muuto IN SITU User manual

NEW PERSPECTIVES  SCANDINAVIAN DESIGN
— Anderssen & Voll
IN SITU
DULAR
SOFA

ASSEMBLY INSTRUCTION
CONTENT
Straight Frame Section Assembly 
Straight Frame Section to Module 2
Straight Frame Section to Multiple Modules 3
Lower Linking Bracket on Straight Configuration 4
Upper Linking Bracket on Straight Configuration 5
Straight Configuration to Straight Configuration 6
Corner Frame Section Assembly 7
Corner Frame Section to Module 8
Lower Linking Bracket on Corner Configuration 9
Upper Linking Bracket on Corner Configuration 0–
Corner Configuration to Corner Configuration 2 Screw 2
4 pcs. per module
Bar
(Always 2 of same length).
Size and amount depends on
frame section/configuration
Leg
(Always 2 of same length).
Size and amount depends on
frame section/configuration
Screw 
16 pcs. per
frame section
STRAIGHT FRAME SECTION ASSEMBLY
With screw , fasten legs to bars
as illustrated.
Screw 
16 pcs. per
frame section
Incorrect Correct

 STRAIGHT FRAME SECTION TO MODULE
With screw 2, attach the whole frame section to the
individual module as illustrated.
STRAIGHT FRAME SECTION TO MULTIPLE MODULES
Starting from one side/end of the frame section attach
the individual modules loosely, witout leaving any gap
in between as illustrated using screw 2.
When all modules are attached, secure the modules
by tightening the screws. Each Module is fastened with
4 screws and some holes in bars might not be used.
Number of modules and screws depend on the
configuration. Hole pattern in bars depends on the
order of chosen modules.
Screw 2
4 pcs. per module
Screw 2
4 pcs. per module

 LOWER LINKING BRACKET
ON STRAIGHT CONFIGURATION
UPPER LINKING BRACKET
ON STRAIGHT CONFIGURATION
With screw 2, attach the upper linking brackets as
shown. Make sure to always face one up and one down.
NOTE — The smallest section/the section with the
fewest modules, should always have the upper linking
bracket facing upwards.
Use screw  x 2 to attach the lower linking bracket as
illustrated to one fully assembled section.
NOTE — The smallest section, or the section with
the fewest modules, should always have the the lower
linking brackets attached first.
CONTENT
Screw 2
4 pcs. per kit.
Upper
linking brackets
2 pcs. per kit
Lower
linking bracket
1 pcs. per kit
Screw 
 pcs. per kit.
Screw 
 pcs. per kit.
Screw 2
4 pcs. per kit.
Facing up Facing down

 STRAIGHT CONFIGURATION
TO STRAIGHT CONFIGURATION
Link the upper brackets as shown, and secure the
lower linking brackets with the remaining screws  x 2
underneath.
CORNER FRAME SECTION ASSEMBLY
CONTENT
Screw 2
4 pcs. per module
Bar
(Always 2 of same lenght).
2 pcs. per corner frame section
Single leg
4 pcs. per corner
configuration
Screw 
16 pcs. per
corner frame section
With screw , fasten legs to bars as illustrated.
Screw 
16 pcs. per frame
section
Screw 
 pcs. per kit.

 CORNER FRAME SECTION TO MODULE
With screw 2, attach the whole frame section to the
induvidual module as illustrated.
Screw 2
4 pcs. per module
LOWER LINKING BRACKET
ON CORNER CONFIGURATION
Use screw  x 2 to attach the lower linking bracket as
illustrated to one fully assembled section.
NOTE — When assembly a corner configuration, the
Lower Linking bracket must always be mounted on
the adjacent configuration.
CONTENT
Screw 2
4 pcs. per kit.
Upper
linking brackets
2 pcs. per kit
Lower
linking bracket
1 pcs. per kit
Screw 
 pcs. per kit.
Screw 
 pcs. per kit.

0 UPPER LINKING BRACKETS
ON CORNER CONFIGURATION
With screw 2, attach the upper linking brackets as
shown. Make sure to face both brackets upwards.
NOTE — When assembling a corner configuration, the
Upper Linking brackets on the adjacent configurations
must always be mounted facing upwards.
With screw 2, attach the upper linking brackets as
shown. Make sure to have both sides facing down.
NOTE — When assembling a corner configuration,
the Upper Linking brackets on both sides of the
Corner configuration must always be mounted
facing downwards.
NOTE —
Lower brackets on
both side of the
Corner configuration
Screw 2
4 pcs. per kit.
Screw 2
4 pcs. per kit.
Facing downFacing downFacing upFacing up

 CORNER CONFIGURATION
TO CORNER CONFIGURATION
Link the upper brackets as shown, and secure the
lower linking brackets with the remaining screws  x 4
underneath.
Facing up Facing up

MUUTO HEAD OFFICE
ØSTERGADE 36-38, DK-1100
COPENHAGEN, DENMARK
FOR MORE INFORMATION
VISIT MUUTO.COM
CLEANING RENGØRING SÄUBERN NETTOYAGE LIMPIEZA
EN To remove stains from a textile-upholstered sofa, use foam from a mild mixture
of water and detergent.
DK Brug skummet fra en mild blanding af vand og opvaskemiddel til at fjerne pleer
på en tekstil polstret sofa.
DE Zum Enernen von Flecken auf gepolsterten Sofas verwenden Sie den Schaum
aus einer Wasser-Spülmiel-Mischung.
FR Pour retirer les tâches du textile sur les canapés, utilisez de la mousse depuis un mélange
d’eau douce et du détergent.
ES Para eliminar las manchas del tapizado textil de los sofás, utilice una solución
de agua jabo-nosa neutra.