MSTRONIC PSE-SW5B15DBHM-IP66 User manual

USER’S MANUAL
MSTRONIC CO., LTD.
PSE-SW5B15DBHM-IP66
IP66 Waterproof
5 Port PoE Switch & Extender
(Repeat Ethernet and PoE)

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
2
1. General Information
The fanless PSE-SW5G PoE (Power Over Ethernet) Extender provides four 10M/100M/1000M TX
ports with PoE PSE function plus one 10M/100M/1000M TX up-link port with PoE PD function. It
accepts power from PoE power sourcing equipment (PSE) and delivers power to PoE powered
device (PD), which are compliant with IEEE802.3af and IEEE802.3at standard to receive and
deliver both Ethernet data and DC power through the traditional UTP or STP cable. The PoE
Switch can extend Ethernet data and DC power up to 200 meters when used as a PoE repeater.
2. Hardware Description
*LED Indicator
There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following
section describes the functions of each LED indicator.
Front panel detail
*POWER LED
LED
STATUS
Description
Power
Green
LED ON when power input (DC IN on rear
panel or UPLINK on front panel) has valid
power supplied.
Off
No power supplied.

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
3
*SWITCH LED (the right indicator on RJ45)
LED
STATUS
Description
P1~P5
Link/Act
Green
A network device is detected (1000Mbps), but
no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 1000Mbps.
Yellow
A network device is detected (10Mbps or
100Mbps), but no communication activity is
detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off
No device is detected.
*PoE LED (the left indicator on RJ45)
P1~P4
PoE Out
Yellow
A valid Powered Device (PD) is detected and
delivering power on this port.
Off
No PD is detected on this port.
p
UPLINK (P5)
PoE In
Yellow
Powered from another PoE,
Powered via all 4 pairs.
Yellow
Blinking
Powered via 2 pairs, data pairs (pin 1,2,3,6) or
spare pairs (pin 4,5,7,8) are all acceptable.
Off
No power is detected on this port.

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
4
*Power wiring
The PoE switch allows to be powered by another PoE source on port 5 (UPLINK) and/or on rear
terminal (green connector).
If powered on port 5 (UPLINK) as a PoE repeater, the PoE input must be 44~57VDC, the input
current should not be over 2Amp.
Port 5 PoE input current:Active: 44V[email protected] max(71W min)；Passive: 44V-57[email protected] max
If powered on port 5 (UPLINK), the output could be (af)16.8W x4port, or (at)35W x2port, or (bt)
60W(Type3 class6) x1port.
Model
Input Voltage
(REAR)
Input Voltage
(Port 5)
Output voltage
PSE-SW5B15DBHM
11-60VDC
(14.2A-2.78A)
No input
56VDC/2.55A
(regulated)
No input
44-57VDC
(2.0A max.)*
44-57VDC/2.0A
(non-regulated)
11-60VDC
(14.2A-2.78A)
44-57VDC
(2.0A max.)*
56VDC/2.55A
(regulated)
If powered on the rear terminal, PoE output (Port 1~4) are total 150W (Max.), Can be used for
35W (802.3at) x 4 or 75W(802.3bt)x2.
Please note the rear terminal (green connector) is capable of 12A max.
Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:
* Data pair A plus V- on line 1 and 2
* Data pair B plus V+ on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
Port 5 (UPLINK) may receive DC power over the Ethernet cable, as detailed below:
* Data pair A plus V+ /V- on line 1 and 2
* Data pair B plus V-/V+ on line 3 and 6
* Data pair C plus V+/V- on line 4 and 5
* Data pair D plus V-/V+ on line 7 and 8

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
5
The terminal block on the rear panel should be wired as detailed below, if the input voltage is in
11~16VDC, cause of heavy input current, please make sure the 4 input pins are all used.
*Ethernet Port Wiring
The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port
1~4 with PoE PSE) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for
10Base-T, 100Base-TX or 1000Base-T connection. Automatic MDI/MDI-X crossover allows you
to connect to other devices (switches, hubs, or workstations etc.), without regard to using
straight-through or crossover cabling.
Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs A
& B (pin 1,2 and pin 3,6) & data pairs C & D (pin 4,5 and pin 7,8) to the PD. Port 5 provides PD
function that receives power from 4 pairs or 2 pairs PoE.
The following tables describe the wiring diagram of straight-through and crossover cabling. The
crossover cables simply cross-connect the transmit lines at each end to the receive lines at the
opposite end.

