MSI CX600 User manual

CX600 (MS-1682) Disassemble Guide
■ 1、BATTERY PACK
■ 2、BOTTOM DOOR ASSY
■3、HDD MODULE
■4、ODD MODULE
■5、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
■ 6、KEYBOARD
■ 7、SEPARATE UPPER CASE AND LOWER CASE
■ 8、LOWER CASE ASSY
■9、UPPER CASE ASSY
■10、LCD MODULE ASSY

CX600（MS-1682）Disassemble Guide
1、BATTERY PACK
1.1：Move the “Unlock’ button base on left picture
shows;
1.2：Release the “Release” button and move the
battery pack base on left picture.
Component P/N Qty
Battery Pack S9N-2062200-CE1 1

CX600（MS-1682）Disassemble Guide
2、BOTTOM DOOR ASSY
2.1：Remove the 4 screws (M2.5*5mm),
then remove the Bottom door.
Attention: the screw driver touque is: 2.0-2.5Kgf-cm
Component P/N Qty
Bottom door 307-681J211-Y31 1
Screw E43-1255007-H29 4

CX600（MS-1682）Disassemble Guide
3、HDD MODULE
3.1：Remove the 2 screws(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 2
3.2：Remove the HDD Module according to the
direction as pic shows;

CX600（MS-1682）Disassemble Guide
3、HDD MODULE
3.3：Remove the 2 screws(M3*3.5mm)
that stabilize the bracket;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1303501-H29 2
3.4：Remove the HDD bracket;
Component P/N Qty
HDD Bracket 307-6810111-A89 1
HDD Module S71-2425521-W36 1

CX600（MS-1682）Disassemble Guide
4、ODD MODULE
4.1：Remove the 1 screw(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 1
4.2：Remove the ODD Module according to the
direction as pic shows;

CX600（MS-1682）Disassemble Guide
4、ODD MODULE
4.3：Remove ODD Bezel as below.
Component P/N Qty
ODD Bezel E2P-681F211-Y31 1
4.4：Remove 2pcs M2*3mm Screws Then remove
ODD Bracket as below;
Component P/N Qty
Screw E43-1203003-H29 2
ODD Bracket E2M-6510211-Y28 1
ODD Module S7D-2270015-H44 1

CX600（MS-1682）Disassemble Guide
5、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
5.1:Remove the 6 screws(M2.5*5mm) and FAN
cable, after that remove the Fansink
Attention：the screw driver torque is 2.0-2.2Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 6
Fansink E32-0800220-F05 1
5.2：Open the CPU Slot with Screw Driver, then
remove CPU Module as below.
Component P/N Qty
CPU A09-21201G6-I06 1
5.3：Push the two side shielding of RAM as pic
shows;
2
36
5
1
4

CX600（MS-1682）Disassemble Guide
5、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
5.4：Then remove the RAM module according the
direction as pic shows;
Component P/N Qty
RAM Module S7C-S357701-T10 1
5.5：Remove one screw(M2*3mm); then remove
the two side wireless card antenna as pic shows:
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 1
5.6：Remove the WLAN module according to the
direction of pic shows;
Component P/N Qty
WLAN Module S57-0800290-T46 1

CX600（MS-1682）Disassemble Guide
6、KEYBOARD
6.1：Before remove K/B, firstly remove the
Hinge Cover;
Component P/N Qty
Hinge Cover 307-682E221-Y31 1
6.2：Remove the 5 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 5
6.3 ：Firstly push connector according to the
direction as pic shows; then remove the cable;
Component P/N Qty
Keyboard S1N-3UUS1B1-C54 1

CX600（MS-1682）Disassemble Guide
7、SEPARATE UPPER CASE AND LOWER CASE
7.1：Remove the 2 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Launch board 607-1682B-01S 1
Screw E43-1203003-H29 2
7.2：First release the connector that stabilize the
cable, then remove Launch board according to the
direction that pic shows;

CX600（MS-1682）Disassemble Guide
7、SEPARATE UPPER CASE AND LOWER CASE
7.3：Remove the 2 screws(M2*3mm) that stabilize
the hinge Cap
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 2
7.4 ：Remove the 4 screws(M2.5*5mm) that
stabilize the hinge
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4

CX600（MS-1682）Disassemble Guide
7、SEPARATE UPPER CASE AND LOWER CASE
7.5：Remove the LVDS cable as pic shows:
7.6：Remove the Touchpad cable.
7.7：Remove the 2 screws(M2*3mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
MODEM S52-2801180-C59 1
Screw E43-1203003-H29 2

CX600（MS-1682）Disassemble Guide
7、SEPARATE UPPER CASE AND LOWER CASE
7.8：Remove 5 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 5
7.9：Remove 8 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 8
7.10：Remove the 4 screws (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4

CX600（MS-1682）Disassemble Guide
8、LOWER CASE ASSY
8.1：Remove the USB board cable as left pic
shows:
Component P/N Qty
USB board FPC K1C-1012039-J36 1
8.2：Remove the 1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
USB board 607-1682A-01S 1
Screw E43-1255007-H29 1

CX600（MS-1682）Disassemble Guide
8、LOWER CASE ASSY
8.3：Remove the B/T module;
Component P/N Qty
Bluetooth Module 605-6837D-160 1
8.4：Remove the 1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
8.5：Remove the main board from Lower case;
Component P/N Qty
Main Board 607-16821-01S 1

CX600（MS-1682）Disassemble Guide
8、LOWER CASE ASSY
8.6：Remove the RJ11 from Lower case;
Component P/N Qty
RJ11 CABLE K10-3002131-V03 1
8.7：Remove the 4 screws (M2*3mm), then remove
the Speaker module from lower case;
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 4
Speaker Module S33-A020310-F33 1
Lower Case 307-681D221-Y31 1

CX600（MS-1682）Disassemble Guide
9、UPPER CASE ASSY
9.1：Remove the T/P module,
Component P/N Qty
Touchpad Module S78-3700360-SD2 1
Upper Case 307-682C111-TC7 1
9.2：Release the connector that stabilize the T/P
cable, then remove the T/P module FFC according
to direction of left pic shows;
Component P/N Qty
FFC Cable (To MB) K1C-1012040-J36 1

CX600（MS-1682）Disassemble Guide
10、LCD MODULE ASSY
10.1：Remove the 8 cover rubber
Component P/N Qty
UP Rubber E2Y-6810111-Y40 4
DOWN Rubber E2Y-6740611-Y40 4
10.2：Remove the 4screw (M2.5*5mm). When
removing the LCD bezel, should begin from the
two sides, then the upside to downside;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
LCD Bezel 307-681B211-Y31 1

CX600（MS-1682）Disassemble Guide
10、LCD MODULE ASSY
10.3：Remove the 3 magnet on LCD cover;
Component P/N Qty
LCD Cover Magnet E2Y-2210512-SF7 2
LCD Cover Magnet E2Y-6710411-SF7 1
10.4：Remove INVERTER
Component P/N Qty
INVERTER S78-3300470-SG3 1
10.5：Remove the 6 screws (M2.5*5mm); Remove
the two LCD hinges on two sides;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 6
Hinge R E2M-6810411-G60 1
Hinge L E2M-6810511-G60 1