Moxa Technologies NPort 6450 Series User manual

– 1 – – 2 – – 3 –
P/N: 1802064500013
NPort 6450 Series
Quick Installation Guide
Sixth Edition, October 2013
Overview
The NPort 6450 secure serial device servers provide reliable
serial-to-Ethernet connectivity for a wide range of serial devices.
The NPort 6450 supports TCP Server, TCP Client, UDP, and
Pair-Connection operation modes to ensure the compatibility of
network software. In addition, the NPort 6450 also supports
Secure TCP Server, Secure TCP Client, Secure Pair-Connection,
and Secure Real COM modes for security critical applications such
as banking, telecom, access control, and remote site
management.
Package Checklist
Before installing the NPort 6450, please verify that the package
contains the following items:
•1 NPort 6450
•Power adaptor
•2 wallmount ears
•Quick installation guide
•Documentation and software CD
•Warranty card
Optional Accessories
•DK-35A: 35 mm DIN-rail mounting kit
•DIN-rail power supply
•CBL-RJ45M9-150: 8-pin RJ45 to male DB9 cable
•CBL-RJ45M25-150: 8-pin RJ45 to male DB25 cable
•NM-TX01: Network module with one 10/100BaseTX Ethernet
port (RJ45 connector; supports cascade redundancy and
RSTP/STP)
•NM-FX01-S-SC/NM-FX01-S-SC-T: Network module with one
100BaseFX single mode fiber port (SC connector; supports
cascade redundancy and RSTP/STP)
•NM-FX02-S-SC/NM-FX02-S-SC-T: Network module with two
100BaseFX single mode fiber ports (SC connectors; supports
cascade redundancy and RSTP/STP)
•NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one
100BaseFX multi mode fiber port (SC connector; supports
cascade redundancy and RSTP/STP)
•NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two
100BaseFX multi mode fiber ports (SC connectors; supports
cascade redundancy and RSTP/STP)
•NM-Modem/NM-Modem-T: One PSTN modem port with RJ11
connector
NOTE
Please notify your sales representative if any of the above
items are missing or damaged.
Hardware Introduction
NOTE
The LCD panel is only available with standard temperature
models.
Reset Button—Press the Reset button continuously for 5 sec to
load factory defaults. Use a pointed object, such as a straightened
paper clip or toothpick, to press the reset button. This will cause
the Ready LED to blink on and off. The factory defaults will be
loaded once the Ready LED stops blinking (after about 5 seconds).
At this point, you should release the reset button.
LED Indicators
Name
Color
Function
PWR
Red
Power is being supplied to the power input.
Ready
Red
Steady on:
NPort is booting up.
Blinking:
IP conflict, DHCP or BOOTP
server problem, or relay output
problem.
Green
Steady on:
Power is on and the NPort 6450
is functioning normally.
Blinking:
NPort is responding to Locate
function.
Off
Power is off, or power error condition exists.
Link
Orange
10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a
short.
P1-P4
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
Serial port is idle.
FX
Orange
Steady on:
Ethernet port is idle.
Blinking:
Fiber port is transmitting or
receiving data.
Alarm
Red
The relay output (DOUT) is open
(exception).
Off
The relay output (DOUT) is shorted (normal
condition).
Module
Green
A network module has been detected.
Off
No network module is present.
Adjustable pull high/low resistor for RS-422/485
(150 KΩor 1 KΩ)
Jumpers are used to set
the pull high/low resistors.
The default is 150 KΩ.
Short the jumpers to set
this value to 1 KΩ. Do not
use the KΩ setting with
RS
-
232 mode, since doing
so will degrade the RS
-
232
signals and shorten the
communication distance.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2013 Moxa Inc. All rights reserved.
Hardware Installation Procedure
STEP 1: Connect the 12-48 VDC power adaptor to the NPort 6450
and then plug the power adaptor into a DC outlet.
STEP 2: For first-time configuration, use a cross-over Ethernet
cable to connect the NPort 6450 directly to your computer’s
Ethernet cable. For connecting to a network, use a standard
straight-through Ethernet cable to connect to a hub or switch.
STEP 3: Connect the NPort 6450’s serial port(s) to serial
device(s).
Placement Options
The NPort 6450 can be placed flat on a desktop or other horizontal
surface. In addition, you may use the DIN-Rail or Wall Mount
options, as illustrated below.
Wallmount
DIN Rail
Software Installation Information
The Document & Software CD contains the User’s Manual, NPort
Search Utility, and the PComm Lite Suite. Insert the CD and follow
the on-screen instructions. Please refer to the User’s Manual for
additional details on using the NPort Search Utility and PComm
Lite.
Pin Assignments and Cable Wiring
RS-232/422/485 Pin Assignments (male DB9)
Pin
RS-232
RS-422
4W-RS-485
2W-RS-485
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Specifications
LAN
Ethernet
10/100 Mbps, RJ45
Protection
Built-in 1.5 KV magnetic isolation
Optical Fiber (for fiber port modules)
Distance
Multi mode:
0 to 2 km, 1310 nm (62.5/125 μm, 500 MHz*km)
Single mode:
0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km)
Min. TX Output
Multi mode: -20 dBm; Single mode: -5 dBm
Max. TX Output
Multi mode: -10 dBm; Single mode: 0 dBm
Sensitivity
Multi mode: -34 to -30 dBm,
Single mode: -36 to -32 dBm
Serial
Interfaces
RS-232/422/485 (male DB9)
No. of Ports
4
Serial Communication Parameters
Parity
None, Even, Odd, Space, Mark
Data Bits
5, 6, 7, 8
Stop Bit(s)
1, 1.5, 2
Flow Control
RTS/CTS, XON/XOFF, DTR/DSR
Speed
50 bps to 921.6 kbps
Additional Features
Console Port
RS-232 (see the user’s manual for detailed
operating instructions)
Memory
One SD socket
Software Features
Protocols
ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP, DDNS, HTTP, SMTP, HTTPS, SSL,
SSH, PPPoE
Utilities
Windows utility for Windows 98, ME, NT, 2000,
XP, 2003, Vista, 8, XP x64, 2003
x64, Vista x64,
2012 x64
Security
DES/3DES/AES
OS Driver
Support
Real COM drivers:
Windows 95, 98, ME, NT, 2000, XP, XP
x64, 2003,
2003 x64, Vista, Vista x64
Real TTY drivers: Linux 2.4, 2.6, and 3.x
Fixed TTY drivers: SCO Unix, SCO
OpenServer 5,
OpenServer 6, UnixWare 7, UnixWare 2.1,
SVR4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD 5,
FreeBSD 6
Configuration
Web Console, Serial/Telnet Console, Windows
utility
Power Requirements
Power Input
12 to 48 VDC
Mechanical Specifications
Material
SECC sheet metal (1 mm)
Environmental Limits
Operating
Temperature
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage
Temperature
-20 to 85°C (-4 to 185°F), 5 to 95% RH
Regulatory Approvals
EMC
FCC Class A, CE Class A
Safety
UL, CUL, TUV