MSI GX70 Installation instructions

GX70 (MS-176K) Disassembly Guide
■1、BATTERYPACK
■2、ODDMODULE
■3、BOTTOMDOORASSY
■4、HDD MODULE
■5、THERMAL-KIT、CPU、DRAM、SSD CARD ANDSATABOARD
■6、SEPARATEUPPERCASEAND LOWERCASE
■7、LOWERCASEASSY
■8、UPPERCASEASSY
■9、LCDMODULE ASSY

GX70（MS-176K）Disassembly Guide
■1、BATTERYPACK
1.1：Move the “Unlock’ button base on left picture
shows.
1.2：Release the “Release” button and move the
battery pack base on left picture.
 mponent
P/N
Qty
Battery Pack
S9N-3496200-M47
1

GX70（MS-176K）Disassembly Guide
■2、ODD MODULE
2.1：Remove the 1 screws (M2.5*7mm) Then Remove
the ODD Module according to the direction as pic
shows.
Component
P/N
Qty
screw
E43-1257002-G68
1
2.2：Remove ODD Bezel as below.
Coponent
P/N
Qty
ODD Bezel
307-762F211-Y31
1
2.3：Remove 2 Screws (M2*3mm); Then remove ODD
Bracket as below.
Attention：the screw driver torque is 1.0-1.5Kgf-cm
Component
P/N
Qty
Screw
E43-1203003-H29
2
ODD Bracket
E2M-7611311-C22
1
ODD Module
S7D-2270066-H44
1

GX70（MS-176K）Disassembly Guide
■3、BOTTOM DOOR ASSY
3.1：Remove the 7 screws (M2.5*7mm). Then
remove the Bottom door.
Attention: the screw driver touque is: 1.8-2.2 gf-cm
Component
P/N
Qty
Bottom door
307-761J213-Y31
1
Screw
E43-1257002-G68
7

GX70（MS-176K）Disassembly Guide
■4、HDD MODULE
4.1: Remove the 2 screws (M2.5*5mm); then remove
the HDD Module according to the direction as pic
shows.
Attention: the screw driver torque is 1.8-2.2Kgf-cm
Component
P/
Qty
Screw
E43-1255002-G68
2
4.2: Remove the 2 screws (M3*4mm) that stabilize the
HDD brackets, then remove the HDD bracket.
Attention: the screw driver torque is 1.8-2.2Kgf-cm
Component
P/N
Qty
Screw
E43-1304009-G68
2
HDD Bracket
307-6F10112-C22
1
HDD Module
S71-2475702-W36
1

GX70（MS-176K）Disassembly Guide
■5、THERMAL-KIT、CPU AND DRAM
5.1:Remove the 1 screw(M2.5*5mm) and FAN
cable, after that remove the Fan.
Attention：the screw driver torque is 1.8-2.2Kgf-cm
Component
P/N
Qty
Screw
E43-1255002-G68
1
FAN
E33-0800183-MC2
1
5.2: Remove the 3 screws (M2.5*5mm) and 4
spring screws, after that remove the two Heatsink.
Attention：the screw driver torque is 1.8-2.2Kgf-cm
Component
P/N
Qty
Screw
E43-1255002-G68
3
Heatsink
E31-0406091-Y31
1
Heatsink
E31-0803750-Y31
1
5.3：Open the CPU Slot with Screw Driver, then
remove CPU Module as below.
Component
P/N
Qty
CPU
A10-K103506-A08
1
2
1
3

GX70（MS-176K）Disassembly Guide
■5、THERMAL-KIT、CPU AND DRAM
5.4：Push the two side shielding of DRAM as pic
shows; Then remove the DRAM Module according
the direction as pic shows.
Component
P/N
Qty
DRAM Module
S7C-S48A501-A97
2
5.5：Remove 1 screw (M2.5*5mm); then remove
the VGA card as pic shows.
Attention: the screw driver torque is: 1.8-2.2Kgf-cm
Component
P/N
Qty
VGA Card
607-1W0D1-01S
1
Screw
E43-1255002-G68
1
5.6：Remove 2 screws(M2*4m); then remove the
HDD2 Board.
Attention: the screw driver torque is: 1.2-1.6Kgf-cm
Component
P/N
Qty
HDD2 Board
607-176KD-01S
1
Screw
E43-1204002-G68
2

GX70（MS-176K）Disassembly Guide
■6、SEPARATE UPPER CASE AND LOWER CASE
6.1：Before remove K/B, firstly remove the Middle
Cover. Care the Sensor board FPC below the
cover.
Component
P/N
Qty
Middle Cover
307-761E213-Y31
1
6.2：Remove the Sensor board.
Component
P/N
Qty
Sensor Board
607-17622-01S
1
6.3：Remove 1 screw(M2*3mm),then remove the
wlan Antenna and wlan card.
Attention: the screw driver torque is: 1.2-1.6Kgf-cm
Component
P/N
Qty
WLAN Module
S57-08000J0-T46
1
Screw
E43-1203003-H29
1

GX70（MS-176K）Disassembly Guide
■6、SEPARATE UPPER CASE AND LOWER CASE
6.4：Remove the left and right hinge caps.
Component
P/N
Qty
Left Hinge cap
E2P-7610223-Y31
1
Right Hinge cap
E2P-7610323-Y31
1
6.5：Remove the LVDS cable as pic shows.
6.6：Remove MIC cable.
MIC Cable

GX70（MS-176K）Disassembly Guide
■6、SEPARATE UPPER CASE AND LOWER CASE
6.7：Remove the 2 screws (M2.5*7mm) that stabilize
the right LCD hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component
P/N
Qty
Screw
E43-1257002-G68
2
R-Hinge
E2M-7610412-G60
1
6.8 ：Remove the 2screws (M2.5*7mm) that
stabilize the left LCD hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component
P/N
Qty
Screw
E43-1257002-G68
2
L-Hinge
E2M-7610512-G60
1
6.9：Remove the 5 screws (M2*4mm) that stabilize the
keyboard. Then remove the Keyboard.
Attention: the screw driver torque is 1.2-1.6Kgf-cm
Component
P/N
Qty
Screw
E43-1204002-G68
5