NAG SNR-MPX-16E1-SFP User manual

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
16E1 + 1Ethernet Fiber Optical Multiplexer
User’s Manual

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 1 of 16
To users：
：：
：
Thank you for using our products. Before using, please read this Reference Manual
carefully, and keep properly.
Alarm
1. This product cannot be caught in or be affected with damp, for they can make the
performance degressive and even broken.
2. Before fixing this product, please check the model and according to the User s’
Reference Manual.

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 2 of 16
Contents
CHAPTER 1 GENERAL INTRODUCTION........................................3
1.1 P RODUCT D ESCRIPTION .............................................................................3
1.2 P RINCIPLE C HART AND D ESCRIPTION ..........................................................3
1.2.1 Description........................................................................................4
1.3 C HARACTERS ............................................................................................4
CHAPTER 2 FUNCTIONS ..........................................................5
2.1 F RONT P ANEL ...........................................................................................5
2.1.1 LED...................................................................................................5
2.1.2 Buttons in front panel........................................................................6
2.1.3 Hot line phone (optional port)............................................................6
2.1.4 Front panel DIP definition .................................................................7
2.2 R EAR PANEL .............................................................................................9
2.2.1 Power Supply....................................................................................9
2.2.2 Ethernet (optional component)..........................................................9
2.2.3 Fiber interface.................................................................................10
2.2.4 E1 interface （ 75Ω ： BNC ） ..........................................................10
CHAPTER 3 PARAMETERS AND INDEX......................................11
3.1 P ARAMETERS ..........................................................................................11
3.1.1 Fiber interface.................................................................................11
3. 1.2 E1 interface....................................................................................11
3.1.3 10/100Base-T Port..........................................................................11
3.2 D IMENSION .............................................................................................11
3.3 P OWER SUPPLY .......................................................................................11
3.4 O PERATION C ONDITION ...........................................................................12
CHAPTER 4 OPERATION ........................................................13
4.1 E QUIPMENT INSTALLATION .......................................................................13
4.2 Q UICK INSTALLATION ...............................................................................13
4.3 C AUTIONS ABOUT INSTALLATION ..............................................................14
CHAPTER 5 PACKAGE........................................................... 15

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 3 of 16
CHAPTER 1. GENERAL INTRODUCTION
1.1 Product Description
16E1 + 1Ethernet Fiber Optical Multiplexer can multiplex to 16 E1 signals for
transmission over an optical fiber, resulting in reaching a longer distance without a repeaters
and superior performance compared to copper media.
16E1 + 1Ethernet Fiber Optical Multiplexer is the 16E1 point-to-point optical transport
equipment that uses the FPGA chips and it is easy to upgrade. It is single board structure
and the largest transmission capacity is 16E1. The outer design use the standard 19 inches
rack, so the volume is little, weight is light and operation is convenient and credit.
16E1 + 1 Ethernet Fiber Optical Multiplexer uses the PDH fiber transmission
technologies. The 2Mbps (E1) interfaces can connect with the exchanger, light loop device
and multi-diplexer directly to the special network. Complete alarm function for 16E1 Fiber
Optical Multiplexer, it is stable and easy to maintenance, install and small in size. It has one
digital service telephone.
1.2 Principle Chart and Description
Fig1. PDH principle chart

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 4 of 16
1.2.1 Description
Device adopts veneer structure, and can be distinguished according to the functions into 5
parts: A. 2/8 combine unit, B. encode/decode unit, C. hot line unit, D. monitoring system, E.
second power. A, B and E are the basic parts, achieving reverse conversion from 4
2048kbit/s signals to laser signal. C and D are of assistant.
1.3 Characters
•Base on IC of independence intellectual property rights
•Adopt veneer structure
•Offer 16 × 2Mb/s digital interfaces
•Up to 16E1 links on one fiber
•One link to service telephone for duty contract
•Provides 1 channel of 10M/100M, support VLAN setting.
•One channel OA for optional.
•When fiber signal is loss, users can distinguish whether the remote device is power
off or the fiber line is down from the indicator status on the local device.
•180-260VAC & -48VDC power options and the positive and negative of DC-48V can
be optional because there is the self-test circuit for the polarity inside th1e device
•Standard 19 inches rack, little volume, light weight, steady capacity and convenient
setup

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 5 of 16
CHAPTER 2. FUNCTIONS
2.1 Front Panel
Fig2. Sketch map of the front panel
2.1.1 LED
No. Name Status Describe
1 LOS1~16 Active E1 loss
2 OPLOS Active Optical Signal lost
Flick 2time/sec.: the remote device is power off
3 OPLOF Active Optical SYNC loss
4 E3 Active Optical BER≥10
-3
5 F2 Active Slave fiber line active, and the master down
6 PWR Active Power on
7 LINK/ACT
On/ Flick LAN Linked/ transmission
8 DUP On Full duplex
9 10M/100M
On Rate: 100M
10 1000M \ \
others
Reserved for no use.
Note: If the function is defined as 4E1/2E1, then LOS5-8/LOS3-8 is ineffective.

