Moxa Technologies VPort 56-2MP User manual

Moxa VPort 56-2MP Rugged IP Camera
User’s Manual
Second Edition, September 2014
www.moxa.com/product
© 2014 Moxa Inc. All rights reserved.

Moxa VPort 56-2MP Rugged IP Camera
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2014 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax: [phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax: [phone]

Before Getting Started
Before using your VPort 56-2MP, please pay close attention to the following instructions:
After opening the VPort 56-2MP box, compare the contents of the box with the Package Checklist in Chapter 1.
Notify your sales representative if any of the items are missing or damaged.
To prevent damage or problems caused by improper use, read the Quick Installation Guide (the printed handbook
included in the package) before assembling and operating the device and peripherals. You may also refer to Chapter
1, under Product Description, and all of Chapter 2, of this manual.
The VPort 26 IP Camera has been designed for a variety of environments and can be used to build various applications
for general security or demonstration purposes. For standard applications, refer Chapter 2, Getting Started, and
Chapter 3, Accessing the VPort 56-2MP Web-based Manager.
Important Note
Surveillance devices may be prohibited by law in your country. Since the VPort is both a high performance surveillance
system and networked video server, verify that the operations of such devices are legal in your locality before
installing this unit for surveillance purposes.

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview ...........................................................................................................................................1-2
Package Checklist ...............................................................................................................................1-2
Product Features ................................................................................................................................1-3
Typical Applications.............................................................................................................................1-4
Product Description.............................................................................................................................1-4
2. Getting Started.................................................................................................................................. 2-1
Before Getting Started ........................................................................................................................ 2-2
First-Time Installation and Configuration ...............................................................................................2-2
Software Installation.................................................................................................................... 2-2
Wiring Requirements...........................................................................................................................2-4
3. Accessing the VPort’s Web-based Manager....................................................................................... 3-1
Functions Featured on the VPort’s Web Homepage..................................................................................3-2
VPort’s Information .....................................................................................................................3-2
IP Camera Name .........................................................................................................................3-2
Camera Image View ....................................................................................................................3-2
Client Settings ............................................................................................................................3-3
System Configuration ..................................................................................................................3-4
Video Information ....................................................................................................................... 3-4
4. System Configuration........................................................................................................................ 4-1
System Configuration by Web Console ..................................................................................................4-2
System ......................................................................................................................................4-3
General Settings ..................................................................................................................4-3
Account Privileges ................................................................................................................4-4
Local Storage ......................................................................................................................4-5
System Log History ..............................................................................................................4-6
System Parameters ..............................................................................................................4-7
Firmware Upgrade................................................................................................................4-7
Reset to Factory Default .......................................................................................................4-8
Reboot ...............................................................................................................................4-8
Network .....................................................................................................................................4-9
General Network Settings .....................................................................................................4-9
SMTP Server and Email Account Settings .............................................................................. 4-14
FTP Server Settings............................................................................................................ 4-15
Dynamic DNS .................................................................................................................... 4-15
Universal PnP .................................................................................................................... 4-16
QoS (ToS)......................................................................................................................... 4-16
Multicast ........................................................................................................................... 4-17
Configuring Multicast Settings ............................................................................................. 4-18
HTTP Event Server ............................................................................................................. 4-19
Accessible IP List ............................................................................................................... 4-20
SNMP ............................................................................................................................... 4-21
Configuring SNMP Settings.................................................................................................. 4-21
Modbus/TCP ...................................................................................................................... 4-23
IEEE 802.1X ...................................................................................................................... 4-23
Telnet............................................................................................................................... 4-24
LLDP ................................................................................................................................ 4-24
Video ....................................................................................................................................... 4-24
Image Settings .................................................................................................................. 4-24
Camera Setting ................................................................................................................. 4-26
ROI (Region of Interest) ..................................................................................................... 4-28
Privacy Mask ..................................................................................................................... 4-29
Camera Modulation ............................................................................................................ 4-29
Video Performance ............................................................................................................. 4-30
Audio....................................................................................................................................... 4-32
PTZ ......................................................................................................................................... 4-32
Digital Zoom ..................................................................................................................... 4-32
PT Scanner........................................................................................................................ 4-33
Camera Control ................................................................................................................. 4-33
Focus....................................................................................................................................... 4-34
DynaStreamTM........................................................................................................................... 4-35
Basic ................................................................................................................................ 4-35
Conditions......................................................................................................................... 4-36

