NameLessRC D400 VTX+DVR AIO User manual

NameLessRC D400 VTX+DVR AIO
NameLessRC D400 VTX+DVR AIO
User Manual
Specification：
-Brand Name: NameLessRC
-Item Name: D400 VTX+DVR AIO
-Input Power: 5V
-Output Power: PIT/25mW/100mW/200mW/400mW Switchable
-Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362-5945 MHZ
-Control Mode: BFOSD Control/ Button, IRC Tramp ready
-Video Output format: NTSC
-Record video size : 1280x720 @30FPS
-TF Card support: Max.32G
-Compress Format: AVI
-Microphone: Yes
-Antenna: IPEX
-Mounting hole: 26.5*26.5mm
-Weight: 3.5g without antenna

NameLessRC D400 VTX+DVR AIO
Features:
-VTX maximum power up to 400mW.
-Built-in microphone.
-Support to choose recording FC OSD info or not.
-Start/Stop recording via button or OSD. Automatic recording after power on.
-Automatically save a video every 5 minutes.
-Cable plug and welding pads are both available.
-Small & light size for whoop and toothpick style frames.
-The VTX will not be damaged even if the antenna is dropped.
Attention:
-VTX's default set up is on lock mode(5733-5866MHZ unlock). Please
follow your local laws and regulations if you need to unlock the frequency.
-Please format the TF card to FAT/FAT32.

NameLessRC D400 VTX+DVR AIO
Pins Assignment：

NameLessRC D400 VTX+DVR AIO
Note:
You can choose to use the included cables or welding pads according to
your needs.

NameLessRC D400 VTX+DVR AIO
Precautions for use：
-Please maintain a good cooling environment for better performance.
-Input voltage must be within the specified range 5V.
-Please choose antenna with good VSWR and DB if you replace, to get far
transmission distance.
-Please use good TF card for better recording quality.
-Pay attention to static electricity protection during transportation and
installation.
Control methods：
VTX lock/unlock
(D400 VTXcable for Betaflight 4.1:
https://drive.google.com/open?id=1LR2UCBB_0OrupfQlvufxuH7ozPHD-1YI)
-The VTX is set up via BFOSD Control (IRC Tramp) or button.
-The VTX’s default set up is lock on 25mw.
-To lock/unlock the VTX :
Option 1: Long press the VTX button for 25 seconds after power on.The 3 LEDs
will flash one by one if the VTX is successful to unlock. Please re-power the VTX
after this step.
Option 2: Please enter the PIT mode for three times within 30secs after
powering up the VTX (PIT mode switch is set in BF mode page). The 3 LEDs will
flash one by one if the VTX is successful to unlock. Please re-power the VTX
after this step.

NameLessRC D400 VTX+DVR AIO
VTX LED functions：
-Orange LED shows channels status. Green for bands and Blue for power.
-The Green LED flash after Orange and blue LED flash at the same time means
the VTX enter PIT mode successfully.
-The three LEDs will flash one by one after the VTX is powered. After that, each
LED will flash to show the channel, band & power’s status. Orange LED flash 1
time for Channel 1, 2 times for Channel 2. Green LED flash 1 time for Band 1, 2
times for Band 2 and so on. The three LEDs will flash one by one again after
finish showing the status.
VTX Channel/Band/Power set up：
-Power the D400 and long press VTX button for 3 seconds. The Channel Orange
LED will flash. 1 time for Channel 1, 2 times for Channel 2 and so on. Short press
to switch the Channel.
-Long press VTX button for 3 seconds after step 1, the Band Green LED will flash.
1 time for Band 1, 2 times for Band 2 and so on. Short press to switch the Band.-
-Long press VTX button for 3 seconds after step 2, the Power Blue LED will flash.
1 time for 25mW, 2 times for 100mW and so on. Short press to switch the
Power.
-Long press VTX button for 3 seconds after step 3 or re-power the D400, the set
up will be saved.（Re-power during each step also can save the set up)

NameLessRC D400 VTX+DVR AIO
Frequency Table(Mhz):
Red area on frequency table is locked area! Please follow your local laws and regulations .
DVR Recording:
-DVR White LED constantly bright means it is in standby, flashing means
recording.
Option 1: Automatic recording after power on.
Option 2: Short press the DVR button to start/stop recording.
Option 3: Start/stop recording via OSD control (Video: https://youtu.be/v9MAinKmdsQ)
-Enter the OSD VTX set up page
Channel
1
2
3
4
5
6
7
8
Band A
5865
5845
5825
5805
5785
5765
5745
5725
Band B
5733
5752
5771
5790
5809
5828
5847
5866
Band E
5705
5685
5665
5645
5885
5905
5925
5945
FS
5740
5760
5780
5800
5820
5840
5860
5880
Race Band
5658
5695
5732
5769
5806
5843
5880
5917
Low Race
5362
5399
5436
5473
5510
5547
5584
5621

NameLessRC D400 VTX+DVR AIO
-Switch the POWER to ON and confirm. The code will show 513 which means
the DVR is starting to recording. Meanwhile, the DVR White LED will be flashing.

NameLessRC D400 VTX+DVR AIO
-Switch the POWER to OFF and confirm. The code will show 515 which means
the DVR stop recording. Meanwhile, the DVR White LED will be constantly
bright.
Note: We recommend setting the power you expect again after start/stop
recording via OSD.