MSC 96M5985o User manual

96M5985o
Intel®SandyBridge / PCH
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0

ii
96M5985o User’s Manual
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® Sandy Bridge DC Mobile Processor are registered
trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics Corporation.
All other product names or trademarks are properties of their
respective owners.

96M5985o User’s Manual iii
Table of Contents
Introduction.......................................................1
Product Description ............................................................. 1
Checklist .............................................................................. 2
96M5985o Specifications ................................................... 3
Board Dimensions ............................................................... 5
Installations.......................................................6
Installing the CPU ............................................................... 7
Installing the Memory ......................................................... 8
Setting the Jumpers ............................................................. 9
Connectors on 96M5985o .................................................. 13
BIOS Setup.......................................................22
Drivers Installation......................................51
Intel Chipset Software Installation Utility......................... 52
VGA Drivers Installation .................................................. 53
Realtek HD Audio Driver Installation ............................... 54
LAN Drivers Installation ................................................... 55
Intel® Management Engine Interface ............................... 57
ASMedia USB 3.0 Drivers ................................................ 59
Appendix...........................................................60
A. I/O Port Address Map ................................................... 60
B. Interrupt Request Lines (IRQ) ...................................... 61
C. Watchdog Timer Configuration .................................... 62

iv
96M5985o User’s Manual
This page is intentionally left blank.

INTRODUCTION
96M5985o User’s Manual 1
Introduction
Product Description
The 96M5985o Mini ITX motherboard is based on the latest Intel®
QM67 chipset. The platform supports 2nd generation Intel® Core pro-
cessor family with rPGA988B packing and features an integrated dual-
channel DDR3 memory controller as well as a graphics core.
The latest Intel® processors provide advanced performance in both
computing and graphics quality. This meets the requirement of
customers in the gaming, POS, digital signage and server market
segment.
The Intel® QM67 is made with 32 nanometer technology that supports
Intel’s first processor architecture to unite the CPU and the graphics core
on the transistor level. The 96M5985o Mini ITX board utilizes the
dramatic increase in performance provided by this Intel’s latest cutting-
edge technology. Measuring 170mm x 170mm, 96M5985o offers fast
6Gbps SATA support (2 ports), USB3.0 (2 ports) and interfaces for
DVI-D, DVI-I, LVDS and HDMI displays. 96M5985o features Intel
Active Management Technology 7.0.
96M5985o FEATURES:
•Supports Intel® 2nd Generation Core i7/i5/i3 QC/DC mobile
processors
•Two DDR3 SoDIMM, 1066/1333MHz, Max. 8GB memory
•Dual Intel® PCI-Express Gigabit LAN
•Integrated Graphics for DVI-I, DVI-D/HDMI/LVDS displays
•4x SATA 2.0, 2x SATA 3.0, 8x USB 2.0, USB 3.0 (2 ports),
4x COM, Watchdog timer
•1x PCI-E (x16), 1x Mini PCI-E
•Optional AMT

INTRODUCTION
2
96M5985o User’s Manual
Checklist
Your 96M5985o package should include the items listed below.
•The 96M5985o Mini-ITX motherboard
•This User’s Manual
•1 CD containing chipset drivers and flash memory utility
•Serial ATA cable

