Multivoice Mv-audible User manual

Add more sound Changing channels

Connect headset

Turn me on

…Twist 1/4—turn to

Lock into place.

NOTE: You must have eight (8) or fewer Intercoms synchronized in a

MULTIVOICE network for each unit to have a “live” microphone. If you

are using 8 or fewer Intercoms, you can activate the mic by A) flipping

the switch on the Switch-to-Talk™ box between your Headset and

Intercom, or B) by pushing the microphone button on the front of the

Intercom, or C) by lowering the boom microphone on your Headset.

Repeat Steps 1—3 above to add more MULTIVOICE Intercoms to your

network system.

Press to

Increase

Volume

Channel Button

Press to

Decrease

Volume

…with the Pin inside the Male Connector

on the Intercom.

123Activate mic

4 5 6

NOTE #1: After you release the Power Button, the LED Light will

begin to ash again. This is normal.

NOTE #2: To TURN OFF a MULTIVOICE Intercom, press and hold the

Power Button until all Lights on the Intercom turn o. Your Intercom is

now turned o.

NOTE #3 FOR FOOTBALL USE:

f you plan to use 1 or more MV-AUDIBLE

Intercoms in a Press Box during a game or practice, you must ensure

that A) You turn on these Intercoms first, and B) that you only use them

in the Press Box during said game/practice. Failure to do so may cause

temporary loss of communication.

NOTE: Each additional MULTIVOICE Intercom will be connected

to the other units in your system as soon as you complete the

steps in Section #1 above.

NOTE: If one of the Channel LED Lights are lit on your MULTIVOICE

Intercom, you will hear everyone speaking on that particular Channel.

If you want to BE HEARD

TM by others on that same Channel, the 2 Blue

LED Lights on the front of your Intercom must also be lit. To enter Talk

Mode, please push the mic button, ip the switch on the

Switch-to-Talk

box, or lower your boom mic so it is positioned in front of your mouth;

the Blue LEDs will light-up and you can now BE HEARD. To deactivate

your mic and return to Listen Mode, push the mic button or lift your

boom mic; the Blue LED Lights will now turn o.

NOTE: MULTIVOICE Intercoms come standard with 4-6

Channels, (4 channels for MV-AUDIBLE and 6 channels for

MV-NEXUS and MV-PROTECTOR) with each Channel LED Light

signifying the respective Channel, starting (from Left to Right)

with Channel #1 and ending with Channel #4 for MV-AUDIBLE

and Channel #6 for MV-NEXUS and MV-PROTECTOR. To change

from one Channel to the next, simply push the Channel Button

once. (See section #7 on the back page for more info.)

Example: Channel 2

Connect one cable headset to a MULTIVOICE Intercom as shown below.

Choose 1 Intercom and . . .

Light will flash, then turn solid.

After Light turns solid,

release Power Button.

Push & Hold the Power Button.

Then push the cable Connector

Down and…

Align the Female Connector on the

Cable Slot…

QuickStart Guide multivoice™ Intercoms

MV-AUDIBLE™, MV-NEXUS™ and MV-PROTECTOR™

Once a cable headset is connected to a MULTIVOICE Intercom, the

default setting is for the microphone to be turned on. You will know

your mic is “live” because the Blue LED lights on the front of your

Intercom are lit.

9troubleshooting

7Everyday use

8recharging

MULTIVOICE, MV-AUDIBLE, MV-NEXUS, MV-PROTECTOR, BE HEARD and the MULTIVOICE marks and logos are each trademarks of MULTIVOICE. TM

MULTIVOICE Intercoms operate without a Base Station, so setup takes mere seconds. MULTIVOICE Intercoms also support an unlimited number of users, with up to 8 Talk Slots on a

single group system. And militarygrade MULTIVOICE Intercoms deliver up to 18 hours of Talk Time in any weather at up to 4,000 feet.

MULTIVOICE Intercoms come standard with 4-6 channels, with each Channel LED Light signifying the respective Channel, starting (from Left to Right) with Channel #1 and ending

with Channel #4 for MV-AUDIBLE and Channel #6 for MV-NEXUS and MV-PROTECTOR Intercoms. By default, each user starts on Channel #1. Each time you push the Channel button,

you will switch to a new Channel and hear 1 or more tones in your headset signifying what Channel you have joined: for example, 2 tones for Channel 2; 3 tones for Channel 3; etc.

Additionally, the corresponding Channel LED Light will also be lit.

A. If your headset cable is properly connected to your MULTIVOICE Intercom and the Channel LED Lights are not lit, your intercom has been inadvertently turned o. Please restart

your intercom by following the steps in Sections 1, 2 and 3 on the front page. This should rectify the problem.

B. If you can no longer hear anyone in your headset, rst verify that your headset is properly connected to your MULTIVOICE Intercom. If not, reconnect the headset cable. This

should rectify the problem.

C. If your headset cable is properly connected to your MULTIVOICE Intercom but the Channel LED Lights are ickering, turn o your intercoms outlined in Note #2 in section 1. Then

restart your intercom by following the steps in Sections 1, 2 and 3 on the front page. This should rectify the problem.

D. If you can hear people speaking in your headset but they cannot hear you, rst verify that the 2 Blue LED Lights on the front of your Intercom are lit. If not, please follow the steps

in Section 3 to activate your microphone. If this does not rectify the problem, please contact MULTIVOICE at 385-236-5111.

E. If (1) your microphone button is pushed and (2) your microphone is lowered and properly adjusted in front of your mouth and (3) you can hear people speaking in your headset

but they cannot hear you, please verify that the Blue LED Lights on the front of your MULTIVOICE Intercom are lit. If not, please turn o your Intercom by pressing and holding the Power

Button until all LED Lights turn o. Then restart your Intercom as outlined in Sections 1, 2 and 3 on the front page. This should rectify the problem.