protection, high EMI/surge protection, -40 to 50°C or -40 to 75°C operating temperature without a
fan or heater, metal housing, and EN 62262 IK10 vandal-proof dome cover. In addition, the camera is built in
a dehumidified membrane for diffusing the moisture inside the camera.Users can choose either the VPort
P26A-1MP with PoE (Power over Ethernet, 802.3af) functionality, or the VPort 26A-1MP model with a 12/24
VDC or 24 VAC direct-wired power input.
The VPort 26A-1MP series is designed to provide both H.264 and MJPEG video streams and transmit up to 3
independent video streams (2 in H.264, and 1 in MJPEG) simultaneously. The camera can encode and transmit
up to 30 FPS for each of the H.264 and MJPEG streams. In addition, Moxa’s DynaStream™ function changes the
video frame rate automatically to help you control your network bandwidth budget and ease network system
management. The CBR Pro™ function guarantees no packet loss in limited bandwidth transmissions, ensuring
that images will not exhibit the mosaic effect. Advanced network security functions, such as 802.1x and SSH,
are also provided to prevent unauthorized access or data hijacking, which is critical for most surveillance
applications.
High Quality 1/2.7” HD CMOS sensor with advanced DNR and WDR
The VPort 26A-1MP IP camera uses a 1/2.7” HD CMOS sensor with DNR (digital noise reduction) and WDR (wide
dynamic range), which provide clearer video images in many environments, and especially in low illumination
(lux) environments.
Comes with 3 to 9 mm vari-focal lens, to meet a variety of viewing
requirements
The VPort 26A-1MP IP camera is designed with a 3 to 9 mm vari-focal lens for providing viewing angles from
148.4° to 43.8° diagonal. In addition, this lens supports auto-iris functionality, and possesses day & night
capability with IR-cut removable (ICR), which is suitable for most outdoor applications.
-40 to 50°C or -40 to 75°C operating temperature without fan and heater
The VPort 26A-1MP IP camera can work in -40 to 50°C, and VPort 26A-1MP-T can work in -40 to 75°C
operating temperature range, without the need of fan and heater, which can reduces the maintenance
workload substantially, especially in the outdoor or harsh environments.
IP66-rated form factor design for protection against dust and rain
The IP66-rated form factor design makes the VPort 26A-1MP suitable for use in outdoor environments, without
the need for additional protective housing. In addition, cable glands are provided free of charge to ensure that
attached cables also have IP66-rated protection.
Support for PoE (Power-over-Ethernet) or direct-wired power inputs
The VPort P26 supports standard 48 VDC power-over-Ethernet (IEEE 802.3af), and the VPort 26A-1MP
supports a direct-wired 12/24 VDC or 24 VAC power input.
High Performance H.264/MJPEG video compression
Video input can be efficiently compressed into H.264/MJPEG video stream packets in real time. This is done
without sacrificing remote monitoring capability or storage. Five levels of compression quality and four different
image resolutions provide greater versatility.