Alarm ...................................................................................................................................... 4-36
System Alarm.................................................................................................................... 4-36
Basic ................................................................................................................................ 4-37
Schedule........................................................................................................................... 4-39
Event Alarm ...................................................................................................................... 4-40
Video Motion Detection ....................................................................................................... 4-40
CGI Event ......................................................................................................................... 4-42
Sequential Snapshot........................................................................................................... 4-43
Digital Input...................................................................................................................... 4-43
A. Frequently Asked Questions.............................................................................................................. A-1
B. Modbus Address Table ...................................................................................................................... B-1
C. Time Zone Table................................................................................................................................ C-1
D. Technical Specifications .................................................................................................................... D-1

1
1. Introduction
The VPort 56-2MP is a rugged Full HD resolution (1080P) box type IP zoom camera designed for use in harsh
environments. In addition to being able to handle basic video feeds, many advanced features are also included
to set up surveillance or web multimedia applications. The VPort 56-2MP is designed to provide stability,
robustness, ease-of-use, and flexibility.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Typical Applications

Product Description

VPort 56-2MP Introduction
1-2
Overview
Rugged Design
The VPort 56-2MP series is the world’s first rugged IP camera that can withstand environmental temperatures
ranging from -40 to 75°C without cooling fan. It is an industrial-grade, H.264 box-type IP camera with Full HD
resolution (1920 x 1080), to enhance surveillance system efficiency while delivering state-of-the-art video
quality. Optional housing and PT scanner accessories are available for indoor and outdoor installation.
Superb Video Quality
The VPort 56-2MP is equipped with 10x optical zoom and a 16x digital zoom module, with a built-in removable
IR-cut filter and automatic color mode switching, the VPort 56-2MP Series is suitable for day-and-night use.
Highly-tuned ROI (Region of Interest), and 3DNR (3D Digital Noise Reduction) functions enable the VPort
56-2MP series to produce exceptionally clear images.
Convenient Installation
The VPort 56-2MP series is designed for indoor and outdoor applications that require operational reliability. It
is a unique and competitive camera in the IP CCTV market, with features such as high EMI/surge protection,
optional IP66 housing for rain/dust protection, and -40 to 75°C operation without requiring a heater or cooling
fan. This camera is available with PoE+ (Power over Ethernet, 802.3at) or with wired power input supporting
12/24 VDC or 24 VAC.
High Video Performance and Network Security
The VPort 56-2MP series can encode analog video into both H.264 and MJPEG video streams and can transmit
up to 3 independent video streams (2 in H.264, and 1 in MJPEG) simultaneously. Advanced video encoding
technology enables the camera to support up to 30 FPS for each of the H.264 and MJPEG streams. Advanced
network security functions, such as 802.1x and SSL/SSH, are also provided to prevent unauthorized access or
data hijacking, a critical feature for many surveillance applications.
Package Checklist
Moxa’s VPort 56-2MP Series is shipped with the following items. If any of these items is missing or damaged,
please contact your customer service representative for assistance.
•1 × VPort 56-2MP (one of following models)
Standard model Description
VPort 56-2MP-CAM10X
Full HD zoom IP camera, RJ45 Ethernet port, 12/24 VDC or 24 VAC or PoE,
0 to 60°C
VPort 56-2MP-CAM10X-T
Full HD zoom IP camera, RJ45 Ethernet port, 12/24 VDC or 24 VAC or PoE,
-40 to 75°C
VPort 56-2MP-CAM10X -S-SC Full HD zoom IP camera, single-mode fiber Ethernet port, 12/24 VDC or 24
VAC, 0 to 60°C
VPort 56-2MP-CAM10X-S-SC-T Full HD zoom IP camera, single-mode fiber Ethernet port, 12/24 VDC or 24
VAC, -40 to 75°C
•Terminal block accessory package
3-pin terminal block for power
input
9-pin terminal block for RS-485 DX+
and DX-
•Quick installation guide

