Mr. Christmas Alexa 68331 User manual

FOR INDOOR USE ONLY
Mr. Christmas
Alexa Compatible LED
Christmas Tree
5ft -Item # 68331 / 68335
6.5ft -Item # 68332 / 68336
Instruction Manual
FOR INDOOR USE ONLY

Before starting assembly, be sure to check all contents
and lay out the various tree parts accordingly.
There are:
Step 1 : Check the contents of your box
A. Top tree section
B. Bottom tree section, includes control box and power cord with adaptor.
C. Tree stand.
D. Three pins for the tree stand.
E. “Ornament” with voice activated command list.
F. Spare bulbs: 5 pieces for 5’ tree, 6 pieces for 6.5’ tree
(in the polybag attached to the end of the light strand inside the tree).
2
E
F
D
C
AB

Step 2 : Expand Stand
1. Take the tree stand and pull apart the legs (Figure A), open to full Position
(Figure B)
2. Take the fully opened tree stand and insert pins into the pre-drilled holes,
tightening the pins part way (complete tightening in Step 3-1).
Figure A Figure B Figure C
3

Step 3-1 : Tree Assembly
Section B
1. Take the tree section labeled “B” and insert
into the top of tree stand.
(Figure A)
2. Fully tighten the 3 pins into place (Figure B).
Secure the tree base firmly to the tree stand.
Figure A
Figure B
4

Step 3-2 : Tree Assembly
Section A
Section B
Take the tree section labeled “A” and insert into the top of the pole of section “B”.
IMPORTANT TREE SET UP TIPS:
1. Shake the tree well after
assembly to ensure the
branches are extended.
2. Some shaping of the
tree may be required for
best appearance.
3. Spare bulbs are
included in a small bag
inside the tree. Remove
from the tree and keep
in case replacement is
needed.
5

Step 4 : Connect to AC Power
Attach the power cord with adaptor to the control box, plug the adaptor into
an AC power source.
6

Figure A
7
Barcode Scanning & Location
Note that during device setup
you may be asked to scan a
device barcode.You can find this
on the back of the controller,
shown in Figure A.
Step 5: Connect to Alexa
1. Download the “Amazon Alexa” application from the app store on your mobile
device .
2. Install and open the “Amazon Alexa” application.
3. Go to the settings menu.
4. Select “Add Device”
5. Select “Christmas Tree” and follow the on-screen instructions.
6. To set up a second tree, select “Second Christmas Tree” and follow the instructions.
Alexa will ask for clarification if a command does not target a specific tree.

Step 6-A: Change your Christmas Tree LED lighting Mode using Alexa
8
Follow the voice commands for a list
of functions to achieve up to 10
lighting functions.
Figure A
Color options
Command –“Set Christmas tree to” :
1. White
2. Multi-color
Pattern functions
Command –“Set Christmas tree to” :
a. Steady
b. Fade
c. Cascade
d. Waterfall
e. Morph
f. Flip
Brightness Options
Command –“Set Christmas tree to” :
a. High
b. Medium
c. Low
Refer page 11-14 for examples of commands.

Step 6-B : Manually change your Christmas Tree LED lighting mode
Push Button on Control Box to switch Christmas Tree LED Light Mode.
The order of each button is as follows :
9
Demo Mode : The Demo mode will start
and play all 12 lighting functions every
15 seconds.
1. Power On-Demo Mode
2. White Steady
3. Multi-color Steady
4. White Fade
5. Multi-color Fade
6. White Cascade
7. Multi-color Cascade
8. White Waterfall
9. Multi-color Waterfall
10. White Morph
11. Multi-color Morph
12. White Flip
13. Multi-color Flip
14. Power Off

Step 6-C : Automate your Christmas Tree with Routines
Alexa Routines allow you to automate your Christmas Tree Functionality. With Routines,
you can turn your tree on with custom commands (i.e. Good Morning) or turn the tree
on/off at scheduled times (i.e. every day at 10AM)
How to Enable Routines with Alexa.
1. Open the Alexa app.
2. Go to the menu and select “Routines”
3. Select Plus
4. Select “When this happens”, and then choose how to begin your Routine
(i.e. “Good Morning, or a scheduled time).
5. Select “Add Action”, select “Smart Home”, and then select “Christmas Tree”.
Configure the desired LED lighting mode for your selected action.
10