Moxa VPort 26A-1MP Introduction
1-3
CBR Pro™ for no video image packet loss when bandwidth is limited
An innovative CBR Pro™ function, where CBR stands for constant bit rate, is provided with the VPort 26A-1MP
series for guaranteeing no video image packet loss when bandwidth is limited. Even when the general CBR
function is activated, there is a chance of video image packet loss, which could cause a mosaic effect due to a
burst of bandwidth consumption in a short time (few milliseconds) while delivering image frames. With Moxa
CBR Pro™, even video images of high-speed objects, such as cars, will exhibit good image quality with no
mosaic effect.
2-way audio supported for a complete surveillance solution
The VPort 26A-1MP series support both audio input and audio output for voice over IP communication between
a field site and central site. The 2-way audio function not only saves time, but also saves the cost of needing
to add additional communication devices (such as a phone).
Three video streams for meeting versatile application requirements
VPort 26A-1MP is a powerful IP Camera. Aside from the high quality H.264 video compression, it can also
generate a maximum of three video streams: two H.264 and one MJPEG simultaneously, to meet the needs of
specific applications. For example, the user can view the h.264 video streams with full D1 resolution at 30FPS,
do MJPEG image analysis with full D1 resolution at 10FPS, and record the H.264 video streams with CIF
resolution at 30FPS.
Video latency under 200 ms (milliseconds) for more real-time video
In some mission critical environments, low video latency is a key requirement. For example, a highway
transportation system monitors vehicles that are moving very quickly. The video display in the traffic control
center needs to reflect actual current traffic conditions. Therefore, the video latency must be under 200ms.
SD Card for recording video locally when the network is down
The VPort 26A-1MP is equipped with an SD card socket (SDHC, V2.0) for local storage and offline data logging,
in the event of network interruptions. Currently, the VPort 26A-1MP supports SD cards up to 32 GB.
RTSP for easy integration with existing systems
RTSP (Real-time Streaming Protocol) is a client-server multimedia presentation control protocol, which ensures
interoperability among video devices and software. Hardware or software that supports RTSP streaming can
easily identify and decode the video stream without the hassle of codec installation. For example, users can
view video images from the VPort 26A-1MP directly with Quick Time and VLC, both of which support RTSP
streaming.
Multicast (IGMP) transmission for network efficiency
Transmitting digital video images via an IP network requires many times the bandwidth required for
transmitting general data. For this reason, the efficiency of network bandwidth management is one of the most
important factors that determine the performance of a video over IP surveillance system. The VPort 26A-1MP
supports multicast transmission with the IGMP protocol, which can reduce the bandwidth requirements when
multiple clients access the same video stream, and greatly increases the efficiency of network bandwidth
management.
Easy web access using standard browsers
There is no need to install new software to access the IP camera, since the embedded web server allows users
to use any popular web browser to access the IP camera from anywhere over the Internet. As long as you are
connected to the network, you will be able to view the same images seen by your cameras.
Built-in 3-area-selectable Video Motion Detection (VMD)
External sensors are not required, since the video image can be configured to detect motion in 3 areas, making
it easy to set up a security system either in your office or in the field. And the customizable settings allow you
to tune the system for both object size and sensitivity, making the IP Camera adaptable to different
environments.
Tamper alarm to detect when the camera has been painted or blocked
The tamper alarm helps prevent sabotage by detecting when the VPort 26A-1MP camera has been painted or
blocked.

Moxa VPort 26A-1MP Introduction
1-4
Weekly schedule for automated surveillance
The user-defined time period will check security settings on a weekly basis, and send notifications or drive
external devices, making the VPort 26A-1MP suitable for more versatile applications.
SDK support for developers
The high-performance IP camera can be integrated into many applications—without busting your budget—and
the complete programming interface of the Moxa VPort SDK PLUS makes the developer’s job easy and
straightforward. To ask about SDK requirements, please contact a Moxa sales representative for details and an
application form.
Package Checklist
The Moxa VPort 26A-1MP is shipped with the following items. If any of these items are missing or damaged,
please contact your sales representative for assistance.
•VPort 26A-1MP (includes 2-pin terminal block for power input) or VPort P26A-1MP (PoE power input)
•Screw handle accessory package
Torx screw driver for
attaching/detaching the
upper case
4 sets of self-tapping screws
(6 cm length) and anchors 9-pin terminal block for DI/Relay/Audio
•Cable glands accessories package
IP66 cable glands to ensure IP66
protection when the cables are
connected
•Sticker for camera mounting positions
•Quick Installation Guide
•Document & Software CD (includes User’s Manual, Quick Installation Guide, and VPort Utility)
•Warranty Statement
NOTE: Notify your sales representative if any of the above items are missing or damaged.

Moxa VPort 26A-1MP Introduction
1-5
Product Features
High Video Image Quality
•1/2.7” progressive CMOS sensor for HD (1280 x 720) resolution
•Day and night viewing capability with ICR (IR cut filter) and color /black & white image switch
•Supports DNR (digital noise reduction), BLC (back level control), and WDR (wide dynamic range) for better
image quality
•Equipped with 3 mm to 9 mm vari-focal megapixel lens for wide-range fields of view
•Minimum illumination up to 0.2 lux (color) and 0.05 lux (B/W) at F=1.2
•Image mirror and inverse
•350° pan, 85° tilt, and 360° rotate camera head angles for different installation positions.
•Supports up to 3 privacy mask areas and 4X digital zoom
Excellent Video/Audio streaming and network transmission performance
•Up to 3 simultaneous video streams for H.264 and MJPEG codecs
•Video stream up to 30 frames/sec at WXGA (1280 x 800) resolution
•DynaStream™ supported for optimal network efficiency
•CBR Pro™ supported for high image quality in limited bandwidth transmissions
•Video latency under 200 ms
•1 audio input and 1 audio output supported for complete video/audio surveillance solution
•WXGA/HD/SVGA/Full D1/ 4CIF/ VGA/ CIF/ QCIF resolution
•TCP, UDP, and HTTP network transmission mode
•Supports RTSP streaming
•Supports IGMP (ver.3) protocols for efficient network transmission
•Supports SNMP (V1/V2C/V3) for network system integration and management
•Supports QoS (ToS) for transmission priority
•Adjustable frame rate and bit rate control
•User-friendly IP filtering
•Supports IEEE802.1X for network access authentications
•Supports HTTPS and SSH for network transmission security
•UPnP Supported
•Up to 5 unicast video streams, and 50 multicast clients
•Supports multicast push for all multicast clients
•OnVIF standard supported for compatibility with other IP video products
•Modbus/TCP supported for direct communication with SCADA system
Rugged Design for Mission-critical Industrial Environments
•IP66 form factor protection for rain and dust
•Model available with PoE (802.3af) or 12/24 VDC and 24 VAC power input, with LED indicators
•Panel mounting for mounting on a ceiling, or outdoor installation kit for versatile installation method
•-40 to 50°C or -40 to 75°C (T model) operating temperature for critical industrial environments
•No heater or fan for long MTBF
•CE, FCC, UL60950-1
•5-year product warranty
Intelligent Alarm Triggering Capability
•Built-in tamper alarm, and VMD (video motion detection)
•1 DI and 1 relay output (DO) for sensors and alarms
•Supports video loss alarm
•Pre, trigger, and post snapshot images supported

