MSTRONIC MSE PSE-SW5G User manual

USER’S MANUAL
MSTRONIC CO., LTD.
PSE-SW5G
5 Port PoE Switch & Extender
(Repeat Ethernet and PoE)

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators.......................................................................................
Power Wiring ........................................................................................
Ethernet Port Wiring..............................................................................
PD Port Wiring......................................................................................
Network A lication……………………………………............................
3. Model Information...........................................................
4. Technical Specification........................................................
3
3
3
6
9
11
12
12
13

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
3
1. General Information
The PSE-SW5G PoE (Power Over Ethernet) Switch family provides four 0M/ 00M/ 000M TX
ports with PoE PSE function plus one 0M/ 00M/ 000M TX up-link port with PoE PD function. It
accepts power from PoE power souring equipment (PSE) and delivers power to PoE powered
device (PD), which are compliant with IEEE802.3af and IEEE802.3at standard to receive and
deliver both Ethernet data and DC power through the traditional UTP or STP cable. The PoE
Switch can extend Ethernet data and DC power up to 200 meters. This manual will help you to
install and maintain the PoE switch. Installation of the PoE switch is very easy and you can start to
use the product as soon as it has powered up.
2. Hardware Description
*L D Indicator
There are 2 LEDs on the PoE switch to indicate the status of power and signal. The following
section describes the functions of each LED indicator.
Front panel detail

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
4
*POWER LED
LED
STATUS Description
Power
Green
LED ON when power input (DC IN on
rear panel or UPLINK on front panel
) has
valid power supplied.
Red
The indicator is used on full range
voltage model(PSE-SW5G- x ) and
2VDC typical model(PSE-SW5G52x0),
LED ON when the following warning
condition happens.
*Power input under voltage (Vin< 0V)
*Power input over voltage (Vin>59V)
*PoE over current (2A/per port)
the indicator is unused on 24V typical
model(PSE-SW5G-25x4),48V typical
model(PSE-SW5G44x4) and 4
individual input
(P/N:PSE-SW5G XN).
.
Off No power supplied.
*SWITCH LED (the right indicator on RJ45)
LED STATUS Description
P ~P5
Link/Act
Green A network device is detected ( 000Mbps),
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 000Mbps.
Yellow A network device is detected ( 0Mbps or
00Mbps), but no communication activity
is detected.

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
5
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 0Mbps or
00Mbps.
Off No device is detected.
*PoE LED (the left indicator on RJ45)
P ~P4
PoE
Yellow A valid Powered Device (PD) is detected
and delivering power on this port.
Off No PD is detected on this port.
UPLINK (P5)
PoE
Yellow
Power via another PoE
24V typical model(PSE-SW5G25x4) &
48V typical model(PSE-SW5G44x4):
Powered via all 4 data pairs.
Full range voltage model
(PSE-SW5G x ), &4 individual input
(P/N:PSE-SW5G XN): (2 data pairs or 4
data pairs)
Yellow
Blanking
24V typical model(PSE-SW5G25x4) &
48V typical model(PSE-SW5G44x4):
Powered via 2 data pairs. ( ,2,3,6 or 4,5,7,8
are all acceptable).
Full range voltage model
(PSE-SW5G x ), & 4 individual input
(P/N:PSE-SW5G XN):unused.
Off No power is detected on this port.

