MUBVIEW ZS-GX7S User manual

A Smarter Safety Solution
QUICK START GUIDE
ZS-GX7S
www.mubview.com
[e-mail]
[phone]

Thanks for your shopping and trust.
We have been optimizing our products and improve
our lifetime customer service to oer you a better
shopping experience.
Instructions: This product does not support
5GHz WiFi networks and must be connected to
a 2.4GHz WiFi network!
If you have any problems, please feel free to write
us e-mail We will solve your problems within 24
hours.
In addition, your advice or suggestions will be
much appreciated and welcomed.
*If you're unsure how to find a 2.4GHz WiFi network, please
search Google for instructions or contact us.
Produkt-Service
Email:[e-mail]
Verteiler: [e-mail]
Mehr über uns
Web: www.mubview.com
Facebook:www.facebook.com/mubview
Warranty Service

1. Lens
2. Microphone
3. PIR
4. Speaker Holes
5. Bracket
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
11
12
6. Power Key
7. Charging Indicator
8. Ventilation Holes
9. Charging Port
10. Reset
11. Working Status
Indicator
12. SD Card Slot
Camera Introduction

The camera supports Android and iOS system.
Please scan the QR code below or search 'MUBVIEW' in App
store to download the App, and follow the instruction to
register account. If you encounter any problems during the
installation process, please feel free to contact us via
[e-mail]
Sign up in App with your email address.
Choose your region and correct country code
(Users from dierent regions cannot share the camera).
Download & Install App
Registrierung eines Kontos

1. Allow 'MUBVIEW' App to access mobile cellular
data and wireless LAN, or it will fail to add
camera.
2. Allow 'MUBVIEW' App to receive pop-up
messages, otherwise the smart phone will not
receive notification when motion is detected.
Add Camera to App

Preparation for Connection
1. Insert Micro SD card when the camera is Power o
(Supports up to 128GB.SD card not included). The
camera only works with 2.4GHz Wi-Fi, not support
5GHz Wi-Fi.
2. Take the camera close to the router while
connecting.
3. Keep pressing the power button for 2-4s to power
on/o the camera.
4. After turning on the camera for the first time, please
press and hold the Reset button for 2 to 4 seconds,
and then follow the instructions in the app to
connect the camera.

Connect the Camera to App
Add Device Select Your Device
Click “Next”
Click “Next”

Note: If the camera fails to connect to the network, please move the
camera closer to the Wi-Fi router, then press and hold the "Reset" button
for more than 5 seconds. Once you hear the prompt sound, reconnect the
camera. If the issue persists, please email us at [email protected]
Input 2.4G
Wi-Fi Password Prepare to Scan
Connecting Click “Next”
Wählen Sie ein 2,4G-
und 5G-WLAN-Netzwerk
aus und geben Sie Ihr
Passwort ein
Häufige Router-Setup-Methoden

Install The Camera
Mounting Height:
2-3 Meters
PIR Detecting Distance:1-7Meters
GX7S is only for indoor use,please install it indoors
according to the instructions and keep away from water
sources.
It's recommended to select the location before installation
Once the 3M glue is attached,it will not be easy to remove
(to avoid damage to the wall).
Install the camera 2-3 meters above ground.The detection
range of the motion sensor would be maximized at such a
height.
For eective motion detection,please install the camera
angularly.
NOTE:If a moving object approaches the PIR sensor vertically, the
camera may fail to detect motion.

Battery Management
1. The camera's Battery can last 1-2 months, assuming
triggering of 30 times/day.
2. Charger Standard:DC 5V 2A (adapter not included)
3. It takes 6-8 hours to fully charge it. Please fully
charge the camera before first use.
4. The battery durability depends on how frequently the
camera is woken up.The more times the camera is
woken up,the faster the battery drains.It is
recommended to lower down the 'Motion Detection'
sensitivity or turn it o occasionally.
To reduce false alerts,please note that:
Do not install the camera in a position facing strong lights/
glass/window/swimming pool.
Do not place the camera too close to any angle with busy
trac.
Recommended distance between the camera and motion
objects is within 7M(23ft)
Stay away from the outlets,including air conditioner vents,
humidifier outlets,the heat transfer vents of the projectors,
etc.
If there is any motion detection delay or false alerts, please
contact 24/7 after-sales service via [email protected]