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 6 of 16
2.1.2 Buttons in front panel
PUSH OFF ON
MSK DIP1-5 be used E1 warning shield DIP1-5 be used E1 remote loop
MUTE (standalone) warning voice is on
(standalone) warning voice is off
LRS LED means Local LED means Remote
PH Hot line phone not used Use Hot line phone
2.1.3 Hot line phone (optional port)
Hot line phone, not occupy 2Mbps channel transmission.
On the front panel there is a “PH” button, press on the “PH” button on the remote site it
will sound.
To answer it the remote site just need to press the “PH” button on the remote unit, the
alarm will cut off and just plug in the phone both side able to do the communication.
Setting of the manage phone.
•It does not occupy the 2M circuits
pin definition description
1 MIC- MIC input -
2 SPEAKER+ Loudhailer output +
3 SPEAKER- Loudhailer output -
4 MIC+ MIC input +
1234

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 7 of 16
2.1.4 Front panel DIP definition
On the front panel of standalone / card in rack, the SW5 DIP definition shows as follows:
When MSK button pushes up, (RLOOP1-16): 1-16 E1 remote loop. If the RLOOP1 is
ON, this means that at the far end it is doing a E1 loop-back
0 means ON,1 means OFF
The corresponding E1
of remote Loop MSK button Bit1 Bit2 Bit3 Bit4 Bit5
1 push up 0 0 0 0 1
2 push up 0 0 0 1 0
3 push up 0 0 0 1 1
4 push up 0 0 1 0 0
5 push up 0 0 1 0 1
6 push up 0 0 1 1 0
7 push up 0 0 1 1 1
8 push up 0 1 0 0 0
9 push up 0 1 0 0 1
10 push up 0 1 0 1 0
11 push up 0 1 0 1 1
12 push up 0 1 1 0 0
13 push up 0 1 1 0 1
14 push up 0 1 1 1 0
15 push up 0 1 1 1 1
16 push up 1 0 0 0 0
All 16E1 Loop push up 0 0 0 0 0
E1 not Loop push up other units
Table 1
When MSK button push down, Bit1-5(mask1-5) mean 1-16E1 warning shielding.

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 8 of 16
1 means OFF, 0 means ON
Shielding E1 channel MSK button
contort Bit1 Bit2 Bit3 Bit4 Bit5
16 push down 0 0 0 0 1
15-16 push down 0 0 0 1 0
14-16 push down 0 0 0 1 1
13-16 push down 0 0 1 0 0
12-16 push down 0 0 1 0 1
11-16 push down 0 0 1 1 0
10-16 push down 0 0 1 1 1
9-16 push down 0 1 0 0 0
8-16 push down 0 1 0 0 1
7-16 push down 0 1 0 1 0
6-16 push down 0 1 0 1 1
5-16 push down 0 1 1 0 0
4-16 push down 0 1 1 0 1
3-16 push down 0 1 1 1 0
2-16 push down 0 1 1 1 1
1-16 push down 1 0 0 0 0
E1 not shielding push down Other units
Bit 6 : reserved.
Bit-7: ON: fiber interface local loop OFF: Cancel the loop
Bit-8: ON: The Ethernet interfaces are logically separated.
OFF: The Ethernet interfaces are exchangeable.

SNR-MPX-16E1-SFP
16E1 + 1Ethernet Fiber Optical Multiplexer
6/5/2009 Shop.Nag.Ru Page 9 of 16
2.2 Rear panel
Sketch map of rear panel for 120Ω
2.2.1 Power Supply
Support AC220V and DC-48V
•AC220V: 180-260VAC, directly insert power wire;
•-48VDC: the positive and negative of DC-48V can be optional because there is the
self-test circuit for the polarity inside the device
2.2.2 Ethernet (optional component)
This model can offer 1-4 channels for 10/100M, full/duplex auto-negotiation LAN
interface, support VLAN protocol, this interface can continuous learn MAC addresses in
the LAN that connected with it, and send the address as frame in another LAN.
Transparence to TCP/IP protocol, offers security connection between different equipments
in the network, used widely in network connection and monitor between WAN and LAN.
•10/100 Base-T Ethernet port parameter
•Rate: 10M or 100M, full/semi duplex self adaption.
•Ethernet rate in optical line: 100Mbps.
•Protocol: support IEEE 802.3, IEEE 802.1Q(VLAN)
•MAC address table: can learn 4096 MAC address
•Ethernet buffer memory: 64 Mbits SDRAM
•Physical interface: RJ45 slot, support AUTO-MDIX