MULTISPAN PIC-6004A User manual

ProductManual
PIC-6004A
JumboDisplay
MultispanControlInstrumentsPvtLtd
72/B,Phase1,GIDCEstate,Vatva,Ahmedabad-382445,Gujarat,India.
www.multispanindia.com
[phone]
[email protected]

Single display :- 165(H) X 380(W) X 50(D)mm
0 To 10V DC, 0 To 20mA DC , 4 To 20mA DC ( Selectable)
Single :- 100 To 250V AC, 50/60 Hz Approx 4VA
Dual :- 100 To 250V AC, 50/60 Hz Approx 7VA
Size
Range
Input
Power Supply
Page-1 www.multispanindia.com
PIC-6004A
TechnicalSpecification
Model No
Description
PIC-6004A
Micro controller based, Single Side & Dual Side Display
Display
Protection Level
(As per request) IP-65(Front side) AS per IS/IEC 60529:2001
-999 to 9999 (selectable)
1) Menu setting procedure,
(a) Parameter menu : press SET + key together.
2) Press key to confirm the change and to go to next step.
3) Press key to Save & Exit.
4) Auto-exit is for 10 sec. Menu exit without saving.
5) In Parameter menu, signal low level mode is for 4-20mA DC input only
(ampere range : 0-5mA DC)
6) In Parameter menu, range will be (-999 to 9999), reverse scaling possible
selected out of three.
Note Range & Decimal Point Selectable Reverse Scalling Possible
Dual display :- 165(H) X 380(W) X 75(D)mm
ENT
SET
Configuration
4 Digit 7 seg 4 Inch”, Red LED Display

Page-2 www.multispanindia.com
PIC-6004A
UserConfiguration
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
ENT
Press key
d p
L R N G
H r n g
f L T R
O F S T
C R F C
S L L
I n p
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
A 0. 0
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Input
Press
key to set value
Press
&keytosetvalue

Press
& key to set value
Press
& key to set value between 0.0 to 5.0
Press
& key to set value
Press
& key to set value
Press
& key to set value
(ampere range : 0-5mA)
Press key for
sec to save & exit
Decimal Point
Low Range
High Range
Filter time
Off-set
Correction Factor
+
-
(range: 999 counts)
(range: 0.1 sec to 10.0 sec)
+
-
(range: 999 counts)
Signal Low Level
only for 4-20mA
Select by key
0-10V DC
0-20mA DC
4-20mA DC
0 - 1 0 0 - 2 0
4 - 2 0
p a r a
9 9 9 9
P A S S
0 1 2 3
Process Value
Password
Password value
Parameter message
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press & key to set password value
.

www.multispanindia.com
PIC-6004A Page-3
ConnectionDiagram
Single Dual
Input:
Range:
0 To 10V DC
4 To 20mA DC
0 To 20mA DC
-999 To 9999
0 To 10V DC
I/P
0/4 To 20mA
DC
www.multispanindia.com
100
250V AC
~
50/60 Hz
7VA
!
L
N
7
6
5
4
3
2
1
+
-
+
Made in India
Made in India
www.multispanindia.com
Input:
Range:
0 To 10V DC
4 To 20mA DC
0 To 20mA DC
-999 To 9999
100
250V AC
~
50/60 Hz
4VA
!
I/P
+
+
-
0 - 10V DC
0/4 -20mA
DC
L
N
1
2
3
4
5
6
7

TestCertificate
Product:PROCESSINDICATOR
ModelNo.:PIC-6004A
Input:0to10VDC,0to20mADC,4to20mADC(Selectable)
Range:-999to9999(Selectable)
Supply:Single:-100to250VAC,50/60HzApprox4VA
Dual:-100to250VAC,50/60HzApprox7VA
Accuracy:±1%OfFSD
CalibratorUsed:ProcessCalibrater
CalibratorSr.No.:P-CAL1



