Multiform PS020A User manual

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 16
■APPENDIXES
A. Safety rules for overhead rigging (applicable if the PS020A DMX-controlled 3-
Channel power supply is mounted to any of the Multiform LS series passive RGB LED
panels):
Risk of injury: Overhead mounting requires extensive experience,
including among others calculating working load limits, good knowledge
of the installation material being used, and periodic safety inspection of
all installation material and the unit. If you lack such qualifications, do
not attempt the installation yourself. Improper installation can result in
body injury. Be sure to complete all rigging and installation procedures
before applying power to the unit.
•The unit should be installed out of reach of people and outside areas where
persons may walk by or be seated.
•Make sure that the installation area can hold a minimum point load of 10 times the
device’s weight.
•In fixed installations, fix the unit with self-locking screws/nuts to the mounting point.
•When mounting the unit to truss be sure to secure an appropriately rated clamp to
the hanging yoke using a M10 screw fitted through the center hole of the hanging
yoke.
•Always use a certified safety cable that can hold 12 times the weight of the device
when installing the unit. This secondary safety attachment should be installed in a
way that no part of the installation can drop more than 20cm if the main attachment
fails.
•Never stand directly below the device when mounting, removing, or servicing the
fixture. Make sure the area below the installation place is free from unwanted
persons during rigging, de-rigging and servicing.
•The operator has to make sure that the safety-relating and machine-technical
installations are approved by an expert before using them for the first time. The
installations should be inspected every year by a skilled person to be sure that
safety is still granted.
USER MANUAL
PS020A
DMX-controlled 3-Channel power supply
Updated versions of this document may be available at
WWW.MULTIFORM-LIGHTING.COM
RevA 06/2007 Order code: 12-010-0233-80100-1-01

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 2
■Introduction
Dear customer,
congratulations on the purchase of a Multiform-branded item and the trust having been
put in us with this decision. Multiform is one of the leading global manufacturers of
professional lighting equipment and has decades of experience in design, production
and quality assurance.
To meet your requirements, this unit has been designed and built to the highest
standards, so that we can assure you that you have made a good and satisfying
investment. To take full advantage of all possibilities and for your own safety and the
safety of your environment, please read these operating instructions carefully before
you start using the unit.
■Product description
The PS020A DMX-controlled 3-Channel power supply is a versatile unit that integrates
power supply and control functions for the Multiform LS series of passive RGB LED
panels, such as:
The Multispot ® LS1310 passive RGB LED panel
The Multiwash ® LS1130 passive RGB LED panel
The Multiflood ® LS3042 passive RGB LED panel
For extended user advice, please refer to the respective panel’s user manual.
■Security advice before use
Warning: Read this section carefully before installing, powering,
operating, cleaning or servicing this product!
The following symbols are used to identify important safety information in this manual:
DANGER!
Safety hazard. Risk
of injury or death.
WARNING!
Hazardous voltage.
Risk of severe or
fatal electric shock.
WARNING!
Fire hazard.
WARNING!
Read manual before
installation and
operation.
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 15
■Technical data PS020A DMX-controlled 3-Channel power supply:
Mains Input…………………………………………………………….85-240V AC / 50-60Hz
Type………………………………………………………………..switch mode power supply
Power Consumption…………………………………………………………………max. 48W
Fuse………………………………………………….250V 2A T (slow blow, 5x20mm glass)
Sound control………………...…internal microphone with Automatic Gain Control (AGC)
DMX connections…………………………………………………3 pin XLR (Male / Female)
Modulation Type…………………….…………….Advanced Bit Angle Modulation (ABAM)
Control protocol.......................................................................................DMX 512 (1990)
Dimensions………………………………………………………..W 135 x H 109 x D 38 mm
Weight …………………………………………………………………………………….0,6 kg
■Standards
This product complies with the following standards:
EU safety...........................................................................................EN 60065:2001 +A1
EU EMC..................................................................................................EN61204-3:2001
US safety (pending)…………..………………………………………………………UL60065
US EMC………………………..…………………………………………………..FCC Part 15
This product meets both the EMC Directive 89/336/EEC and the Low Voltage Directive
73/23/EEC.