VPort 56-2MP Introduction
1-3
•Documentation and software CD (includes User’s Manual, Quick Installation Guide, and VPort Utility)
•Warranty card
NOTE: Notify your sales representative if any of the above items are missing or damaged.
NOTE
Check the model name on the VPort’s side label to determine if the model name is correct for
your order.
NOTE
This product must be installed in compliance with your local laws and regulations.
Product Features
•Sensor: 1/2.5" Full HD progressive scan CMOS
•Lens: 6.3 to 63 mm auto focus zoom lens
•Illumination (low light sensitivity):
Color: 0.2 lux at F1.8
B/W: 0.05 lux at F1.8
•White Balance: ATW/AWB
•Auto Electronic Shutter: On/Off
•S/N Ratio: More than 50 dB (AGC OFF)
•ICR Control: Auto (light sensor control) or DI control
•DNR: Built-in 3DNR
•AGC Control: On/Off
•Auto Exposure: On/Off
•Image Rotation: Flip, Mirror, and 180° rotation
•Image Setting: Manual tuning and sharpness
•Video Compression: H.264 (ISO/IEC 14496-10) or MJPEG
•Video Outputs: Ethernet
•Video Streams: Up to 3 video streams (2 x H.264 and 1 x MJPEG)
Stream 1: H.264, 1920 x 1080 resolution (max.)
Stream 2: H.264, 1280 x 720 resolution (max.)
Stream 3: MJPEG, 720 x 480 resolution (max.)
•Video Motion Detection: 3 independently configurable motion areas
•Scheduling: Daily repeat timing schedule
•Imaging: JPEG snapshots for pre/trigger/post alarm images
•Video Recording: Event recording, stored on the SD card
•Email/FTP Messaging: Automatic transfer of stored images via email or FTP when alerted
•Custom Alarms: HTTP event servers for setting customized alarm actions
•Pre-alarm Buffer: 84 MB video buffer for JPEG snapshot images
•Advanced Software Feature:
DynaStream™ support for automatic adjustment of frame rate
8 privacy mask areas provided
ROI (Region of Interest) configuration for up to 3 areas
•Safety: UL 60950-1, EN 50121-4, NEMA TS2
•EMI: FCC Part 15, CISPR (EN 55022) class A
•EMS: EN 61000-4-2 (ESD), Level 3 EN 61000-4-3 (RS), Level 3 EN 61000-4-4 (EFT), Level 3 EN 61000-4-5
(Surge), Level 3 EN 61000-4-6 (CS), Level 3 EN 61000-4-8, EN 61000-4-11
•Shock: IEC 60068-2-27
•Freefall: IEC 60068-2-32

VPort 56-2MP Introduction
1-4
•Vibration: IEC 60068-2-6
•Warranty: 3-year warranty (not including moving parts)
NOTE
If you are interested in Moxa’s VPORT SDK PLUS, please go to Moxa’s website
www.moxa.com
to download the
package, or contact a Moxa
sales representative for more information about this SDK.
NOTE
For moving parts, please check Moxa's warranty policy online at www.moxa.com/warranty
Typical Applications
With the industrial grade design and specifications, the VPort 56-2MP is suitable for both mission critical
applications and general purpose surveillance systems, including the following:
•ITS (Intelligent Transportation System)
•City surveillance
•Railway wayside surveillance
•Railway station surveillance
•Industrial automation surveillance
•Oil & Gas facility surveillance
•Mining facility surveillance
Product Description
Top View
•SD Card Slot: You can remove the SD card slot cover and insert an SD card for disconnection/event local
storage.
•Mounting Bracket Screw Hole: Screw holes for fastening the camera to the protective housing.
•Reset Button: Use a pointed object to push in the reset button. Press and release to reboot, or press and
hold until the system reboots to load factory defaults.