INTRODUCTION
96M5985o User’s Manual 3
96M5985o Specifications
Product Name 96M5985o
Form Factor Mini-ITX
CPU Type - Intel® 2nd generation CoreTM i7/i5/i3 QC/DC mobile processor
- rPGA package, 37.5 x 37.5 mm
- TDP: QC = 45W~ 55W/ DC = 35W
**Sandy Bridge CPU is NOT socket compatible with Arrandale
CPU Speed Up to 2.7GHz
Cache Up to 8MB
CPU Socket rPGA 988B
Chipset Intel® QM67 PCH; 25 x 27 mm package size
BIOS AMI BIOS, support ACPI Function
Memory Intel® 2nd generation CoreTM i7/i5/i3 QC/DC mobile processor integrated memory
controller
DDRIII 1067/1333 MHz
- SO-DIMM x 2(w/o ECC), Max. 8GB
VGA - Intel® 2nd generation CoreTM i7/i5/i3 mobile processor integrated Gfx
•DVI-I X 1 (thru Level shifter ASM1442)
•DVI-D X 1 (thru Level shifter ASM1442)
•HDMI X 1 (thru Level shifter ASM1442)
•LVDS : DF13 x 2 for supporting dual channel 24-bit
LAN 1. Intel®Lewisville 82579LM GbE PHY
or 82579V GbE PHY
2. Intel® 82583V as 2nd GbE
USB USB 2.0 host controller, supports 8 ports w/ two EHCI, 7 UHCI controllers
Integrated USB 2.0 Rate Matching Hub.
- 4 ports in the rear panel
- Others reserved for onboard pin header ( 4 ports, 2.54mm pitch)
USB 3.0 host controller [ASMedia # ASM1042], support 2 ports
- 2 ports in the rear panel
Serial ATA Intel® QM67 PCH built-in SATA controller, supports total6 ports
2 x SATA (3.0) 6Gbps+ 4 x SATA (2.0) 3Gbps ports (2 FIS based Port Multiplier)
Audio Intel® QM67 PCH built-in High Definition Audio controller+ ALC892 w/ 7.1 CH
LPC I/O Fintek F81865-I (Ver. C)
COM1 (RS232/422/485), COM2/COM3/COM4 (RS232), Hardware
Monitor (2 thermal inputs,4 voltage monitor inputs & 2 fan headers) [CPU FAN
controllabl, but not the system fan]
COM1/2 with pin-9 with power for 2 ports (500 mA for each port)
Digital IO 4 in & 4 out
IAMT(7.0) Intel® QM67 PCH built-in
- Intel® Active Management Technology ver. 7.0
Expansion
Slots - PCI-Express (16x) *1 [PEG]
- Mini PCI-Express (1x) *1 @ Solder side
[Reserved mounting holes for Half-sized also]
Edge
Connector: DVI-D + DVI-I stack connector; Dual DB9 stack connector for COM #1, #2
Dual USB(3.0) dual stack connector; HDMI stack connector
Gbit LAN RJ-45 + dual USB(2.0) stack connector x2
RCA Jack 3x1 for HD Audio
Onboard
Header/
Connector
2 ports x SATA III [Blue color]; 4 ports x SATA II
2x5 pin-header x2 for 4 ports USB; 2x5 pin-header for front panel audio
2x10 pin-header for COM3 (RS232) & COM4 (RS232)
2x5 pin-header for Digital IO; 4-pin box header for LCD backlight control
Watchdog Timer Yes (256 segments, 0, 1, 2…255 sec/min)
System
Voltage ATX
Others LAN Wakeup, EuP/ErP feature (Fintek F75160), UL 60950-1 2nd Edition
compatible

INTRODUCTION
4
96M5985o User’s Manual
Board Size 170mm x 170mm

INTRODUCTION
[
Board Dimensions
96M5985o User’s Manual 5

INSTALLATIONS
6
96M5985o User’s Manual
Installations
This section provides information on how to use the jumpers and
connectors on the 96M5985o in order to set up a workable system. The
topics covered are:
Installing the CPU .................................................................................. 7
Installing the Memory ............................................................................ 8
Setting the Jumpers ................................................................................ 9
Connectors on 96M5985o .................................................................... 13

INSTALLATIONS
Installing the CPU
The 96M5985o board supports rPGA988B socket for Intel® Sandy Bridge
Dual Core mobile processors.
The processor socket comes with a screw to secure the processor. As
shown in the left picture below, loosen the screw first before inserting
the processor. Place the processor into the socket by making sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slide into the socket, fasten the
screw. Refer to the figures below.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
96M5985o User’s Manual 7

INSTALLATIONS
Installing the Memory
The 96M5985o board supports two DDR3 memory socket for a maximum
total memory of 8GB in DDR3 SO-DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1.Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2.Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3.To remove the DDR3 module, press the clips with both hands.
8
96M5985o User’s Manual
DDR3 Module
Lock
Lock Lock
Lock

INSTALLATIONS
96M5985o User’s Manual 9
Setting the Jumpers
Jumpers are used on 96M5985o to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on 96M5985o and their respective functions.
Jumper Locations on 96M5985o ......................................................... 10
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection .................... 11
JP5: COM1 RS232 RI/+5V/+12V Power Setting ............................... 11
JP6: COM2 RS232 RI/+5V/+12V Power Setting ............................... 11
J10: LCD Panel Power Selection ......................................................... 12
J14: Flash Descriptor Security Overide (Factory use only) ................. 12
J22: Clear ME Contents ....................................................................... 12
J23: Clear CMOS Contents ................................................................. 12

INSTALLATIONS
Jumper Locations on 96M5985o
Jumpers on 96M5985o ........................................................................... Page
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection ..................... 11
JP5: COM1 RS232 RI/+5V/+12V Power Setting ................................ 11
JP6: COM2 RS232 RI/+5V/+12V Power Setting ................................ 11
J10: LCD Panel Power Selection ......................................................... 12
J14: Flash Descriptor Security Overide (Factory use only) ................. 12
J22: Clear ME Contents ....................................................................... 12
J23: Clear CMOS Contents .................................................................. 12
10
96M5985o User’s Manual

INSTALLATIONS
JP2, JP3, JP4: RS232/RS422/RS485 (COM1) Selection
COM1
Function RS-232 RS-422 RS-485
Jumper
Setting
(pin closed)
JP2:
3-5&4-6
JP3:
1-2
JP4:
3-5 & 4-6
JP2:
1-3&2-4
JP3:
3-4
JP4:
1-3 & 2-4
JP2:
1-3&2-4
JP3:
5-6
JP4:
1-3 & 2-4
JP5: COM1 RS232 RI/+5V/+12V Power Setting
JP5 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed RI
Pin 5-6
Short/Closed +5V
JP6: COM2 RS232 RI/+5V/+12V Power Setting
JP6 Setting Function
Pin 1-2
Short/Closed +12V
Pin 3-4
Short/Closed RI
Pin 5-6
Short/Closed
+5V
96M5985o User’s Manual 11