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 14
Maintenance (Boot loader)
The Maintenance (boot loader) function enables the unit to receive firmware updates
via the DMX connectors. For further information refer to the website www.multiform-
lighting.com and check “Download”.
Switch on condition
The unit always returns to the last mode before it was switched off. In DMX Slave “SLA”
or DMX Mode “d” or DMX Preset Mode “P” all DMX values are cleared (LED’s off) if
power is switched off.
DMX signal drop condition
The device will retain the status that it was in before the DMX signal got lost, but
potential strobe settings will be automatically cleared.
DMX channel assignment overview:
Mode >
DMX
A C P
(CH3<50)
P
(CH3>50)
d SLA
CH1 Red Red Colour Pattern Red Red
CH2 Green Green Dimmer Dimmer Green Green
CH3 Blue Blue 0-49 Speed Blue Blue
CH4 0 0 Strobe Strobe Dimmer/Strobe 0
■Maintenance
This unit does not need regular maintenance. The internal circuit is protected by a
250V/2A slow-blow fuse 5x20mm fuse. If this fuse fails, this usually indicates an
internal fault requiring servicing by a qualified engineer. The fuse shall only be replaced
by a fuse of same specification, and the replacement has to be made by qualified
personnel obeying applicable safety rules.
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 3
General advice:
1. Read this manual completely before using the product.
2. Keep this manual in your records for future reference.
3. Follow all instruction printed in this manual, otherwise warranty
may be void.
4. Follow all printed security advice on the product itself. The lighting
flash with arrowhead within an equilateral triangle makes you
aware of non-insulated AC mains voltage inside the unit. The
exclamation mark within an equilateral triangle makes you aware of
important operating and maintenance instructions in the literature
attached to this product.
5. Take care of enough distance between this product and sources of
hum and noise like electric motors and transformers.
6. Carry this product with greatest care. Punches, big forces and
heavy vibration may damage this product mechanically.
7. The manufacturer takes no responsibility for injury or damage
caused by not following the safety precautions and instructions
printed in this manual.
Protection from electric shock:
1. Do not connect the AC power plug to the unit before assembly has
been completed.
2. Only connect this unit to a mains socket outlet with protective earth
connection, ground-fault (earth-fault) protection and overload
protection.
3. Where the mains plug or an appliance coupler is used as a dis-
connect device, the disconnect device shall remain readily
operable.
4. To pull the AC Cord out of the wall outlet or the unit’s AC socket,
never pull the cable itself, but only the AC plug.
5. Disconnect the unit from AC supply by pulling the AC plug out of
the wall outlet or the unit’s AC socket before any kind of cleaning
on the product. Use smooth and dry cloth only for cleaning. Check
all connection cables before reconnecting the unit.
6. Do not expose this unit to any dripping or splashing liquids, and do
not place objects filled with liquids, such as vases, on the unit. Do
not operate this unit near to open water or in high humidity.
7. Choose the position of the AC cord according to the lowest risk of
damage by foot steps or by squeezing it. Take especially care of
the AC cord outlet on the unit as well as the AC plug and wall outlet
at the other end of the cable.
8. Do not open the unit for service purpose, as there are no user-
serviceable parts inside. Warranty will be void in any case of
unauthorized service by the user or other not authorized persons.

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 4
Protection from fire:
1. Take care of not placing the unit near sources of heat (e.g.
powerful amplifiers, fog machines).
2. Take always care of sufficient air convection in the unit’s
environment to avoid overheating, especially when mounting in a
closed environment. Make sure air convection slots are not
blocked. Do not operate this unit in environmental temperatures
exceeding 40 degrees Celsius.
3. Check the total maximum power of your AC wall outlet if you
connect several units to one wall outlet and avoid any overloading.
Protection from injury and damage:
1. Never use any accessories or modifications not authorized by the
manufacturer of this unit.
2. Choose a location for operation where the unit is protected from
vibration and where a fixed mounting position is provided. In case
of overhead-mounting, follow appropriate rigging rules and your
country’s regulations for rigging safety. See appendixes if any.