VPort 56-2MP Introduction
1-5
Back Panel View
1. Phone jack for audio output.
2. Phone jack for audio input.
3. RJ45 port for PoE/non-PoE connection
4. Ground screw for connecting the grounding wire
5. 3-pin terminal block for the power input
6. LED indicator to show network and system status. Green indicates normal operation.
7. LED indicator to show power status. Green indicates normal operation.
8. 9-pin terminal block for RS-485 and DI and relay
NOTE
The VPort 56
-2MP can be powered by a 12-32 VDC or 18-30 VAC power input, or Power over Ethernet (PoE+
,
802.3a
t). For power redundancy, use DC or AC power together with PoE.

2
2. Getting Started
This chapter includes information about how to install a VPort 56-2MP IP camera.
The following topics are covered in this chapter:

Before Getting Started

First-Time Installation and Configuration
Software Installation

Wiring Requirements

VPort 56-2MP Getting Started
2-2
Before Getting Started
In what follows, “user” refers to those who can access the IP camera, and “administrator” refers to the person
who knows the root password, which allows making changes to the IP camera’s configuration and obtaining
general access. Administrators should read this part of the manual carefully, especially during installation.
First-Time Installation and Configuration
Software Installation
Step 1: Configure the VPort 56-2MP’s IP address.
When the VPort 56-2MP is first powered on, the POST (Power On Self Test) will run for a few moments (about
30 seconds). The network environment determines how the IP address is assigned.
Network Environment with DHCP Server
For this network environment, the unit’s IP address will be assigned by the network’s DHCP server. Refer to the
DHCP server’s IP address table to determine the unit’s assigned IP address. You may also use the Moxa VPort
and Ether Device Configurator Utility (edscfgui.exe), as described below:
Using the Moxa VPort and EtherDevice Configurator Utility (edscfgui.exe)
1. Run the edscfgui.exe program to search for the VPort. After the utility’s window opens, you may also click
on the Search button to initiate a search.
2. When the search has been completed, the Model Name, MAC address, IP address, serial port, and HTTP port
of the VPort will be listed in the utility’s window.
3. You can double click the selected VPort, or use the IE web browser to access the VPort’s web-based
manager (web server).
Non DHCP Server Network Environment
If your VPort 56-2MP is connected to a network that does not have a DHCP server, then you will need to
configure the IP address manually. The default IP address of the VPort 56-2MP is 192.168.127.100 and the
default subnet mask is 255.255.255.0. Note that you may need to change your computer’s IP address and
subnet mask so that the computer is on the same subnet as the VPort.

VPort 56-2MP Getting Started
2-3
To change the IP address of the VPort manually, access the VPort’s web server, and then navigate to the
System Configuration Network General page to configure the IP address and other network settings.
Check the Use fixed IP address to ensure that the IP address you assign is not deleted each time the VPort
is restarted.
Step 2: Access the VPort 56-2MP’s web-based manager
Type the IP address in the web browser’s address input box and then press enter.
Step 3: Install the ActiveX Control Plug-in
A security warning message will appear the first time you access the VPort’s web-based manager. The message
is related to installing the VPort AcitveX Control component on your PC or notebook. Click Yes to install this
plug-in to enable the IE web browser for viewing video images.
NOTE
For Windows XP SP2 or above operating systems, the
ActiveX Control component will be blocked for system
security reasons. In this case, the VPort’s security warning message window may not appear. Users should
unlock the ActiveX control blocked function or disable the security configuration to enable the installation of the
VPort’s ActiveX Control component.
Step 4: Access the homepage of VPort 56-2MP’s web-based manager.
After installing the ActiveX Control component, the homepage of the VPort 56-2MP’s web-based manager will
appear. Check the following items to make sure the system was installed properly:
1. Video Images
2. Video Information