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
6
*Power wiring
The PoE switch family includes 5 models, be used for 5 different ranges of input voltage:
full range voltage ( 2 to 57VDC) (P/N: PSE-SW5G ,PSE-SW5G 4 ,PSE-SW5G 8 )
2VDC typical ( 0 to 5VDC) (P/N: PSE-SW5G52 0,PSE-SW5G5240,PSE-SW5G5280)
24VDC typical ( 2 to 36VDC) (P/N: PSE-SW5G25A4,PSE-SW5G25B4,PSE-SW5G25D4)
48VDC typical (44 to 57VDC) (P/N: PSE-SW5G44A4,PSE-SW5G44B4,PSE-SW5G44D4)
4 individual inputs ( 2 to 57VDC) (P/N:PSE-SW5G XN)
The PoE switch family allows for it to be powered by another PoE source on port 5 (UPLINK) as a
PoE repeater or extender. For PSE-SW5G25x4 and PSE-SW5G44x4 are 44~57VDC, for full range
voltage model(PSE-SW5G x ), and 4 individual input model(PSE-SW5G XN) are
2~57VDC. The 2VDC typical model(PSE-SW5G52x0) without PoE input function.
For PoE operation, make sure your power supply can offer at least 75W for 4x 802.3af PoE port, or
50W for 4x 802.3at PoE port.
If powered via the rear terminal, please make sure the input current is not over 0A. total output 8A
maximum.
If powered on port 5, the input current is not over 2Amp. Total output 2A maximum.
Ports ~4 will deliver DC power over the Ethernet cable as detailed below:
Mode A:
* Data pair A plus V+ on line and 2
* Data pair B plus V- on line 3 and 6
* Data pair C on line 4 and 5
* Data pair D on line 7 and 8
Mode B:
* Data pair A on line and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
7
Mode D (dual,=A+B):
* Data pair A plus V+ on line and 2
* Data pair B plus V- on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
Port 5 may receive DC power over the Ethernet cable, as detailed below:
* Data pair A plus V+ /V- on line and 2
* Data pair B plus V-/V+ on line 3 and 6
* Data pair C plus V+/V- on line 4 and 5
* Data pair D plus V-/V+ on line 7 and 8
The terminal block on the rear panel should be wired as detailed below:
The DIN-4P connector on the rear panel also used for power input, you can use an AC/DC adapter
with DIN-4P connector directly, recommends adaptor products as detailed below: (OPTION)
MS- 80- 8 MS- 80-24 MS- 80-48 MS- 80-56
Maximum output
8VDC/8.35A 24VDC/6.25A 48VDC/3.75A 56VDC/3.2A
Related model
PSE-SW5G
PSE-SW5G 4
PSE-SW5G 8
PSE-SW5G25A4
PSE-SW5G25B4
PSE-SW5G25D4
PSE-SW5G XN
PSE-SW5G
PSE-SW5G 4
PSE-SW5G 8
PSE-SW5G25A4
PSE-SW5G25B4
PSE-SW5G25D4
PSE-SW5G XN
PSE-SW5G
PSE-SW5G 4
PSE-SW5G 8
PSE-SW5G44A4
PSE-SW5G44B4
PSE-SW5G44D4
PSE-SW5G XN
PSE-SW5G
PSE-SW5G 4
PSE-SW5G 8
PSE-SW5G44A4
PSE-SW5G44B4
PSE-SW5G44D4
PSE-SW5G XN

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
8
*For 24VDC typical model(PSE-SW5G25x4)
Please note that the maximum power per port of 35W can only be achieved using 24VDC input
operation. If your input is 2VDC, then the total power per port should be de-rated to 7W per port.
Total output of 24VDC typical model is 35W(802.3at) x2 or 7W (802.3af) x 4.
*For 48VDC typical model(PSE-SW5G44x4) (PSE-SW5Gxxx4)
The input voltage must be in the range of 44 to 57VDC if running for 802.3af operation.
The input voltage must be in the range of 50 to 57VDC if running for 802.3at operation.
If the 48VDC typical model is not powered with the above designated input voltage, it will only
function as an Ethernet switch without PoE output.
Model Input Voltage
(REAR)
Input Voltage
(Port 5) Output voltage 802.3af/at
I olated
PSE-SW5G
PSE-SW5G 4
PSE-SW5G 8
2-57VDC No input
2-57VDC
(As input voltage)
(non-regulated)
No No
No input 2-57VDC 2-57VDC
(non-regulated) No No
2-57VDC 2-57VDC
Higher voltage
output
(REAR or Port 5)
No No
PSE-SW5G25A4
PSE-SW5G25B4
PSE-SW5G25D4
2-36VDC No input
56VDC
(regulated) Yes No
No input 44-57VDC 44-57VDC
(non-regulated) Yes No
2-36VDC 44-57VDC 56VDC
(regulated) Yes No
PSE-SW5G44A4
PSE-SW5G44B4
PSE-SW5G44D4
44-57VDC No input 44-57VDC
(non-regulated) Yes No
No input 44-57VDC 44-57VDC
(non-regulated) Yes No
44-57VDC 44-57VDC
Higher voltage
output
(REAR or Port5)
Yes No