3. Before plugging the AC cord in the wall outlet, check whether the
AC mains voltage and frequency is the same as this product is
specified for. Whenever your AC plug should not match the wall
outlet, contact you dealer immediately.
4. If fluids have spilled into the unit or small parts have intruded the
unit, immediately switch off the unit and hand it over to the
authorized service for a security check.
5. Disconnect the unit from AC supply by pulling the AC plug out of
the wall outlet or the unit’s AC socket during a thunder-storm in
order to avoid any damage on the unit due to AC voltage peaks.
6. In cause of not correct function of this unit or damaged AC cord or
other damaged parts, pull immediately the AC plug out of the wall
outlet and hand the unit over to the authorized service for a
security check.
7. To meet all aspects of functionality and security during mainte-
nance work to be preformed on this unit, all parts should be
replaced by genuine spare parts. Consequently, take care of your
dealer or maintenance company to be authorized by the
manufacturer.
■Health advice
This unit produces and absorbs electromagnetic radiation. The strength of radiation and
the sensitivity for disturbing interference matches the CE and FCC requirements. A
corresponding sign is printed on the backside of the unit. Any change or modification
may affect the behavior of the unit concerning electromagnetic radiation, with the CE
requirements eventually not to be met any more. The manufacturer takes no
responsibility in this case.
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 13
The pre-programmed soft fade or hard switching patterns can be chosen by means of
CH1 whilst CH2 is used as a dimmer channel. CH3 allows to set the fade time or
pattern speed from slow (value 50) to very fast (value 255). If channel 4 reaches a DMX
value of 50 or above a strobe will be added to the chases. The strobe speed can be
adjusted from slow (value 50) to 23 flashes per second (value 255).
Note: Whether the unit works in static colour mode or pattern mode only depends on
the value of channel 3. So make sure the value of channel 3 is lower than 50 to be in
static colour mode. Otherwise you will be in pattern mode.
In this mode the potentiometer (1) is disabled.
Addressing has to be done as follows:
001 first device (CH 1-4) *factory default*
005 second device (CH 5-8)
009 third device (CH 9-12)
013 fourth device (CH 13-16) and so on.
This setting is stored even if the device is switched off.
Display on/off
If you wish the display to be lit only when a change in operation is made, the DIP switch
(10) should be in the position off. Now if any of the buttons is not pressed for more than
approximately 25 seconds the display is switched off. As soon as one of the buttons is
pressed again, the display switches on immediately. In this case the first touch of the
button is ignored in respect to the normal function of that button.
Key lock
Pressing the MODE button (5) for longer than 3 seconds locks all the buttons (5-7) and
the potentiometer (1). The display shows “LOC” in alteration to the mode (changing
every 2 seconds). Pressing the MODE button again for more than 3 seconds unlocks
the button- and potentiometer-functions. Please note: If the display is in OFF-mode it
will take approximately 25 seconds before the display switches off. It will be switched
on again if any key is touched and will switch off again after 25 seconds if the keys are
not unlocked by the procedure mentioned above.
Termination
To avoid interference the last unit of a DMX-chain should be terminated. Therefore the
DIP switch (9) of the last unit in the DMX-chain must be switched ON.

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 12
“P” DMX Preset Mode
If you want to run the pre-programmed patterns and scenes by an external DMX-
controller you can use the DMX Preset Mode. Press the MODE button (5) until the
display shows “P”, indicating operation in “P” (DMX Preset) mode. Set the DMX starting
address by simply using the UP/DOWN buttons (6/7). The chosen DMX-address comes
effective approximately 3 seconds later and will show up on the display (2) in
alternation to the “P”.
The unit receives DMX values on a packet of four channels and mirrors the received
data on the DMX output (13). If a DMX signal is present the DMX LED (3) will turn on.
The four channels control the unit as follows:
If DMX-value of channel 3 is lower than 50 the unit works with static colours:
DMX Channel Value Range Function
CH1 000-255 Colour choice from presets (see “C” mode)
CH2 000-255 Dimmer
CH3 000-049 Static colour mode active
CH4 000-049 Strobe off
050-255 Strobe (050=slow / 255=max. speed 23 Hz)
Colour presets can be activated by means of CH1 whilst the chosen colour can be
dimmed by weighting the colour balance with CH2. If the value of CH4 is above 50 the
unit is set to strobe mode. The strobe speed for any fixed colour chosen on the first
channel can be adjusted from zero (value <50) to 23 flashes per second (value 255).