Moxa VPort 26A-1MP Introduction
1-6
•24 MB video buffer for pre-event snapshot images
•Sequential snapshot images supported
•Supports SDHC slot for local storage with SD card in event recording
•Supports SMTP and FTP for alarm message transmission
•Supports HTTP event server
Video management and control
•Support for Moxa SoftNVR-IA IP surveillance software, a video recording and management solution
•Free: Moxa VPort SDK Plus with CGI Commands, ActiveX Control, and API support for third-party
developers
•ONVIF conformity for standardization and interoperability
NOTE
If you are interested in Moxa’s VPORT SDK PLUS, please go to Moxa’s website
www.moxa.com
to download the
package, or contact a Moxa sales representative for more information about this SDK
NOTE
If you are interested in SoftNVR
-IA IP surveillance software, please go to Moxa’s website (www.moxa.
com) to
download the trial version.
Typical Application

Moxa VPort 26A-1MP Introduction
1-7
Product Description
Form Factor
IP Camera Module

Moxa VPort 26A-1MP Introduction
1-8
Vari-focal Lens
The VPort 26A-1MP series comes with a day and night 3to 9mm megapixel lens for providing high quality video
images. Users can adjust the Zoom and Focus manually to get clear images regardless of the site environment.
NOTE
To tune the focus position, loosen the screw, and then turn the
lens head.
Pan, Rotation and Tilt Adjustment
Use the pan, rotation and tilt fasteners for panning, rotating and tilting the lens angles. To do this, the screws
must be loosened in advance. After the lens angles are correct, tighten the screws to fix the angles.
Light Sensor
The VPort 26A-1MP includes a light sensor for detecting illumination, which is for enabling the ICR (IR-cut filter
removable) function. When the illumination is under 3 lux, the image will be switched to night mode in black
and white, and when the illumination is greater than 5 lux, the image will be switched back to day mode in
color.
2-pin Terminal Blocks for Power Input
VPort 26A
-1MP series has comes in two models:

VPort 26A-1MP: 12/24 VDC or 24 VAC power inputs

VPort P26A-1MP: powered with PoE (Power over Ethernet, 802.3af)
Note: The 2
-pin terminal block shown here is for the direct-
wired power input of
the VPort 26A
-1MP.
NOTE
The specifications of the direct
-wire power input are 12-32 VDC for 12/24 VDC power input, or 18-
30 VAC for
24 VAC power input. The maximum power consumption is
4.7 Watt.

Moxa VPort 26A-1MP Introduction
1-9
9-pin Terminal Block Connector for DI, DO, and Audio
The VPort 26A-1MP supports 1 DI (digital input), 1 DO (relay output), 1 audio input (line-in or mic-in), and 1
audio output (line-out) through the 9-pin terminal block.
DO
(Relay Output)
NO (Normal Open) Max. 1A, 24 VDC
Initial status is Normal Open
C (Common)
NC (Normal Close)
DI (Digital Input) + Low: +13V to +30V
High: -30V to +3V
-
LED Indicators and DIP Switches
The VPort
26A-1MP has 3 LEDs for indicating the power status, 10/100 Mbps Ethernet
link, and system status. In addition, one DIP switch (No.2) is provided for enabling or
disabling the LED light for users who do not want the LED light to be visible at night.
LED Description
Power On: power on
Off: power off
10/100 M Amber: Ethernet link is 10 Mbps
Green: Ethernet link is 100Mbps
System Red On Hardware initialization
Red blinking Software initialization
Green On System boot-up successfully
Green blinking Firmware upgrade proceeding
DIP Switch 1 Reserved
DIP Switch 2 On: LED light is on
Off: LED light is off
SD card Socket (SDHC)
The VPort 26A-1MP supports a standard SDHC interface for local storage with a current maximum size of 32 GB.
The user can use an SD card which is fits this specification. Currently, the local storage supports triggered video
recording when an event has occurred.

