MULTISPAN PIC 9004 User manual
Product Manual
PIC 9004
Jumbo Display
MultispanControlInstrumentsPvtLtd
72/B, Phase 1, GIDC Estate, Vatva, Ahmedabad-382445, Gujarat, India.
www.multispanindia.com
+91-9978991482
Parameter
Page-1 www.multispanindia.com
PIC-9004
Technical Specification
Model PIC-9004
Upper 6 Digit 7 Segment LED Display 2.25” inch in red colour
Upper 4 Digit 7 Segment LED Display 2.25” inch in green colour
Micro controller based, Single display
160(H) X 375(W) X 50(D)mm
Single Channel Encoder NPN/PNP Selectable
1 Relay 1C/O 230V AC, 5A
100 To 270V AC,50/60 Hz, Approx 7VA
Front & Back
Display
Size
Input
Output
Power Supply
Reset
Protection Level
(As per request) IP-65(Front side) AS per IS/IEC 60529:2001
FUNCTION DISPLAYS
Set Diameter
Set PPR
Set Length
Decimal Point
Set Time
RANGE
0-9999.99 mm
0001 To 9999
0 to 999999 Meter
dIa
set
PPR
dp
tIme
999.999/9999.99/
99999.9/999999
00.1 to 99.9 sec.
Page-2 www.multispanindia.com
PIC-9004
Power On Instrument
Total Length in mtr
Speed in mtr/min
Set Length
Set Diameter
Set PPR
Set Time
Set Decimal Point
Range: 00000.1 to 999999 meter
Range: 0000.01 to 9999.99 mm
Range: 0001 to 9999 mm
Range: 00.0 to 99.9 sec.
Range: 999.999, 9999.99,
99999.9 & 999999.
1 2 3 4 5 6
9 9 9 9 9 9
9 9 9 9 9 9
0 0 0 1
9 9 9
0 0 0 0 0 0
1 2 3 4
s e t
d I A
P P R
T I M E
D P
Press key
Press key
Press key
Press key
Press key
Press key
SET
SET
SET
SET
SET
SET
Press keyto Save & Exit.
ENT
RST
Press & To Change Parameter
Press & To Change Parameter
Press & To Change Parameter
Press & To Change Parameter
Press To Change Parameter
Procedure to program
Page-3 www.multispanindia.com
PIC-9004
Working
Note
1). Length of Material ( in meter ) for one revolution = 3.14 X Diameter (mm)
2). Total length = { 3.14 X Diameter (mm) X Number of Revolutions } / 1000
3). Total Meters/Minute = { 3.14 X Diameter (mm) X RPM } / 1000 X PPR
4). If PPR is set other then 1, Non pulse counting will be divided by set value of PPR
1). When pulse comes from sensor, upper display indicates increment in ‘Total Length’ in
Meter Lower Display indicates ‘Speed’ in Meter/Min.
2). When encoder rotates in clockwise direction count will increment.
3). For Manual Mode, set time = 00.0 sec & For Auto Reset Mode,
set time = 00.1 to 99.9 sec.
4). When Total Length = Set Length, relay energise. Relay remains ON for
Auto Reset Time.Relay turns off after completion of time. If time is set at 00.0 sec.
then relay remains ON until key is pressed.
5). If there is a power failure the last reading is stored in the memory and Counter starts
resume counting from the last stored value, when power ON.
6). To restart Totalizing or to Reset press key. Upper display will show 00000.0 and the
counting will restart.
7). Press key to show number of Batches.
ENT
RST
ENT
RST
Page-4 www.multispanindia.com
PIC-9004
Connection Diagram
Note:
PNP ENCODER:- Short Pins 5 & 6
Encoder Connection to 3,4 & 5
NPN ENCODER:- Short Pins 3 & 4
Encoder Connection to 4,5 & 6
1
L
N
100
270V AC
~
50/60 Hz
7VA
2
3
4
5
6
7
8
9
10
11
12
13
Made in India
www.multispanindia.com
RELAY
NC
NO
C
+12V
I/P1
I/P2
RESET
GND
!
Page-5 www.multispanindia.com
PIC-9004
TestCertificate
Product : Length Counter
Model No.: PIC-9004
Input: ENCODER NPN/PNP
Range : 0-999999 MTR
Output: 1R1C/O
Supply: 100 to 270V AC,50/60Hz,APPROX 7VA
Accuracy: 1% of FSD
Accuracy : ± 1 % Of FSD
Calibrator Used : Pulse Generator
Calibrator Sr. No . : PG-5
WARRANTY
Q.A. Engineer
AHMEDABAD
**
Multispan Warrants that the product supplied here under this Test Certificate is
guranteed against our design, our manufacturing and our workmanship defects for a
time period of 12 Months from the date of product dispatch from our permises.
Multispan undertakes the responsibility to replace/repair the faulty product at our
company premises free of cost. The manufacturing liability is limited to the value of
goods supplied. Hereby, the manufacturer will take no responsibilities for whatsoever
any consequential damages claimed by the customer whatsoever. This warranty
certificate is required to be produced for obtaining any repair or replacement service
from the Manufacturer. The Manufacturer reserve right to determine the reason for
Defect/Damage, before providing service.
Page-6 www.multispanindia.com
PIC-9004
1) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
2) Do not connect anything to unused terminals.
BC
D
A
A
160mm 375mm 50mm 160mm
BC
D
MODEL
DIMENSIONS
Mechanical Installation
0 1 5 0 0 0
5 2 5. 0
SET ENT
RST
PIC 9004
Made in India
www.multispanindia.com
1
2
3
4
5
6
7
8
9
10
11
12
+12V
L
N
100
270V AC
~
50/60 Hz
7VA
GND
RESET
I/P2
NC
C
NO
RELAY
!
I/P1
Page-7 www.multispanindia.com
PIC-9004
Product improvement and upgrade is a constant procedure. So for more updated operating information and Support,
Note
Table of contents
Other MULTISPAN Monitor manuals