If DMX value of channel 3 is equal or higher than 50 the unit works in pattern mode:
CH1 Pattern CH1 Pattern
000-015 Soft fade red-green 136-150 Hard switch green-blue
016-030 Soft fade green-blue 151-165 Hard switch red-blue
031-045 Soft fade green-blue 166-180 Hard switch red-yellow
046-060 Soft fade red-yellow 181-195 Hard switch candy-lime
061-075 Soft fade candy-lime 196-210 Hard switch pink-blue
076-090 Soft fade pink-blue 211-225 Hard switch turquoise-pink
091-105 Soft fade turquoise-pink 226-240 Hard switch red-green-blue
106-120 Soft fade red-green-blue 241-255 Hard switch red-yellow-green
121-135 Hard switch red-green -turquoise-blue-pink
DMX Value range Function
CH2 000-255 Dimmer
CH3 050-255 Chase speed
CH4 000-049 Strobe off
050-255 Strobe (050=slow / 255=max. speed 23 Hz)
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 5
■Functional advice
This unit is immune to the presence of electromagnetic disturbances – both conducted
and radiated - up to a certain level. Under peak conditions, the unit is classified to show
a “class C” performance criteria and may encounter temporary degradation or loss of
function which may need manual help to recover. In such case, disconnect the AC
power from the unit and reconnect it again to recover.
■Environmental advice
This unit is build to conform to the ROHS standards and the WEEE
directive 2002/96/EC of the European Parliament and of the Council of
the European Union. Under these regulations, the product shall not be
discarded into regular garbage at the end of its life, but shall be returned
to authorized recycling stations.
■Unpacking
Please check that the box contains the following items:
Main parts: 1 pcs. PS020A main unit
1 pcs. mains cable
1 pcs. operation manual
Accessory parts: 1 pcs. Mounting cover
2 pcs. Mounting screw
1 pcs. connection cable to panel
If any part is missing, please contact your dealer immediately for replacement.
Note: Your dealer may have chosen to pre-assemble this product with any suitable of
Multiform’s LS series passive RGB LED panels for you. In this case, the above
accessory parts have already been used during assembly.
■Getting started: connecting/assembly
In case your dealer did not pre-connect/assemble the unit for you with any of
Multiform’s LS series passive RGB LED panels, you need to connect/assemble it
before use.
Risk of electric shock: Do not connect the mains cable before the
following steps are accomplished!
For assembly, there are two basic choices:

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 6
1) Fix the PS020A DMX-controlled 3-Channel power supply on a wall by using two
screws at the correct distance which do not protrude more than 4mm from the wall
surface. Fix the screws on the wall first, then slide the PS020A DMX-controlled 3-
Channel power supply on the screws using the slots on the rear side. Remove the
cover of the PS020A DMX-controlled 3-Channel power supply and fix the wall screws
through the holes provided in the units PCB. Re-fit the cover of the PS020A DMX-
controlled 3-Channel power supply. Plug the optional extended connection cable into
the PS020A DMX-controlled 3-Channel power supply on one side and the passive RGB
LED panel on the other side until the locking mechanism of the connector is secured.
Plug in the mains cable to the unit and verify the display shows “A1”. (NOTE: “A1” is
only shown if no external DMX signal is supplied to the unit). Connect external DMX
connections if any.
2) Fix the PS020A DMX-controlled 3-Channel power supply on the back of a Multiform
LS series passive RGB LED panel (see illustration below, showing LS1310). Fix the
screws to the LED panel into the provided mounting points first [1], leaving some
clearance to slide on the PS020A DMX-controlled 3-Channel power supply. Then slide
the PS020A DMX-controlled 3-Channel power supply on the screws using the slots on
the rear side [2]. Remove the cover of the PS020A DMX-controlled 3-Channel power
supply and fix the screws through the holes provided in the units PCB. Re-fit the cover
of the PS020A DMX-controlled 3-Channel power supply [3]. Plug the provided
connection cable into the PS020A DMX-controlled 3-Channel power supply on one side
and the RGB LED panel on the other side until the locking mechanism of the connector
is secured. Get the black plastic cap fixed at the top end to cover the cable and to fix
the power supply itself from sliding off. Use the two black screws [4]. Plug in the mains
cable to the unit and verify the display shows “A1”. (NOTE: “A1” is only shown if no
external DMX signal is supplied to the unit). Connect external DMX connections if any.
1 2 3 4
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 11
“SLA” DMX Slave Mode
Press the MODE button (5) until the display shows “SLA”, indicating operation in “SLA”
(SLAVE) mode. In this mode the unit is set to DMX-channel 001 in order to receive the
signals from a master-unit of the Multiform LS series being in mode "A" or "C". The unit
interprets CH1 as red intensity, CH2 as green intensity and CH3 as blue intensity. CH4
is not in use, and the potentiometer (1) is disabled.
This mode can also be used for remotely controlling the unit if no specific DMX address
is needed and channels 001-003 can serve as a default. To indicate that the unit is
controlled by an external DMX signal, the DMX LED (3) is lit.
“d” Mode (DMX Mode)
Press the MODE button (5) until the display shows “d”, indicating operation in “d”
(DMX) mode. Shortly after that, the display shows the DMX starting address. You can
choose any DMX starting address by simply using the UP/DOWN buttons (6/7). The
chosen DMX-address comes effective approximately 3 seconds later and will show up
on the display (2) in alternation to the “d”. This allows control of the unit by any external
DMX signal sending on the chosen channel.
In this mode the potentiometer (1) is disabled.
The unit receives DMX values on a packet of four channels and mirrors the received
data on the DMX output (13). If a DMX signal is present the DMX LED (3) will turn on.
The four channels control the unit as follows:
DMX channel Value Range Function
CH1 000-255 Red intensity
CH2 000-255 Green intensity
CH3 000-255 Blue intensity
CH4 000-127 Master dimmer
128-227 Strobe (128=slow / 227=max. speed 23 Hz)
228-255 Master dimmer full on, Strobe off
Addressing has to be done as follows:
001 first device (CH 1-4) *factory default*
005 second device (CH 5-8)
009 third device (CH 9-12)
013 fourth device (CH 13-16) and so on.
This setting is stored even if the device is switched off.

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 10
A16 Hard switch turquoise-pink Sound-to-light, Speed
A17 Hard switch red-green-blue Sound-to-light, Speed
A18 Hard switch red-yellow-green-turquoise-blue-pink Sound-to-light, Speed
A19 Random speed red-yellow (Fire) None
A20 Random speed green-blue (Ocean) None
A21 Random speed red-blue None
A22 Random speed red-green-blue (RGB) None
A23 White strobe Sound-to-light, Speed
A24 Red strobe Sound-to-light, Speed
A25 Green strobe Sound-to-light, Speed
A26 Blue strobe Sound-to-light, Speed
A27 Strobe chase red-green-blue Sound-to-light, Speed
“C” Colour Mode
Press the MODE button (5) until the first digit on the display shows “C”, indicating
operation in “C” (COLOUR) mode. Then choose by using the UP/DOWN buttons (6/7)
one of the 19 preset colours as shown in the list below. Changing the setting becomes
effective directly. Knob (1) determines the dimming level.
In “C” mode, the unit does not receive any values from the DMX input but generates
related DMX values on the output according to the selected pattern, so that other
similar units from the Multiform LS series of LED devices can show the same colour if
they are connected by DMX signal cables and set to Slave Mode “SLA”.
NOTE: The “C” Mode is automatically disabled and can not be chosen when an
external DMX signal is received [DMX indicator LED (3) is lit].
If you leave mode “C” for any reason and come back later into mode “C”, the unit will
recall the last chosen colour (even if the unit was switched off in between).
Available colour presets:
C 0 all off C10 Frog
C 1 Red C11 Lavender
C 2 Green C12 Candy
C 3 Blue C13 Peach
C 4 Yellow C14 Aqua
C 5 Pink C15 Leaf
C 6 Turquoise C16 Purple
C 7 Lime C17 Barbie
C 8 Orange C18 Breeze
C 9 Marine C19 White
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 7
■Getting started: choosing a location
Risk of fire: The PS020A DMX-controlled 3-Channel power supply has
been designed to work in dry indoor environments at environmental
temperatures up to 40 degrees Celsius. For proper operation, the
PS020A DMX-controlled 3-Channel power supply must be operated
with its heatsink side up, and unobstructed air convection to the
heatsink.
Do not:
- Operate the PS020A DMX-controlled 3-Channel power supply in
environments with more than 40 degrees environmental temperature or more
than 80% humidity.
- Operate the PS020A DMX-controlled 3-Channel power supply in any position
inclined or reclined more than 45 degrees from being upright (heatsink on top).
- Operate the PS020A DMX-controlled 3-Channel power supply in any closed
environment smaller than 10cbm, unless forced air convection is provided.

User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 8
■Operation
The PS020A DMX-controlled 3-Channel power supply supplies the necessary power to
the passive RGB LED Panel unit, plus provides all necessary functional control.
User interface overview:
1 In A-Mode: Speed Control (except A1 = Colour Mix Control)
In C-Mode: Dim-Level-Control
2 Display showing the Mode, DMX-address, LOC-function etc.
3 Indicates presence of a DMX signal
4 Indicates the sound-to-light mode (internal microphone)
5 MODE selection button
6 UP-button
7 DOWN-button
8 Internal microphone
9 Switches on the termination for the last unit in the DMX-chain
10 Switching the display on or off (with delay)
11 Maintenance (not in use)
12 Power-Input 85-240V AC
13 DMX-Output connector
14 DMX-Input connector
User Manual: PS020A DMX-controlled 3-CHANNEL Power Supply
V1.00 (06-2007) © Multiform, Leigh-on-Sea, UK 9
Upon the user’s choice, the unit can work stand-alone or may be controlled by external
DMX-controllers. Available modes:
“A” Auto Mode
Press the MODE button (5) until the first digit on the display shows “A”, indicating
operation in “A” (AUTO) mode. Then choose your desired pattern by using the
UP/DOWN buttons (6/7), see list below. Changing the setting becomes effective 1
second after the new setting is made to allow stepping through presets without
previewing all intermediate presets.
NOTE: The “A” Mode is automatically disabled and can not be chosen when an
external DMX signal is received [DMX indicator LED (3) is lit].
Whilst being in pattern A 1 (static scene), turning knob (1) determines the colour,
whereas being in one of the other 26 patterns, knob (1) controls the speed or selects
the sound-to-light function (refer to below pattern list). The sound-to-light function can
be activated by setting the knob (1) inside the first 10 degrees of its travel from left
detent and it works from a built-in microphone (8) which picks up the environmental
sound. Its activity is shown by the flashing of the right dot (4) in the display. The level
for all patterns is maximum.
In “A” mode, the unit does not receive any values from the DMX input, but generates
related DMX values on the output according to the selected pattern, so that other
similar units from the Multiform LS series of LED devices can show the same pattern if
they are connected by DMX signal cables and set to Slave Mode “SLA”.
If you leave mode “A” for any reason and come back later into mode “A”, the unit will
recall the last chosen pattern (even if the unit was switched off in between). Pattern list:
# Description Function of Knob (1)
A 0 All off none
A 1 Static scene Colour
A 2 Soft fade red-green Speed
A 3 Soft fade green-blue Speed
A 4 Soft fade red-blue Speed
A 5 Soft fade red-yellow Speed
A 6 Soft fade candy-lime Speed
A 7 Soft fade pink-blue Speed
A 8 Soft fade turquoise-pink Speed
A 9 Soft fade red-green-blue (RGB) Speed
A10 Hard switch red-green Sound-to-light, Speed
A11 Hard switch green-blue Sound-to-light, Speed
A12 Hard switch red-blue Sound-to-light, Speed
A13 Hard switch red-yellow Sound-to-light, Speed
A14 Hard switch candy-lime Sound-to-light, Speed
A15 Hard switch pink-blue Sound-to-light, Speed