5. The battery of your camera may drain faster below
32F(OC)
You can share your camera with
friends and family and choose
whether to allow them to monitor
or control your device.
Please note that you will only be
able to share if you confirm that
the user's location matches yours.
Device administrators can share
their devices with multiple people.
(Invitees need to download and
install the "MUBVIEW" application,
register an account, and log in to
the application.)
Step 1: The sharer scans the invitee's QR code or enters the
invitee's account.
Step 2: The invitee accepts the invitation.
Sharing steps:
When you receive low-battery alert on your app,it is suggested
to take the camera down and fully recharge it indoor,or you can
connect it to the power cable all the time.
Multi-User Sharing

FAQ
For more detailed FAQs, please log in to the APP, search in "Me"-"FAQ"-
"Help Document" ; Or contact us by e-mail
1) Check whether the equipment is in the power-on state, and observe
whether the working light of the equipment is on normally.
2) Check whether the Wi-Fi network is in good condition and restart
the router.
3) If the device is located far away from the router, which results in the
inability to obtain a good Wi-Fi signal, it is recommended to move
the router to a closer place or add a Wi-Fi amplifier to improve the
Wi-Fi performance of the home.
4) Delete the camera from your Mubview account and add it again
after esetting the device.
Check whether the device firmware and application program are the
latest version.
The device prompts oine?
Delete the camera from your Mubview account. After resetting the
device, use the new Wi-Fi and password to add it again.
Update router or Wi-Fi password?
1) Check the status of the SD card in "Settings" to ensure that the SD
card has been successfully recognized.
2) Reinsert the SD card.
3) In the application, format the SD card.
4) Try another new SD card.
Can't play historical video?

Alarm push frequently?
1) In the App, lower the sensitivity of the motion detection alarm.
2) Check whether there are objects that interfere with and trigger the
PIR sensor in the field of view of the device, such as the outdoor
unit of the air conditioner, driving cars, passing pedestrians, etc.
The angle of the device can be adjusted appropriately to avoid
these easily disturbing objects.
3) Turn on "human motion detection" and use humanoid algorithm
to filter useless.
1) Turn on all the push permissions of the "Mubview" application in
the system settings of your mobile phone.
2) Make sure that the device's motion detection function is successfully
turned on.
3) Restart the phone, and clear the cache on Android phones.
4) Check whether the network is good.
The phone cannot receive the alarm push?
1) If the indicator has a solid red light, please reset or unplug the
device, then setup again.
2) If reset does not work, please contact our technical engineer team
([e-mail]) , to get upgrading package to upgrade
your device ( please check if you have a. SD card reader and a SD
card first).
3) If all of the above methods does not work, please feel free to
contact us for further solution.
The indicator has a solid red light
How to Troubleshoot Network Connections

The above case might be caused by any of the following reasons:
the QR code is abnormal, the lens is defocused or the device is
defective.
1) Make sure your phone is 5-8 inches from the lens and try to scan
the QR code from dierent angles.
2) If your phone is a new brand, this might cause the abnormal QR
code. In this case, please provide us a screenshot of the QR code
and the model and operation system version of your phone.
3) Make sure the lens is clean. Try AP mode to setup your phone and
then check whether the lens is defocused.
4) If you still failed to setup your device and the device does not make
any response when setup. Please provide us the SN of your device,
the screenshot of QR code, the exact time you setup your device
(if possible, please provide a video of setting up your device) for a
further troubleshooting.
The indicator is red and blinking slowly but does not blink
fast after the device scanned the QR code, and does not
make a sound like "bee"
The indicator blinking fast red light means the device has recognized
the QR code successfully. Reasons for device failed to setup might be
as the following:
1) The wifi is 5G instead of 2.4G.
2) Wrong password.
The indicator is red and blinking slowly and turns fast red
light after the device scanned the QR code. But the fast red
light does not turn blue

3) Unstable network. Please put your device next to the router when
setup. If this still does not work, please reboot your router and reset
your device to try again. Also, you can try to use your mobile data
as hotspot to setup your device to test if it works with hotspot wifi.
4) If it does not work with hotspot, the Wifi antenna inside the device
might be defective. In this case, please feel free to contact us for
further solution.
Please provide us your SN/ account info as well as the exact time you
setup your device.We will forward these info to the technical engineer
team for a further troubleshooting.
MUBVIEW ocial after-sales email: [e-mail]
The indicator is red and blinking slowly and turns fast red
light after the device scanned the QR code. And the fast red
light turns blue after a while but the device failed to addto APP

FCC ID: 2AZL7-ZS-GX1S
Made In China