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
9
PSE-SW5G52 0
PSE-SW5G5240
PSE-SW5G5280
0- 5VDC No input 24VDC
(regulated) No No
PSE-SW5G XN
2-57VDC No input
2-57VDC
(As input voltage)
(non-regulated)
No No
No input 2-57VDC 2-57VDC
(non-regulated) No No
2-57VDC 2-57VDC
Higher voltage
output
(REAR or Port 5)
No No
* thernet Port Wiring
The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port
~4 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for
0Base-T, 00Base-TX or 000Base-T connection. Automatic MDI/MDI-X crossover allows you
to connect to other devices (switches, hubs, or workstations etc.), without regard to using
straight-through or crossover cabling.
Port to 4 provides Power over Ethernet function that delivers DC power through the data pairs C
& D (pin 4,5 and pin 7,8) (mode B) to the PD. Port 5 provides Power Device function that receive
power from 4 pairs or 2 pairs Ethernet cable.
The following tables describe the wiring diagram of straight-through and crossover cabling. The
crossover cables simply cross-connect the transmit lines at each end to the receive lines at the
opposite end.

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
10
Straight-through Cabling
Pin Pin
Pin 2 Pin 2
Pin 3 Pin 3
Pin 6 Pin 6
Pin 4 Pin 4
Pin 5 Pin 5
Pin 7 Pin 7
Pin 8 Pin 8
Cross-over Cabling
Pin Pin 3
Pin 2 Pin 6
Pin 3 Pin
Pin 6 Pin 2
Pin 4 Pin 7
Pin 5 Pin 8
Pin 7 Pin 4
Pin 8 Pin 5
Connect an Ethernet cable into any switch port and connect the other side to your
attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network
device connected.
The maximum cable length for 0/ 00/ 000BaseT with Cat 5 twisted pair cables is typically 00m
(328 ft.).

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
11
*PD Port Wiring
Port to 4 provides PoE injection function with maximum 35W ability to power up the powered
device using the straight-through or cross-over Ethernet cable.
The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following
table shows pin assignment of alternative A and B for the Power Source Equipment.
Conductor Alternative A
(MDI-X)
Alternative A
(MDI)
Alternative B
(All)
Negative Vport Positive Vport
2 Negative Vport Positive Vport
3 Positive Vport Negative port
4 Positive Vport
5 Positive Vport
6 Positive Vport NegativeVport
7 Negative Vport
8 Negative Vport
Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8.
If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and
won’t deliver DC power to the PD. The yellow PoE LED will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port
LED is off, go back and check for connectivity problems between that port and the network device
connected.
*Network Application
The PoE Switch can receive power from a PoE midspan and provide power to the PD which
follows the IEEE 802.3af/at standard in the network. The PoE Switch can be installed in a more
appropriate position for better performance to extend Ethernet to 200 meters. The following figure
is an example of a network application for the PoE Switch.

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
12

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
13
3. Model Information
Model number Input Voltage Vout/pin out/Iout Output Wattage
Remark
PSE-SW5G1111 12 57VDC(P3)
12 57VDC(POE)
Vi/1236/2A 2A/port
PSE-SW5G1141 12 57VDC(P3)
12 57VDC(POE)
Vi/4578/2A 2A/port
PSE-SW5G1181 12 57VDC(P3)
12 57VDC(POE)
Vi/1236+4578/2A 2A/port
PSE-SW5G25A4 12-36VDC(P3)
44 57VDC(POE)
56VDC/1236/0.625A 35W/port 802.3at
PSE-SW5G25B4 12-36VDC(P3)
44 57VDC(POE)
56VDC/4578/0.625A 35W/port 802.3at
PSE-SW5G25D4 12-36VDC(P3)
44 57VDC(POE)
56VDC/1236+4578/0.625A
35W/port 802.3at
PSE-SW5G44A4 44-57VDC(P3)
44 57VDC(POE)
Vi/1236/0.625A 35W/port 802.3at
PSE-SW5G44B4 44-57VDC(P3)
44 57VDC(POE)
Vi/4578/0.625A 35W/port 802.3at
PSE-SW5G44D4 44-57VDC(P3)
44 57VDC(POE)
Vi/1236+4578/0.625A 35W/port 802.3at
PSE-SW5G5210 10 15VDC 24V/1236/0.84A 20W/port
PSE-SW5G5240 10 15VDC 24V/4578/0.84A 20W/port
PSE-SW5G5280 10 15VDC 24V/1236+4578/0.84A 20W/port
PSE-SW5G11XN 12 57VDC Vi/4578/2A 2A/port 4 individual
input

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
14
4. Technical Specifications
Standards IEEE802.3/IEEE802.3u standards/IEEE802.3ab ( 0
base-T/ 00base-TX/ 000base-T)
Ports 5 ports with PoE (4 PSE & PD), support auto-crossover &
auto-polarity
Transmission speed 000Mbps ( 000base-T). 00 Mbps ( 00base-TX), 0 Mbps( 0base-T)
Auto-negotiation
Switch technology store-and-forward
Protocols CSMA/CD
Flow control IEEE802.3x (full-duplex), back pressure (half-duplex)
Data transmission rate 488000pps for 000base-T, 48800pps for 00base-T, 4880pps for
0base-T
Address table 2K MAC address table, self-learning
Connect RJ-45
PoE port Port -4, PSE auto power management
Pin assignment:
*A mode:
data pair A plusV+( ,2),
data pair B plusV-(3,6),
data pair C (4,5),
data pair D (7,8)
*B mode:
data pair A ( ,2),
data pair B (3,6),
data pair C plusV+(4,5),
data pair D plus V-(7,8)

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
15
*A+B mode:
data pair A plusV+( ,2),
data pair B plusV-(3,6),
data pair C plusV+(4,5),
data pair D plus V-(7,8)
Port 5, 4 pairs PD
Maximum PoE power Port -4: IEEE802.3af – 6.8W
IEEE802.3at – 35W
Current limited – 2A
24V output – 20W
(Total power for PSE-SW5G25x4 – 70W)
Port 5: 90W (802.3at 2 event classification)
Current limited – 2A
PSE disconnect mode DC disconnect
PoE auto detection IEEE802.3af & IEEE802.3at (2 event classification signaling)
PoE protection Over-temperature, over-current, over/under voltage
LEDs *Link/Activity (Green ON/ Green Blinking @ 000Mbps,
Yellow/Yellow Blinking @ 0M/ 00Mbps)
*PoE (Yellow) port -4 ON - PD detect
Port 5 PSE-SW5G25x4 & PSE-SW5G44x4
ON – 4 pair power, Blinking-2 pair power
PSE-SW5G x ,PSE-SW5G52x0 &
PSE-SW5G XN ON – 2 or 4 pair power
*POWER Green-normal, Red-alarm
Power input Port 5 (UPLINK) from network switch or midspan, or optional DC
power supply.
(see detail on page 8)

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
16
Power consumption less than 5W when without PD loading
Input PSE-SW5G x
PSE-SW5G25x4
PSE-SW5G44x4
2V 0. 90A 0.340A 0. 90A
24V 0. 04A 0. 70A 0. 04A
48V 0.06 A --- 0.06 A
56V 0.056A --- 0.056A
Power efficiency 85% at full load (@48V typical)
Operating temperature -20℃~ +75℃
Operation humidity 90% relative humidity, non-condensing
Storage temperature -40℃~+85℃
Dimension 40mm(H)x 8mm(W)x 50mm(D) DIN RAIL Mountable
Surge Protection on data pair
Signal
Operating Voltage Data 5V
Clamping Voltage
Data 6.5V (@I PP =5A, t p =8/20μs, I/O pin to GND)
Peak Pulse Current 20A (tp=8/20μs)
Pin Protected All 8 pin protected
Max. Shut Capacitance <3pF (VR = 0V, f = MHz, I/O pin to GND)
< .5 pF (VR = 0V, f = MHz, Between I/O pins)
IEC COMPATIBILITY (EN6 000-4)
IEC6 000-4-2 (ESD) ± 5kV (air), ±8kV (contact)
IEC6 000-4-4 (EFT) 40A (5/50ns)
IEC6 000-4-5 (Lightning) 20A (8/20μs)
NOTICE:
The product is not comply to LPS requirement, it need to evaluate at final system

User’s Manual PSE-SW5G series
MSTRONIC CO., LTD.
17