Moxa VPort 26A-1MP Introduction
1-10
NOTE
The VPort 26A
-1MP supports a s
tandard SDHC interface. Users can use SD cards suitable for this specification.
Transcend or Sandisk SD cards are recommended, particularly Sandisk Extreme III SD, because of their rapid
read/write speed.
NOTE
To check if the SD card has been successfully mounted, access the VPort’s web
-based manager and check
under system configuration
-> Local storage.
Reset Button
The reset button is used to reset the camera hardware.
1. Reboot:
To reboot the VPort 26A-1MP, power it off and then power it back on again, or push the RESET button one time.
The System LED will light in red as the POST (Power on Self Test) process runs. When the rebooting process is
finished, the System LED will change to a green color.
2. Restore to Factory Settings:
To restore the VPort 26A-1MP to the factory default settings, press the reset button continuously until the
System LED blinks in red. After the system LED stops blinking, release the reset button. The POST process will
run, and the VPort will reboot. The System LED will light in green when the VPort has finished rebooting.
RJ45 Ethernet Port
The RJ45 Ethernet port is for 10/100Mbps network transmission, in addition to PoE (power over Ethernet,
802.3af) power supply for VPort P26A.
NOTE
The VPort P26 supports standard IEEE 802.3af Power
-over-Ethernet (PoE). T
he maximum power consumption
is about
5.8W.
NOTE
The equipment is designed for in building installation only and is not intended to be connected to exposed
(outside
plant) networks.

2
2. Getting Started
This chapter includes information about how to install a VPort 26A-1MP IP camera.
The following topics are covered in this chapter:

Before Getting Started

First-Time Installation and Configuration
Hardware Installation
Software Installation

VPort 26A-1MP Dimensions

Wiring Requirements

Moxa VPort 26A-1MP Getting Started
2-2
Before Getting Started
In what follows, “user” refers to those who can access the IP camera, and “administrator” refers to the person
who knows the root password that allows changes to the IP camera’s configuration, in addition to providing
general access. Administrators should read this part of the manual carefully, especially during installation.
First-Time Installation and Configuration
Hardware Installation
Step 1: Open and remove the upper case.
Use the security Torx to loosen the upper case screws.
Step 2: Remove the inner case
Loosen 4 screws, and take out the IP camera module.

Moxa VPort 26A-1MP Getting Started
2-3
Step 3: Connect the cables.
a) Open the conduit hole. (use the side conduit hole as example)
b) Prepare the cable gland (if required).
c) Use the cable gland to assemble the cables.
NOTE
When
installing the cable gland, make sure the 2 rubber rings are assembled properly for IP66 protection. If
necessary, use silicon sealant.

Moxa VPort 26A-1MP Getting Started
2-4
d) Connect the cables to the IP camera module’s connectors.
Connect the Ethernet cable to RJ45 Ethernet port, as well as the terminal blocks with power line and
DI/DO/Audio lines (if used).
NOTE
Be sure to arrange the cables carefully to make sure that all cables are connected properly. We recommend
connecting the Ethernet cable first, and then the 9
-pin terminal block. Connect the 2-pin terminal block last.
NOTE
The conduit hole must face downward to provide the VPort 26A
-1MP with IP66 protection against rain when
installed in an outdoor environment.

Moxa VPort 26A-1MP Getting Started
2-5
Step 4: Mount the bottom case on the ceiling or accessory’s mounting kit
(VP-MK2)
a) Mounting on the ceiling
Step 1:
Use the installation stick or attach the bottom case to the appropriate mounting location on the
wall, and mark the positions of the four screw holes with a pen or a pencil.
Step 2:
In
the marked locations, drill a hole slightly smaller than the supplied screw anchors.
Step 3:
P
ut anchors into these drilled holes.
Step 4:
Fasten the
bottom case with the four self-tap screws.
b) Mounting on the accessory’s mounting kit (VP-MK2)
Step
1:
Fasten the bottom case on the plate with the four machine screws, which are provided in VP
-
MK2’s
accessory package.
Step 2:
Assemble the mounting kit with the selected accessory.
VPort 26A-1MP + VP-MK2 + VP-520L VPort 26A-1MP + VP-MK2 + VP-520HB
NOTE
Choose the appropriate mounting accessories based on the installation requirements.