VPort 56-2MP Getting Started
2-4
Step 5: Access the VPort’s system configuration.
Click on System Configuration to access the overview of the system configuration to change the
configuration. Model Name, Server Name, IP Address, MAC Address, and Firmware Version appear in
the green bar near the top of the page. Use this information to check the system information and installation.
For details of each configuration, check the User’s Manual on the software CD.
Wiring Requirements
SAFETY FIRST
•
Be sure to disconnect the power cord before installing and/or wiring your Moxa VPort 56-2MP.
•
Calculate the maximum possible current in each power wire and common wire. Observe all
electrical codes
dictating the maximum current allowable for each wire size.
•
If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following:
•Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. To avoid
interference, wires with different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to determine which wires should be kept separate.
The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separated.
•We strongly advise labeling the wiring to all devices in the system.

3
3. Accessing the VPort’s Web-based Manager
This chapter includes information about how to access the VPort 56-2MP IP camera for the first time.
The following topics are covered in this chapter:

Functions Featured on the VPort’s Web Homepage
VPort’s Information
IP Camera Name
Camera Image View
Client Settings
System Configuration
Video Information

VPort 56-2MP Accessing the VPort’s Web-based Manager
3-2
Functions Featured on the VPort’s Web
Homepage
The homepage of the VPort’s web console shows information specific to that VPort, the camera image, and
configurations for the client and server.
NOTE
The VPort’s web homepage is best viewed in 1280 x 1024 screen resolution. We strongly recommend using IE
8
.0 (Microsoft Internet Explorer) or above to avoid incompatibility with the ActiveX Plug-in.
VPort’s Information
This section shows the VPort’s model name, server name, IP address, MAC address, firmware version, and the
display status of the LEDs located on the VPort’s front panel.
NOTE
The VPort LEDs shown on the VPort’s web homepage are updated every 10 seconds.
IP Camera Name
A server name can be assigned to each server. Administrators can change the name in System
Configuration/System/General. The maximum length of the sever name is 40 bytes.
Camera Image View
The assigned image description and system date/time will be displayed in the caption above the image window.
You may disable the caption or change the location of the image information in System
Configuration/Video/Image Setting. Note that if the VPort’s motion detection function is active, some
windows in the video picture might be framed in red.

VPort 56-2MP Accessing the VPort’s Web-based Manager
3-3
Client Settings
Users can configure the following functions in Client Settings.
1. Encoder standard: Shows the encoding algorithm currently being used. VPort 56-2MP features 2 built-in
encode engine to generate a maximum of 3 simultaneous video streams. Each client can select the H.264
video streams from Stream 1, or the MJPEG/ H,264 video stream from Stream 2. To configure these video
streams, please go to:
System Configuration/Video/Video Performance.
2. Protocol Options: Choose one of four protocols to optimize your usage—Multicast (RTSP or Push) or
Unicast (UDP, TCP, HTTP).
•Multicast protocol can be used to send a single video stream to multiple clients. In this case, a lot of
bandwidth can be saved since only one video stream is transmitted over the network. However, the
network gateway (e.g., a switch) must support the multicast protocol (e.g., IGMP snooping). Otherwise,
the multicast video transmission will not be successful.
RTSP: Enables the multicast video stream to be sent in RTSP control, which means the multicast
video stream will be sent only if it receives the client’s request.
Push: Enables the multicast video stream to be sent in Push control, which means that after this
setting is selected the multicast video stream will be sent continuously even without any client
request.
•Unicast protocol is used to send a single video stream to one client.
UDP can be used to produce audio and video streams that are more real-time. However, some
packets may be lost due to network burst traffic, and images may become blurred.
TCP can be used to prevent packet loss, which results in a more accurate video display. The
downside of using TCP is that the real-time delay is worse than with UDP protocol.
HTTP can be used to prevent being blocked by a router’s firewall. The downside of using HTTP is that
the real-time delay is worse than with UDP protocol.
•Network Interface designates the connection interface for multicast video stream selection. The box
lists the current NIC interfaces. Select which NIC interface will receive multicast streams.
Once the IP camera is connected successfully, Protocol Options will indicate the selected protocol. The selected
protocol will be stored on the user’s PC, and will be used for the next connection.
NOTE
For multicast video stream settings, please refer to
System Configuration

