Myron&davis NV7CRV1 User manual

Installation Instructions
http://www.myronanddavis.com
Honda CR-V NV7CRV1
INSTALLATION INSTRUCTIONS AND USE
The Myron & Davis In-Dash Navigation System includes
a built in DVD player that should not be viewed by the
driver while driving to avoid violation of State and Local
Laws. This product should be installed by a professional
to ensure proper installation and operation.
Myron & Davis is not responsible for any potential accidents,
property damage or bodily harm resulting from improper
installation or operation.

Myron and Davis Entertainment Systems
Multi-Media Navigation System Installation Guide NV7CRV1 Rev A
- Read the entire installation instructions prior to performing any work .
- Before installation, check to see that all parts are not damaged or defective.
1 - Ensure all appropriate materials are available
Installation tools needed:
- Digital Multi – Meter
- Philips screwdriver set
- Trim Removal tools
- ¼” drive sockets
- Torx or Allen wrenches
- A functional DVD or CD

Installation Instructions
2- Caution
-Battery
Check the battery to ensure it is fully charged.
NOTE: Some new vehicles batteries are not fully charged and may cause improper
operation
3 - Warning
- Remove the key from the ignition
- Disconnect the negative battery terminal
- Care must be used working with vehicles with airbags to prevent:
- injury
- damage to or malfunction of the airbag system
- work on malfunctioning systems or components must be performed by certied
- technicians
4 - Removal Of The Dash Trim
Use caution when removing dash trim components as not to damage or mar the
surfaces or damage the fasteners.
-Inspect all fasteners for damage and replace as necessary

OEM Dash Step 1 - Carefully use a pick tool
to loosen trim piece above AC
vents
Step 2- Lift up and remove trim piece
Step 3 - Remove AC Vents
Step 4 - Loosen gear shift lever
trim
Step 5 - Remove AC controls
AC Vents and controls removed
Step 5 - cont’d
4 – Removal Of The Dash Trim Cont’d.

Step 1- Remove the 4 screws
securing the factory radio
Step 2 - Remove the factory radio
Step 4 - Unplug factory wiring
harness cont’d
5 – Removal Of The OEM Radio
Remove the OEM Radio and prepare the Myron and Davis Unit for installation by
following the steps below.
Note: Inspect all fasteners and brackets for damage. Replace as necessary before the
installation process is started.

Step 1 - Mount the GPS and
Satellite Radio antenna on
the exterior of the vehicle
Step 2 - Connect the optional
Satellite Radio Tuner as
shown below
Step3 - Mount the iPod /
Satellite Radio interface
module in a convenient
location
Step 4 - Position the iPod
interface connector
conveniently for end user use.
The GPS and Optional Satellite Radio Antenna should be mounted on the exterior
of the vehicle and optional iPod interface connector in a user friendly location
within the vehicle cabin. Follow the steps below for proper installation.
Note: Avoid routing the GPS harness near to other power sources to ensure
peak operation
6 - Satellite Radio, iPod interface and GPS Antenna
Note: The installer is responsible to route harnesses not to aect the vehicle
safety systems and system installation. Harmnesses must be routed away from airbags
and other safety systems

Step 4: Prepare vehicle
harnesses
Step 2 - Connect Myron and Davis
harness to factory harness
Step 3- Connect antenna harnesss
Step 4 - Connect blue power antenna
cable
Step 5 - Install mounting brackets Step 6 - Install Myron and Davis unit
Step 1 - Remove DVD Player transport
screws
7 - Connecting and installing the Myron & Davis unit
Follow the steps below to ensure proper installation and connection of the Myron & Davis
unit.
Note: To ensure that the video cannot be viewed when the vehicle is in motion,
connect the (blue/white) Brake Wire to the Emergency Brake Switch
(grounded when engaged).
Note: Carefully route the wire harnesses so they cannot be damaged during the
installation process of the Myron and Davis unit.

Step 4 - Verify Unit operation
Step 6 - cont’d
Step 1 - Replace gear shift lever trim Step 2 - Replace AC controls Step 3 - Replace AC vents and top trim
piece
Replace the dash trim in reverse order of removal. Use care not to damage
or mar the surfaces.
8 – Re-installing the Dash Trim

http://www.myronanddavis.com 1425 Cooley Court, San Bernardino, CA 92408 Toll Free: 886.335.6789 Fax: [phone]