WARRANTY
Q.A. Engineer
AHMEDABAD
**
Multispan Warrants that the product supplied here under this Test Certificate is
guranteed against our design, our manufacturing and our workmanship defects for a
time period of 12 Months from the date of product dispatch from our permises.
Multispan undertakes the responsibility to replace/repair the faulty product at our
company premises free of cost. The manufacturing liability is limited to the value of
goods supplied. Hereby, the manufacturer will take no responsibilities for whatsoever
any consequential damages claimed by the customer whatsoever. This warranty
certificate is required to be produced for obtaining any repair or replacement service
from the Manufacturer. The Manufacturer reserve right to determine the reason for
Defect/Damage, before providing service.
Page-4 www.multispanindia.com
PIC-6004A

Page-5 www.multispanindia.com
PIC-6004A
1) All safety related codifications, symbols and instructions that appear in this operating manual or
on the equipment must be strictly followed to ensure the safety of the operating personnel
as well as the instrument.
2) If all the equipment is not handled in a manner specified by the manufacturer,
it might impair the protection provided by the equipment.
3) Read complete instructions prior to installation and operation of the unit.
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing
the wiring arrangement.
2) Do not touch the terminals while power is being supplied. To reduce electromagnetic interference,
use wire with adequate rating and twists of the same of equal size shall be made with shortest
connection.
3) A better anti-noise effect can be expected by using standard power supply cable for the
instrument.
1) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the
product or else it may lead to a safety hazard that may in turn endanger life or cause electrical
shock to the operator.
2) Use and store the instrument within the specified ambient temperature and humidity ranges
as mentioned in this manual.
3) Prior to the installation of this product, the installation instructions must be read and completely
understood. Keep these installation instructions in an easily accessible location for future reference.
Proper installation procedure by a qualified service technician must be followed, as outlined in
these installation instructions. Failure to do so could result in property damage, serious personal
injury, or even death.
4) Safety measures must be practiced at all times during the assembly of this product.
5) Use proper safety equipment and tools for the assembly procedure to prevent personal injury
Be aware of the mounting environment.
6) If drilling and/or cutting into the mounting surface, always make sure that there are no electrical
wires in wall.
7) Cutting or drilling into an electrical line may cause serious personal injury.
8) Make sure there are no water or natural gas lines inside the wall where the mount is to be located.
9) Cutting or drilling into a water or gas line may cause severe property damage or personal injury.
10) Do not install near sources of high heat. Do not install on a structure that is prone to vibration,
movement or chance of impact.
Risk of electric shock, Hazard Warning
!
1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth.
3) Do not use isopropyl alcohol or any other cleaning agent.
4) Fusible resistor must not be replaced by operator.
Safety Precautions
Warning Guidelines
Installation Guidelines
Maintenance

www.multispanindia.com
PIC-6004A
BC
D
A
A
165mm 380mm 50mm 165mm
BC
D
MODEL
DIMENSIONS
MechanicalInstallation
9 9 9 9
Page-6
Process
PIC-6004A
ENT
SET
Single
Dual
1)Theequipmentinitsinstalledstatemustnotcomeincloseproximitytoanyheatingsource,
causticvapors,oilssteam,orotherunwantedprocessbyproducts.
2)Donotconnectanythingtounusedterminals.
BC
D
A
A
165mm 380mm 75mm 165mm
BC
D
MODEL
DIMENSIONS
9 9 9 9
Process
PIC-6004A
ENT
SET
Input:
Range:
0 To 10V DC
4 To 20mA DC
0 To 20mA DC
-999 To 9999
0 To 10V DC
I/P
0/4 To 20mA
DC
www.multispanindia.com
100
250V AC
~
50/60 Hz
7VA
!
L
N
7
6
5
4
3
2
1
+
-
+
Made in India
Made in India
www.multispanindia.com
Input:
Range:
0 To 10V DC
4 To 20mA DC
0 To 20mA DC
-999 To 9999
100
250V AC
~
50/60 Hz
4VA
!
I/P
+
+
-
0 - 10V DC
0/4 -20mA
DC
L
N
1
2
3
4
5
6
7

www.multispanindia.com
PIC-6004A Page-7
Productimprovementandupgradeisaconstantprocedure.SoformoreupdatedoperatinginformationandSupport,
PleasecontactourHelping:[phone]/76/82orEmailat[email protected]Ver:2006
Note:-