Moxa Technologies NPort W2250A-T-EU User manual

NPort W2150A/W2250A Series
User’s Manual
Version 10.2, July 2020
www.moxa.com/product
© 2020 Moxa Inc. All rights reserved.

NPort W2150A/W2250A Series
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance
with the terms of that agreement.
Copyright Notice
© 2020 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not
limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to
the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility
for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview ...........................................................................................................................................1-2
Package Checklist ...............................................................................................................................1-2
Product Features ................................................................................................................................1-3
Serial Port Pin Assignments..................................................................................................................1-3
2. Getting Started ................................................................................................................................. 2-1
Overview ...........................................................................................................................................2-2
Panel Layout ......................................................................................................................................2-2
LED Indicators....................................................................................................................................2-3
Top Panel LED Indicators..............................................................................................................2-3
End Panel LED Indicators..............................................................................................................2-3
Pull High/Low Resistors for RS-422/485.................................................................................................2-4
Placement Options ..............................................................................................................................2-5
Connecting the Hardware ....................................................................................................................2-5
Connecting to the Network ...........................................................................................................2-6
Connecting the Power ..................................................................................................................2-6
Connecting to a Serial Device .......................................................................................................2-6
3. Initial IP Configuration ..................................................................................................................... 3-1
Overview ...........................................................................................................................................3-2
Factory Default IP Settings ..................................................................................................................3-2
Using ARP to Assign an IP Address........................................................................................................3-2
Using the Telnet Console to an Assign IP Address ...................................................................................3-3
Using the Serial Console to an Assign IP Address ....................................................................................3-6
4. Introduction to Operation Modes ...................................................................................................... 4-1
Overview ...........................................................................................................................................4-2
Real COM Mode ..................................................................................................................................4-2
RFC2217 Mode ...................................................................................................................................4-3
TCP Server Mode ................................................................................................................................4-3
TCP Client Mode .................................................................................................................................4-3
UDP Mode..........................................................................................................................................4-4
Pair Connection Modes ........................................................................................................................4-4
Ethernet Modem Mode.........................................................................................................................4-4
5. Installing and Configuring the Software ........................................................................................... 5-1
Overview ...........................................................................................................................................5-2
Device Search Utility (DSU) .................................................................................................................5-2
Installing the DSU .......................................................................................................................5-2
Finding NPort Device Servers on a Network ....................................................................................5-4
Modifying NPort IP Addresses........................................................................................................5-5
Upgrading NPort Firmware............................................................................................................5-6
NPort Windows Driver Manager ............................................................................................................5-7
Installing NPort Windows Driver Manager .......................................................................................5-7
Adding Mapped Serial Ports ........................................................................................................ 5-10
Configuring Mapped Serial Ports.................................................................................................. 5-13
Command-Line Installation/Removal............................................................................................ 5-17
Linux Real TTY Drivers ...................................................................................................................... 5-19
Basic Steps............................................................................................................................... 5-19
Installing Linux Real TTY Driver Files ........................................................................................... 5-19
Mapping TTY Ports..................................................................................................................... 5-20
Removing Mapped TTY Ports....................................................................................................... 5-20
Removing Linux Driver Files........................................................................................................ 5-21
UNIX Fixed TTY Drivers ..................................................................................................................... 5-21
Installing the UNIX Driver .......................................................................................................... 5-21
Configuring the UNIX Driver ....................................................................................................... 5-22
6. Web Console: Basic Settings ............................................................................................................. 6-1
Overview ...........................................................................................................................................6-2
Basic Settings ....................................................................................................................................6-4
7. Web Console: Network Settings ........................................................................................................ 7-1
Overview ...........................................................................................................................................7-2
Network Settings ................................................................................................................................7-2
General Settings .........................................................................................................................7-2
Ethernet/Bridge Settings ..............................................................................................................7-3
WLAN Settings ............................................................................................................................7-6
Advanced Settings..................................................................................................................... 7-24
8. Web Console: Serial Port Settings ..................................................................................................... 8-1
Overview ...........................................................................................................................................8-2

Serial Port Settings......................................................................................................................8-2
Communication Parameters ........................................................................................................ 8-21
Data Buffering/Log .................................................................................................................... 8-22
9. Web Console: System Management................................................................................................... 9-1
Overview ...........................................................................................................................................9-2
System Management...........................................................................................................................9-2
Misc. Network Settings.................................................................................................................9-2
Auto Warning Settings .................................................................................................................9-6
Maintenance ............................................................................................................................. 9-10
Certificate ................................................................................................................................ 9-14
10. Web Console: System Monitoring .................................................................................................... 10-1
Overview ......................................................................................................................................... 10-2
System Monitoring ............................................................................................................................ 10-2
Serial Status............................................................................................................................. 10-2
System Status .......................................................................................................................... 10-4
11. Web Console: Restart ...................................................................................................................... 11-1
Overview ......................................................................................................................................... 11-2
Restart ............................................................................................................................................ 11-2
Restart System ......................................................................................................................... 11-2
Restart Ports ............................................................................................................................ 11-3
12. Android API Instructions ................................................................................................................ 12-1
Overview ......................................................................................................................................... 12-2
How to Start MxNPortAPI ........................................................................................................... 12-2
MxNPortAPI Function Groups.............................................................................................................. 12-3
Example Program ............................................................................................................................. 12-3
A. SNMP Agents with MIB II & RS-232-Like Groups .............................................................................. A-1
RFC1213 MIB-II Supported SNMP Variables ...........................................................................................A-1
System MIB ................................................................................................................................A-1
Interfaces MIB ............................................................................................................................A-1
IP MIB .......................................................................................................................................A-1
ICMP MIB ...................................................................................................................................A-2
UDP MIB ....................................................................................................................................A-2
Address Translation .....................................................................................................................A-2
TCP MIB .....................................................................................................................................A-2
SNMP MIB ..................................................................................................................................A-2
RFC1317: RS-232 MIB Objects .............................................................................................................A-3
Generic RS-232-like Group ...........................................................................................................A-3
RS-232-like General Port Table .....................................................................................................A-3
RS-232-like Asynchronous Port Group............................................................................................A-3
The Input Signal Table .................................................................................................................A-3
The Output Signal Table...............................................................................................................A-3
B. Well-Known Port Numbers ................................................................................................................ B-1
C. Ethernet Modem Commands.............................................................................................................. C-1
Dial-in Operation ................................................................................................................................C-1
Dial-out .............................................................................................................................................C-1
Disconnection Request from Local Site ..................................................................................................C-1
Disconnection Request from Remote Site...............................................................................................C-1
AT Commands....................................................................................................................................C-2
S Registers ........................................................................................................................................C-3
D. Federal Communication Commission Interference Statement ........................................................... D-1
E. FCC Warning Statement .................................................................................................................... E-1

1
1. Introduction
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Serial Port Pin Assignments

NPort W2150A/W2250A Series Introduction
1-2
Overview
In this chapter, we introduce the basic features and specifications of the NPort W2150A/W2250A and NPort
W2150A/W2250A-T, referred to collectively as the NPort W2150A/W2250A Series.
The NPort W2150A/W2250A Series of wireless device servers are used to connect RS-232/422/485 serial
devices or Ethernet devices, including PLCs, meters, and sensors, to a wireless LAN. Your communications
software will be able to access the serial devices or Ethernet devices from anywhere over a local LAN,
WLAN, or the Internet. Moreover, the WLAN environment offers an excellent solution for applications in
which the serial devices and Ethernet devices are moved frequently from place to place.
The NPort W2150A/W2250A supports both automatic IP configuration protocols (DHCP, BOOTP) and manual
configuration using a standard web browser. Both IP configuration methods ensure quick and effective
installation. In addition, a utility called “NPort Windows Driver Manager” makes port mapping easy.
The external antenna can be adjusted for maximum signal strength. You can also choose to use your own
antenna for additional flexibility and scalability. A signal strength indicator on the front panel makes it easier
for you to troubleshoot any connection problems.
The NPort W2150A/W2250A Series offers different operation modes to ensure compatibility with standard
network APIs, including TCP Server Mode, TCP Client Mode, and UDP Mode. Real COM/TTY drivers are
provided to allow legacy serial-based software to communicate over an IP network instantly. This preserves
your software investment while providing all the advantages of networking your serial devices.
For easier management, the NPort W2150A/W2250A includes features such as password authentication, IP
filtering, 64-bit and 128-bit WEP encryption, and SNMP support.
Package Checklist
Standard Accessories
•1 NPort W2150A or NPort W2250A wireless device server
•1 antenna 2.4/5 GHz: ANT-WDB-ARM-02
•100 to 240 VAC power adapter (excluding T models)*
•1 Ethernet cable: CBL-RJ458P-100
•Quick installation guide (printed)
•Warranty card
NOTE
The package includes one power adapter suitable for your region.
Optional Accessories
•DK35A: DIN-rail mounting kit (35 mm)
•Power-jack-to-terminal-block power cable (P/N: 9199000000900)
NOTE
Please notify your sales representative if any of the above it
ems is missing or damaged.

