My LED Lighting Guide MLLG-AX-LED-HM450-5000-U User manual

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
IMPORTANT INSTALLATION INFORMATION
2.Before commencing installation or maintenance, ensure
electricity is switched off at the mains. Installation or
maintenance should be carried out by a qualified electrician.
3.The luminaire must not, under any circumstances, be
installed directly to flammable materials, and luminaires
must not be covered with any flammable materials.
4.Mounting height range of 0 to 40 meters, this model is
suitable for outdoor lighting.
5.Ensure there is adequate free air circulation of at least
50cm around the luminaire. All luminaires run hot. It is
the installer's responsibility to consider fire risk and take
appropriate precautions.
LEAVE A COPY FOR THE USER / MAINTENANCE ENGINEER
FOR FUTURE REFERENCE
12
U-bracket
U-bracket
locking screws
Mains power supply
Facade or other
mounting surface
U-bracket
STEP 1:
Unscrew screws from the yoke mounting bracket using an Allen .
See Figure 1.
STEP 2:
Get the mains power supply cord through wiring hole on U bracket, then
fix U bracket to facade or other location using swelling bolts or other screws.
See Figure 2.
3
Locking screw
Locking washer
Securing plate
4
Junction Box
5
U-bracket
locking screws
STEP 3:
Fit lightbody into the hooks of U-bracket, and make sure the
locking washers must be located between U bracket the lightbody.
See Figure 3.
STEP 4:
Tighten the screws slightly, rotate the lightbody and make it easier for wiring,
then connect mains power supply to the power cord of lightbody,
See Figure 4.
For more details about wiring, please refer to the wiring instruction
to compete wiring, see Figure 7.
STEP 5:
Loosen the screws on both sides of U bracket, rotate the lightbody
to a specific aiming direction for illumination, finally lock the screws
at 45 N.m torque to complete installation.
Installation Instruction & Installation Steps
6
Mounting C:
OPTIONAL MOUNTING with Suspension rope: Hang the thimble secured
by an eyesplice on the hook.
Stainless steel
hanging wire
Hook
LED Flood/Area Light
INSTALLATION INSTRUCTION
MLLG-AX-LED-HM-600-5000-U
1.Normal operating environment and temperature: -40℃－+50℃.
Fixtures is suitable for Airport, Car Dealerships, Achitural,
Factory, Warehouse, High Mast lighting and stadium lighting.
H
W
L
Drawings herein for MLLG-AX-LED-HM-600-5000-U are used as examples for the below listed models.

Safety Notice
Alternating Current
Terminal Block
LIVE
GROUND
NEGATIVE
LIVE - Black
NEGATIVE - White
GROUND-Housing
LED DrivER
Mains power supply
Electrical Connections
L
G
N
Input wire H07RN-F 3x1.5mm² or rubber sheathed cable (not supplied).
Conductor must have a minimum cross-sectional area of 1.5mm² .
STEP I: Connect the LINE wire in the mains power supply cord to black LINE
wire from lightbody via a terminal block.
STEP II: Connect the NEUTRAL wire in the mains power supply cord to white
NEUTRAL wire from lightbody via a terminal block.
STEP III: Connect the green grounding wire in the mains power supply cord to
green grounding wire from lightbody via a terminal block.
***IF THERE IS JUNCTION BOX IN CEILING:
STEP III: Push back the connected wires into junction box.
STEP I: Open the lid of the external junction box.
STEP II: Connect the LINE wire in the mains power supply cord to the L marked
hole In the terminal block from the external junction box, and tighten the
connection properly.
STEP III: Connect the NEUTRAL wire in the mains power supply cord to the N
marked hole in the terminal block from the external junction box, and tighten
the connection properly.
***EXTERNAL JUNCTION BOX:
STEP IV: Connect the YELLOW/GREEN GROUNDING wire in the mains power
supply cord to the G marked hole in the terminal block from the external junction
box, and tighten the connection properly.
STEP V: Close the junction box, and fasten the screws to fix the lid to the junction
box body.
This logo indicates that this product must not be disposed of with other waste.
Please recycle used lamps to prevent environmental hazard and threats to human
health resulting from improper disposal.
Common causes and solution
Encountered Problem
Possible Cause
Remedy
Module does not light up
Internal wire disconnected
Open fixture and locate loose wires, reconnect connectors or wires and close
cover. And retest.
LED driver failure
Open fixture and check for disconnected wiring. If all wires are fine, replace LED
driver with new one and test.
Module Failure
If all the above remedies are trialed then the light module has most likely failed.
Contact us for replacement and warranty information.
WIRING INSTRUCTION
7
Model No.
No. of leds
System Wattage
Dimensions (L x W x H)
Net Weight
Working Environment
IP
MLLG-AX-LED-HM-
450-5000-U
216
485W
622 (24.49" ) x 680 ( 26.77" ) x 112 mm ( 4.41" )
19.96kg(44.00Ibs)
-40℃-+50℃
IP67
MLLG-AX-LED-HM-
600-5000-U
288
645W
742 (29.21" ) x 680 ( 26.77" ) x 112 mm ( 4.41" )
23.06kg(50.84Ibs)
MLLG-AX-LED-HM-
750-5000-U
360
802W
922 (36.30" ) x 680 ( 26.77" ) x 112 mm ( 4.41" )
27.5kg(60.63Ibs)
MLLG-AX-LED-HM-
900-5000-U
432
964W
1042 (41.02" ) x 680 ( 26.77" ) x 112 mm ( 4.41" )
30.98kg(68.30Ibs)
Input Voltage:120-277VAC 50/60Hz Mounting U&C
Main specifications: