MSTRONIC MSE PSE-SW5G User manual

USER’S MANUAL
MSTRONIC CO., LTD.
MSE PSE-SW5G
5 Port PoE Switch & Extender
(Repeat Ethernet and PoE)

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators.......................................................................................
Power Wiring ........................................................................................
Ethernet Port Wiring..............................................................................
PD Port Wiring......................................................................................
Network Application……………………………………............................
3. Model Information...........................................................
4. Technical Specification........................................................
3
3
3
5
8
10
11
12
13

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
3
1. General Information
The PoE (Power Over Ethernet) Switch family provide four 10M/100M/1000M TX ports with PoE
PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It allows power
souring equipment (PSE) to be powered from PoE and deliver power to PoE powered device (PD),
which are compliant with IEEE802.3af and IEEE802.3at standard to receive and deliver both
Ethernet data and DC power through the traditional UTP or STP cable. The PoE Switch can extend
Ethernet data and DC power up to 200 meters. This manual will help you install and maintain the
PoE switch. Installation of the PoE switch is very easy and you can start to use the product as soon
as you are powered up.
2. Hardware Description
*LED Indicator
There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following
section describes the functions of each LED indicator.
Front panel detail

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
4
*POWER LED
LED
STATUS Description
Power
Green
LED ON when power input (DC IN on
rear panel or Port 5 (UPLINK) on front
panel) has valid power supplied.
Red
The indicator is only used on
PSE-SW5G11CN, LED ON when the
following warning condition happens.
*Power input under voltage (Vin<10V)
*Power input over voltage (Vin>59V)
*PoE over current (2A/per port)
the indicator is unused on
PSE-SW5G24DN/PSE-SW5G44DN
Off No power supplied.
*SWITCH LED (the right indicator on RJ45)
LED STATUS Description
P1~P5
Link/Act
Green A network device is detected (1000Mbps),
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 1000Mbps.
Yellow A network device is detected (10Mbps or
100Mbps), but no communication activity
is detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off No device is detected.

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
5
*PoE LED (the left indicator on RJ45)
P1~P4
PoE
Yellow A valid Powered Device (PD) is detected
and delivering power on this port.
Off No PD is detected on this port.
UPLINK (P5)
PoE
Yellow
Powered via all 4 data pairs.
Yellow
Blanking
Powered via 2 data pairs. (1,2,3,6 or 4,5,7,8
are all acceptable).
Off No power is detected on this port.
the indicator is unused on PSE-SW5G11CN
*Power wiring
The PoE switch family includes 3 models, be used for 3 different ranges of input voltage:
full range voltage (12 to 57VDC) (P/N: PSE-SW5G11CN)
24VDC typical (12 to 36VDC) (P/N: PSE-SW5G24DN)
48VDC typical (40 to 57VDC) (P/N: PSE-SW5G44DN)
The PSE-SW5G24DN and PSE-SW5G44DN allow power by another PoE source (42.5~57VDC)
on port 5 (UPLINK) as a PoE repeater or extender.
For PoE operation, make sure your power supply may offer at least 75W for 4x 802.3af PoE port, or
150W for 4x 802.3at PoE port.
If powered via the rear terminal, please make sure the input current is not over 10A. If powered on
port 5, make sure the input current is not over 2Amp.
Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
6
Port 5 may get DC power over the Ethernet cable, as detailed below:
* Data pair A plus V+ /V- on line 1 and 2
* Data pair B plus V-/V+ on line 3 and 6
* Data pair C plus V+/V- on line 4 and 5
* Data pair D plus V-/V+ on line 7 and 8
The terminal block on the rear panel should be wired as detailed below:
*For PSE-SW5G24DN
Please note that the maximum power per port of 35W can only be achieved using 24VDC input
operation. If your input is 12VDC, then the total power per port should be de-rated to 17W per port.
Total output of PSE-SW5G24DN is 35W(802.3at) x2 or 17W (802.3af) x 4.
*For PSE-SW5G44DN
The input voltage must be in the range of 44 to 57VDC if running for 802.3af operation.
The input voltage must be in the range of 50 to 57VDC if running for 802.3at operation.
If the PSE-SW5G44DN is not powered with the above designated input voltage, it will only
function as an Ethernet switch without PoE output.

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
7
Model Input Voltage
(REAR) Input Voltage (Port 5) Output voltage 802.3af/at
Isolated
PSE-SW5G11CN
12-57VDC No input
12-57VDC
(As input voltage)
(non-regulated) No No
PSE-SW5G24DN
12-36VDC No input 56VDC
(regulated) Yes No
No input 42.5-57VDC
42.5-57VDC
(As input voltage)
(non-regulated)
Yes No
12-36VDC 42.5-57VDC 56VDC
(regulated) Yes No
PSE-SW5G44DN
40-57VDC No input
40-57VDC
(As input voltage)
(non-regulated) Yes No
No input 42.5-57VDC
42.5-57VDC
(As input voltage)
(non-regulated)
Yes No
40-57VDC 42.5-57VDC
Higher voltage
output
(REAR or Port5)
Yes No
You can use the PSE-SW5G series with our adaptor products as detailed below: (OPTION)
MS-A150-18 MS-A150-24 MS-A150-48
Maximum output 18VDC/7.5A 24VDC/6.25A 48VDC/3.125A
Related model PSE-SW5G11CN
PSE-SW5G24DN
PSE-SW5G11CN
PSE-SW5G24DN
PSE-SW5G11CN
PSE-SW5G44DN

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
8
*Ethernet Port Wiring
The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port
1~4 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for
10Base-T, 100Base-TX or 1000Base-T connection. Automatic MDI/MDI-X crossover allows you
to connect to other devices (switches, hubs, or workstations etc.), without regard to using
straight-through or crossover cabling.
Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs C
& D (pair 4,5 and pair7,8) to the PD. Port 5 provides Power Device function that receive power
from 4 pairs or 2 pairs Ethernet cable. (PSE-SW5G11CN without the PD function)
The following tables describe the wiring diagram of straight-through and crossover cabling. The
crossover cables simply cross-connect the transmit lines at each end to the receive lines at the
opposite end.
Straight-through Cabling
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Pin 6 Pin 6
Pin 4 Pin 4
Pin 5 Pin 5
Pin 7 Pin 7
Pin 8 Pin 8

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
9
Cross-over Cabling
Pin 1 Pin 3
Pin 2 Pin 6
Pin 3 Pin 1
Pin 6 Pin 2
Pin 4 Pin 7
Pin 5 Pin 8
Pin 7 Pin 4
Pin 8 Pin 8
Connect an Ethernet cable into any switch port and connect the other side to your
attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network
device connected.
The maximum cable length for 10/100/1000BaseT with Cat 5 twisted pair cables is typically 100m
(328 ft.).

User’s Manual MSE PSE-SW5G series
MSTRONIC CO., LTD.
10
*PD Port Wiring
Port 1 to 4 provides PoE injection function with maximum 35W ability to power up the powered
device using the straight-through or cross-over Ethernet cable.
The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following
table shows pin assignment of alternative A and B for the Power Source Equipment.
Conductor Alternative A
(MDI-X) Alternative A (MDI) Alternative B (All)
1Negative Vport Positive Vport
2 Negative Vport Positive Vport
3 Positive Vport Negative port
4 Positive Vport
5 Positive Vport
6 Positive Vport NegativeVport
7 Negative Vport
8 Negative Vport
Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8.
If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and
won’t deliver DC power to the PD. The yellow PoE LED will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port
LED is off, go back and check for connectivity problems between that port and the network device
connected.