NPort W2150A/W2250A Series Introduction
1-3
Product Features
•Supports wireless client: links any serial or Ethernet device to an IEEE 802.11a/b/g/n network
•Web-based configuration over Ethernet or WLAN
•Enhanced remote configuration with HTTPS, SSH
•Secure data access with WEP, WPA, WPA2
•Built-in WLAN site survey tool
•Fast Roaming for quick automatic switching between access points
•Per-port offline port buffering and serial data log
•Dual power inputs via power jack and terminal block
Serial Port Pin Assignments
Pin RS-232 RS-422/ RS-485 (4W) RS-485 (2W)
1 DCD TxD-(A) –
2 RXD TxD+(B) –
3 TXD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5 GND GND GND
6 DSR – –
7 RTS – –
8 CTS – –
9 – – –

2
2. Getting Started
The following topics are covered in this chapter:

Overview

Panel Layout

LED Indicators
Top Panel LED Indicators
End Panel LED Indicators

Pull High/Low Resistors for RS-422/485

Placement Options

Connecting the Hardware
Connecting to the Network
Connecting the Power
Connecting to a Serial Device

NPort W2150A/W2250A Series Getting Started
2-2
Overview
This chapter presents the hardware features of the NPort W2150/W2250A Series and explains how to
connect the hardware.
Panel Layout
NPort W2150A/W2150A-T NPort W2250A/W2250A-T

NPort W2150A/W2250A Series Getting Started
2-3
LED Indicators
Top Panel LED Indicators
Name Color Function
Ready
Red
Steady on: Power is on, and the NPort is booting up.
Blinking: An IP conflict exists, or the DHCP/ BOOTP server did not
respond properly.
Green Steady on: The NPort is functioning normally.
Blinking: The unit is responding to Locate function.
Off Power is off, or a power error condition exists.
WLAN Green
Steady on: Wireless enabled
Blinking: The NPort can’t establish WLAN connection with AP
(Infrastructure) or station (Ad-Hoc)
Off Wireless not enabled.
Port 1
Port 2
Orange Serial port is receiving data.
Green Serial port is transmitting data.
Off No data is flowing to or from the serial port.
Signal Strength
(5 LEDS)
Red 1 Red - the signal strength (RSSI) is worse than -88 dBm
2 Red - the signal strength (RSSI) is between -87 to -79 dBm
Green
3 Green - the signal strength (RSSI) is between -78 to -68 dBm
4 Green - the signal strength (RSSI) is between -67 to -60 dBm
5 Green - the signal strength (RSSI) is between -59 to -45 dBm
End Panel LED Indicators
Name Color Function
Ethernet
Orange 10 Mbps Ethernet connection
Green 100 Mbps Ethernet connection
Off Ethernet cable is disconnected

NPort W2150A/W2250A Series Getting Started
2-4
Pull High/Low Resistors for RS-422/485
You may need to set the pull high/low resistors when termination resistors are used for certain RS-422 or
RS-485 environments.
S2 (Port 1)
S3 (Port 2)
DIP 1
Pull high resistor
DIP 2
Pull low resistor
DIP 3
Terminal resistor
DIP 4
Reserved
ON 1 KΩ 1 KΩ 120 Ω –
OFF *150 KΩ *150 KΩ *N/A –
*Default
S3 is for NPort W2250A only
ATTENTION
Do not use the 1 KΩ setting while in RS
-232 mode. Doing so will degrade the RS-
232 signals and reduce the
effective communication distance.