Example 1 ：Turn Christmas Tree on
“Turn Christmas Tree ON”
11
Example 2 ：Set lighting mode to Multi-color
“Set Christmas Tree to : Multi-color”

12
Example 3 ：Set lighting mode to Fade
“Set Christmas Tree to : Fade”
Example 4 ：Set lighting mode to Low
“Set Christmas Tree to : Low”

13
Example 5 ：Set lighting mode to Demo mode
“Turn Christmas Tree DEMO ON”
Example 4 ：Turn Christmas Tree off
“Turn Christmas Tree OFF”

Example 5 ：Turn Christmas Tree on with Routine
14
“Good Morning / Good Night”

1. I can’t connect my device to Alexa.
•Check that your Alexa device and the Alexa app have the latest software
version.
•Make sure that your Alexa device and the light strand are connected to the
same Wi-Fi network.
•Check that your device is within 30 ft. (9 m) of the light strand.
•Try setting your Christmas Tree LED light Mode to “STEADY” and then proceed
with the pairing process.
•Perform afactory reset : Press and hold the button on the control box of the
tree for 10-11 seconds. The tree lights will flash white 3times. This indicates
that the instructions were received. Follow the instructions on page 7to set
up your device with Alexa app.
2. I can’t get the light strand barcode to successfully scan.
•During the Alexa mobile app setup process, select “Don’t Have aBarcode”
•Follow the on-screen instructions.
3. My Light Strand stopped working with Alexa.
•Try apower cycle:Unplug your Christmas Tree from the outlet, and then plug
it back in.
•Perform afactory reset : Press and hold the button on the control box of the
tree for 10-11 seconds. The tree lights will flash white 3times. This indicates
that the instructions were received. Follow the instructions on page 7to set
up your device with Alexa app.
Connectivity Troubleshooting
Common connectivity troubleshooting steps.
15

User Servicing Instructions
Replace the bulb.
1. Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
2. Pull bulb and plastic base straight out of bulb holder
3. Replace bulb with only 3 Volt 0 , 06 Watt LED type bulb
(provided with product).
If the new bulb base does not fit in bulb holder, follow the
steps below before step 3.
a) Remove the base of burned out bulb by straightening bulb
leads and gently pull bulb out.
b) Thread leads of new bulb through holes In old base with
one lead in each hole.
c) After bulb is fully inserted into base, bend each lead up
like other bulbs in the light set. so that the leads will touch
the contacts inside the bulb holder.
When using electrical products, basic precautions should
always be followed including the Following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided contact a qualified for proper installation.
c) This seasonal use product is not intended for permanent
Installation or use.
d) Do not mount or place near gas or electric heaters, fireplace,
candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails,
or place on sharp hooks or nails.
f) Do not let bulbs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring
for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire,
burns, personal injury and electric shock it should not be
played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or
light string.
k) Do not close doors or windows on the product or extension
cords as this may damage the wire insulation
l) Do not cover the product with cloth, paper or any material
not part of the product when In use.
m)This product is equipped with push-in type bulbs. Do not
twist bulbs.
n) Read and follow a instructions that are on the product or
provided with the product.
o) Save these instructions.
CAUTION
1. To reduce the risk of fire or electric shock do not attempt to
replace bulbs or modify string.
2. To reduce the risk of fire and electric shock：a) Do not install
on trees having needles, leaves or branch coverings of metal
or materials which look like metal, and b) Do not mount or
support strings in a manner that can cut or damage wire
insulation.
Made in China
Model No : 68331 / 68332 / 68335 / 68336
Made by Mr. Christmas Inc.
[e-mail]
Customer Service Phone: [phone]
IMPORTANT SAFETY INSTRUCTIONS
16