Network

Multicast.

VPort 56-2MP Accessing the VPort’s Web-based Manager
3-4
System Configuration
A button or text link on the left side of the system configuration window only appears on the administrator’s
main page. For detailed system configuration instructions, refer to Chapter 4, System Configuration.
Video Information
Users can easily monitor the current video performance by looking at the Video Information shown on the
left side of the homepage. The following properties are shown: Video Size, Video Quality (Fixed bit rate or Fixed
video quality), Max. FPS (frames per second), and (current) FPS Status. Users can select the target camera
image to view each camera’s video performance.
You can open the PTZ control panel from the IP camera home page by clicking “Show PTZ Control Panel.” The
VPort 56-2MP series supports native optical zoom and digital zoom functions, which can be operated from this
panel.

4
4. System Configuration
After installing the hardware, the next step is to configure the VPort 56-2MP’s settings. The web console can be
used for this configuration.
The following topics are covered in this chapter:

System Configuration by Web Console
System
Network
Video
Audio
PTZ
Focus
DynaStreamTM
Alarm

VPort 56-2MP System Configuration
4-2
System Configuration by Web Console
System configuration can be done remotely with Internet Explorer. To access the server, type the system
configuration URL, http://<IP address of Video Server>/overview.asp, to open the configuration main
page.
There are six configuration categories: System, Network, Video, PTZ, D, and Alarm. A description of each
configuration item is shown in the table below:
Category Item Description and Contents
System General Set Host Name and Date/Time
Accounts Administrator, User, and Demo Account Privileges Management
Local Storage
Configure the local storage settings
Diagnosis Self-diagnostic report with system, communication, power, and LED
status
System Log System Log and operation information
System Parameter System parameter information and Import/Export functions
Firmware Upgrade Remote Firmware Upgrade
Factory Default Reset to Factory Default
Reboot Device will reboot to restart the system
Network General The IP network settings of this VPort
SMTP Server Set up Primary and Secondary SMTP Server and e-mail accounts
FTP Server Set up the Primary and Secondary FTP Server
DDNS Configure Dynamic DNS service
Universal PnP Enable UPnP function
Multicast Setting Set up Multicast (IGMP) Streaming
Accessible IP Set up a list to control the access permission of clients by IP address
SNMP Configure the SNMP settings
ToS Configure ToS (Type of Service)
HTTP Event Server Set up the HTTP Event Server to send the event alarm action
Modbus/ TCP Enable Modbus/TCP function
DynaStream Basic Set up the video frame rate change once an alarm or event is
triggered
Conditions
Set up the event/alarm to trigger Dynastream, and the behavior after
being triggered
Video Image Settings Configure the attributes of the video image
Image Tunning Configure the attributes of the camera
ROI
Configure the ROI (region of interest) settings
Privacy Mask Configure the Privacy Mask settings
Camera Modulation Select the camera’s modulation (NTSC or PAL)
Video Performance Set up the Encode Standard (MJPEG or MPEG4), Size (Resolution),
FPS, and Video Quality
Event Alarm Basic General event alarm settings
Schedule Set up the Alarm schedule
Motion Detection Configure the motion detection alarm
Digital Input Configure the Digital Input Alarm
CGI Event Set up the CGI event alarm
Camera Tamper Configure the Camera Tamper event Alarm
This table can also be found on the System Configuration Overview webpage.