NPort W2150A/W2250A Series Getting Started
2-5
Placement Options
The NPort can be placed on a desktop or other horizontal surface. You can also install the NPort on a DIN-
rail or on the wall.
Wall Mounting DIN-Rail Mounting
Connecting the Hardware
ATTENTION
Before
connecting the hardware, follow these important wiring safety precautions:
Disconnect power source
Do not install or wire this unit or any attached devices with the power connected. Disconnect the power
before installation by removing the power cord before
installing and/or wiring your unit.
Follow maximum current ratings
Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size.
If the current goes abov
e the maximum ratings, the wiring could overheat, causing serious damage to your
equipment.
Use caution
- unit may get hot
The unit will generate heat during operation, and the casing
may be too hot to touch. Take care when
handling
the unit. Be sure to leave adequate space for ventilation.
The following guidelines will help ensure trouble-free signal communication with the NPort.
•Use separate paths to route wiring for power and devices to avoid interference. Do not run signal or
communication wiring and power wiring in the same wire conduit. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.
•If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the
intersection point.
•Keep input wiring and output wiring separate.
•Label all wiring to each device in the system for easier testing and troubleshooting

NPort W2150A/W2250A Series Getting Started
2-6
Connecting to the Network
Use the supplied Ethernet cable to connect the NPort to your Ethernet network. If the cable is properly
connected, the NPort will indicate a valid connection to the Ethernet as follows:
•A green Ethernet LED indicates a valid connection to a 100 Mbps Ethernet network.
•An orange Ethernet LED indicates a valid connection to a 10 Mbps Ethernet network.
•A flashing Ethernet LED indicates that Ethernet packets are being transmitted or received.
Connecting the Power
Connect the VDC power line (12 to 48 V) to the NPort’s power jack or terminal block (recommended for only
one connection at a time). If power is properly connected, the “Ready” LED will initially glow red. When the
system is ready, the “Ready” LED will turn green.
Connecting to a Serial Device
Use a serial cable to connect your serial device to a serial port on the NPort.

3
3. Initial IP Configuration
The following topics are covered in this chapter:

Overview

Factory Default IP Settings

Using ARP to Assign an IP Address

Using the Telnet Console to an Assign IP Address

Using the Serial Console to an Assign IP Address

NPort W2150A/W2250A Series Initial IP Configuration
3-2
Overview
This chapter presents several ways to assign the NPort’s IP address for the first time. Please refer to
Chapter 2 for instructions on connecting to the network.
The web console is the recommended method for configuring the NPort. Please refer to Chapter 5 and 6 for
details on using the web console for configuration.
ATTENTION
The LAN and WLAN interfaces cannot be used at the same time
if you don't enable the Ethernet Bridge
mode (please refer to
Chapter 7 for more details). If the Ethernet link is active, then WLAN connections will
be disabled. If the WLAN connection is active, then the Ethernet link will be disabled.
ATTENTION
Make sure that the Ethernet cable
is connected before powering up the NPort.
Factory Default IP Settings
Network Interface IP Configuration IP Address Netmask
LAN Static 192.168.126.254 255.255.255.0
WLAN Static 192.168.127.254 255.255.255.0
If your NPort is configured to obtain its IP settings from a DHCP or BOOTP server but is unable to get a
response, it will use the factory default IP address and netmask.
ATTENTION
If you forget the IP address of your NPort, you can look it up using the
Device Search Utility (DSU). After
the
Device Search Utility (DSU) has found all NPorts on the network, each unit will be listed with its IP
address. Please refer to Chapter 11 for additional information on using
the Device Search Utility (DSU).
Using ARP to Assign an IP Address
The ARP (Address Resolution Protocol) command can be used to assign an IP address to the NPort. The ARP
command tells your computer to associate the NPort’s MAC address with the specified IP address. You must
then use Telnet to access the NPort, at which point the device server’s IP address will be reconfigured. This
method only works when the NPort is configured with default IP settings.
1. Select a valid IP address for your NPort. Consult with your network administrator if necessary.
2. Obtain the NPort’s MAC address from the label on its bottom panel.
3. From the DOS prompt, execute the arp -s command with the desired IP address and the NPort’s MAC
address, as in the following example:
arp -s 192.168.200.100 00-90-E8-xx-xx-xx
In this example, 192.168.200.100 is the new IP address that will be assigned to the NPort, and 00-90-
E8-xx-xx-xx is the NPort’s MAC address.
4. From the DOS prompt, execute a special Telnet command using port 6000, as in the following example:
telnet 192.168.200.100 6000
In this example, 192.168.200.100 is the new IP address that will be assigned to the NPort.