INSTALLATIONS
J10: LCD Panel Power Selection
J10 LCD Panel Power
3.3V
5V
J14: Flash Descriptor Security Overide (Factory use only)
J14 Flash Descriptor
Security Overide
OpenDisabled
(Default)
Close Enabled
J22: Clear ME Contents
J22 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear ME
J23: Clear CMOS Contents
J23 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear CMOS
12
96M5985o User’s Manual

INSTALLATIONS
96M5985o User’s Manual 13
Connectors on 96M5985o
Connector Locations on 96M5985o .................................................... 14
CN1: COM1 and COM2 Serial Ports .................................................. 15
CN2: DVI-D and DVI-I Connector ..................................................... 15
CN3: USB3.0 Connector .................................................................... 16
CN4: HDMI Connector ....................................................................... 16
CN5: Gigabit LAN (Intel 82579LM) + USB 2/3 ................................ 16
CN8: Gigabit LAN (Intel 82583V) + USB 0/1 ................................... 16
CN11: HD Audio Connector ............................................................... 16
J1: Digital I/O ...................................................................................... 17
J3: ATX Power Supply Connector ...................................................... 17
J2, J4: COM3, COM4 RS232 Serial Ports .......................................... 17
J6: ATX 12V Power Connector .......................................................... 17
JP8, JP7: LVDS Connectors (1st channel, 2nd channel) ..................... 18
JP9: LCD Backlight Connector ........................................................... 18
JP10, JP11: USB Connectors .............................................................. 18
JP13: SPDIF I/O .................................................................................. 18
J24: Audio Pin Header for Chassis Front Panel .................................. 19
J26: Front Panel Connector ................................................................. 19
CN6, CN7, CN9, CN10, CN12, CN13: SATA Connectors ................ 19
CPU_FAN1: CPU Fan Power Connector ............................................ 19
SYS_FAN1: System Fan1 Power Connector ...................................... 19
JP1: LPC Debug Connector (Factory use only) .................................. 20
J11: Mini-PCIE Connector .................................................................. 20
JP12: SPI Flash Connector (Factory use only) .................................... 20

INSTALLATIONS
Connector Locations on 96M5985o
14
96M5985o User’s Manual

INSTALLATIONS
CN1: COM1 and COM2 Serial Ports
[ Pin # Signal Name
RS-232R2-422 RS-485
1 DCD TX- DATA-
2 RX TX+ DATA+
3 TX RX+ NC
4 DTR RX- NC
5 Ground Ground Ground
6 DSR NC NC
7 RTS NC NC
8 CTS NC NC
9 RI NC NC
10 NC NC NC
CN2: DVI-D and DVI-I Connector
Signal Name Pin # Pin # Signal Name
DATA 2- 1 16 HOT POWER
DATA 2+ 2 17 DATA 0-
Shield 2/4 3 18 DATA 0+
DATA 4- 4 19 SHIELD 0/5
DATA 4+ 5 20 DATA 5-
DDC CLOCK 6 21 DATA 5+
DDC DATA 7 22 SHIELD CLK
N.C 8 23 CLOCK -
DATA 1- 9 24 CLOCK +
DATA 1+ 10 C1 N.C
SHIELD 1/3 11 C2 N.C
DATA 3- 12 C3 N.C
DATA 3+ 13 C4 N.C
DDC POWER 14 C5 A GROUND2
A GROUND 1 15 C6 A GROUND3
96M5985o User’s Manual 15

INSTALLATIONS
16
96M5985o User’s Manual
[ Signal Name Pin # Pin # Signal Name
DATA 2- 1 16 HOT POWER
DATA 2+ 2 17 DATA 0-
Shield 2/4 3 18 DATA 0+
DATA 4- 4 19 SHIELD 0/5
DATA 4+ 5 20 DATA 5-
DDC CLOCK 6 21 DATA 5+
DDC DATA 7 22 SHIELD CLK
N.C 8 23 CLOCK -
DATA 1- 9 24 CLOCK +
DATA 1+ 10 C1 N.C.
SHIELD 1/3 11 C2 N.C.
DATA 3- 12 C3 N.C.
DATA 3+ 13 C4 N.C.
DDC POWER 14 C5 N.C.
A GROUND 1 15 C6 N.C.
CN3: USB3.0 Connector
CN4: HDMI Connector
CN5: Gigabit LAN (Intel 82579LM) + USB 2/3
CN8: Gigabit LAN (Intel 82583V) + USB 0/1
CN11: HD Audio Connector