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
6
Straight-through Cabling
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
Pin 6
Pin 6
Pin 4
Pin 4
Pin 5
Pin 5
Pin 7
Pin 7
Pin 8
Pin 8
Cross-over Cabling
Pin 1
Pin 3
Pin 2
Pin 6
Pin 3
Pin 1
Pin 6
Pin 2
Pin 4
Pin 7
Pin 5
Pin 8
Pin 7
Pin 4
Pin 8
Pin 5
Connect an Ethernet cable into any switch port and connect the other side to your
attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network
device connected.
The maximum cable length for 10/100/1000BaseT with Cat 5 twisted pair cables is typically 100m
(328 ft.).

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
7
*PD Port Wiring
Port 1 to 4 provides PoE injection function with maximum 35W(802.3at) or 90W(802.3bt) ability to
power up the powered device using the straight-through or cross-over Ethernet cable.
The PoE switch follows the IEEE802.3af/at Alternative B mode connector assignment. The
following table shows pin assignment of alternative A and/or B for the Power Source Equipment.
Conductor
Alternative A
(MDI-X)
Alternative A
(MDI)
Alternative B
(All)
1
Negative Vport
Positive Vport
2
Negative Vport
Positive Vport
3
Positive Vport
Negative port
4
Positive Vport
5
Positive Vport
6
Positive Vport
NegativeVport
7
Negative Vport
8
Negative Vport
Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8.
If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and
won’t deliver DC power to the PD. The yellow PoE LED will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port
LED is off, go back and check for connectivity problems between that port and the network device
connected.

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
8
*Network Application
The PoE Switch can receive power from a PoE midspan and provide power to the PD which
follows the IEEE 802.3af/at/bt standard in the network. The PoE Switch can be installed as a
PoE+Ethernet repeater to extend Ethernet to 200 meters. The following figure is an example of a
network application for the PoE Extender.

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
9
3. Technical Specifications
Standards IEEE802.3/IEEE802.3u standards/IEEE802.3ab (10base-T/100base-TX/
1000base-T)
Ports 5 ports with PoE (4 PSE & 1 PD), support auto-crossover & auto-polarity
Transmission speed 1000Mbps (1000base-T).100 Mbps (100base-TX), 10 Mbps(10base-T)
Auto-negotiation
Switch technology store-and-forward
Protocols CSMA/CD
Flow control IEEE802.3x (full-duplex), back pressure (half-duplex)
Data transmission rate 1488000pps for1000base-T, 148800pps for100base-T,
14880pps for 10base-T
Address table 2K MAC address table, self-learning
Connect RJ-45
PoE port Port 1-4, PSE auto power management
Pin assignment:
data pair A plus V-(1,2),
data pair B plus V+(3,6),
data pair C plus V+(4,5),
data pair D plus V-(7,8)
Port 5, 4 pairs PD
PoE power Output Max. from Port 5: af–16.8W x4 / at–35W x2 / bt–60W(Type3) x1 (total:71W)
from rear terminal : at–35W x4 or bt–75W x2 (total:150W)
PoE power Input(Port 5) Active: 71W min. for system, Current limited –1.62A@44-57V
(compliant to 802.3af/at/bt classification at 90W PSE input.)
Passive: Current limited –2.0Amax.@44-57V

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
10
PSE disconnect mode DC disconnect
PoE auto detection IEEE802.3af , IEEE802.3at (2 event classification signaling) &
IEEE802.3bt(multi-event classification)
PoE protection Over-temperature, over-current, over/under voltage & *Surge Protection
on data pairs*
LEDs Link/Activity (Green ON/ Green Blinking @1000Mbps,
Yellow/Yellow Blinking @10M/100Mbps)
*PoE (Yellow) Port 1-4 ON - PD detect
Port 5 ON –4 pair power, Blinking-2 pair power
*POWER Green-normal, Red-alarm
Power input PoE source on Port 5 (UPLINK), and/or optional DC power supply on
rear terminal. It’s with input low voltage protection, if input voltage
lower than 9.4V, the unit will be shut down.
Power consumption less than 5W when without PD loading
Input
PSE-SW5B15DBHM
12V
291mA/3.492W
24V
140mA/3.36W
48V
67.2mA/3.226W
Power efficiency 85% at full load (@24V typical)
Operating temperature -20℃~ +70℃
Operation humidity 90% relative humidity, non-condensing with conformal coating
Storage temperature -40℃~+85℃
Dimension 207mm(H)x268mm(W)x88mm(D)
With 6” hose clamp for light pole mounting

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
11
*Surge Protection on data pairs

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
12
IP class:IP66, anti-UV

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
13

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
14

User’s Manual PSE-SW5B15DBHM
MSTRONIC CO., LTD.
15