NPort W2150A/W2250A Series Initial IP Configuration
3-3
5. You will see a message indicating that the connection failed.
The NPort will automatically reboot with the new IP address. You can verify that the configuration was
successful by connecting to the new IP address with Telnet, ping, the web console, or the Device Search
Utility (DSU).
Using the Telnet Console to an Assign IP
Address
1. Select Run… from the Windows Start menu.
2. Enter telnet 192.168.126.254(the NPort’s default IP address) and click [OK].
3. Enter your login account and password, then press ENTER.
(Default login is admin and password is moxa.)

NPort W2150A/W2250A Series Initial IP Configuration
3-4
4. You will login to the Overview page.
5. Press Nor use the cursor keys to select Network and press ENTER.
6. Press Eor use the cursor keys to select Ethernet and press ENTER.

NPort W2150A/W2250A Series Initial IP Configuration
3-5
7. Use the cursor keys to navigate between the different fields. For IP address, Netmask, and Gateway,
enter the desired values directly. For IP configuration and LAN speed, press ENTER to open a
submenu and select between the available options.
8. Press ESC to return to the menu. When prompted, press Yto save the configuration changes.

NPort W2150A/W2250A Series Initial IP Configuration
3-6
The NPort will reboot with the new IP settings. You can telnet to the new IP to login again.
Using the Serial Console to an Assign IP
Address
Before using the NPort’s serial console, turn off the power and use a serial cable to connect the NPort
console port to your computer’s serial port. Port 1 on the NPort serves as the console port. Use Port 1
connecting to the console port with a serial-based terminal or terminal emulator program, such as Windows
HyperTerminal. You may also download PComm Lite at www.moxa.com. The terminal type should be set as
ANSI or VT100, and the serial communication parameters should be set as 19200, 8, N, 1 (19200 for baud
rate, 8 for data bits, None for parity, and 1 for stop bits). As soon as the connection is open, you will be
presented with a text menu displaying the NPort W2150A/W2250A Series general settings. Please refer to
Chapter 4 for a description of the available settings. The following instructions, we recommend using
PComm Terminal Emulator, which can be downloaded free of charge from www.moxa.com, to carry out the
configuration procedure.
1. Connect your PC’s serial port to the NPort’s console port.
2. Open your terminal emulator program, such as Windows HyperTerminal. We recommend using PComm
Terminal Emulator, which can be downloaded for free at www.moxa.com.
3. In your terminal emulator program, configure the communication parameters for the serial port on the
PC. The parameters should be set to 19200 for baud rate, 8for data bits, None for parity, and 1for
stop bits.

NPort W2150A/W2250A Series Initial IP Configuration
3-7
4. In your terminal emulator program, set the terminal type to ANSI or VT100. If you select Dumb
Terminal as the terminal type, some of the console functions—especially the “Monitor” function—may
not work properly.
5. Hold the grave accent key (`) down and power up the NPort.
The continuous string of grave accent characters triggers the NPort to switch from data mode to console
mode.