Namron ZigBee User manual

NAMRON DIY ZigBee RGBW LED Controller09.ZGDIYRGBW.04282Function introductionImportant: Read All Instructions Prior to Installation12VDC InputCommon Anode output (+)• DO NOT install with power applied to device. • DO NOT expose the device to moisture. Product DataSafety & WarningsInput VoltageOutput TypeOutput Current12/24VDCConstant voltage72W@12V, 144W@24V4CH, 1.5A/CHOutput PowerNo.1Dimension (LxWxH)84x20x14mmCH 3 (B) output (-)CH 2 (G) output (-)CH 1 (R) output (-)CH 4 (W) output (-)• Mini size zigbee RGBW LED light device based on latest ZigBee 3.0 protocol• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights• ZigBee end device that supports Touchlink commissioning• Supports find and bind mode to bind a ZigBee remote• Compatible with universal ZigBee gateway products• Waterproof grade: IP20• W channel can be controlled through Gateway’s color temperature control interface• W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button• Supports self-forming zigbee network without coordinator• Supports zigbee green power and can bind max. 20 zigbee green power remotesOperation1.Do wiring according to connection diagram correctly.2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)4. TouchLink to a Zigbee Remote< 10cmNote: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. 4) After TouchLink, the device can be controlled by the linked remotes.V+ V+R- R-G- G-W- W-B- B-ZigbeeRemoteStep 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually".Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 minutes timeout, repeat the operation.Step 1: Method 1: Re-power on the device 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation. Method 2: Re-power on the device, Touchlink commissioning will start after 15 if it’s not added to a zigbee network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout, repeat the operation.minutesStep 2: Bring the remote or touch panel within 10cm of the lighting device.Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to corresponding remote or touch panel manual to learn how.Step 4: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller's menu and can be controlled through controller or hub interface.Step 4: There shall be indication on the remote for successful link and connected light will flash twice. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset.AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-Input Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-V+ V+R- R-G- G-W- W-B- B-
Note: 1) W channel can be turned on through Gateway’s color temperature control interface which will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels. 2) W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button, please refer to their manuals.

6. Factory Reset ManuallyNote: 1) If the device is already at factory default setting, there is no indication when factory reset again . 2) All configuration parameters will be reset after the device is reset or removed from the network.Step 1: Re-power on the device for 5 times continuously. 8. Find and Bind ModeStep 1: Re-power on the device (initiator node) 3 times to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it to find and bind initiator, please refer to corresponding remote or touch panel manual.Step 3: There shall be indication on the remote or touch panel that it bind the device successfully and can control it then.ZigbeeRemoteStep 4: There shall be indication on the remote and connected light flashes 3 times for successful reset. Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.7. Factory Reset through a Zigbee Remote (Touch Reset)Note: Make sure the device already added to a network, the remote added to the same one or not added to any network. Step 2: Bring the remote or touch panel within 10cm of the lighting device.Step 3: Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to corresponding remote or touch panel manual to learn how.ZigbeeRemoteStep 2: Connected light will blink 3 times to indicate successful reset.9. Learning to a Zigbee Green Power RemoteStep 2: Set the green power remote into Learning mode, please refer to its manual.ZigbeeGreen PowerRemoteStep 3: Connected light will flash twice to indicate successful learning. Then the remote can control the device.Step 1: Re-power on the device 4 times to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation.Note: Each device can learn to max. 20 zigbee green power remotes.10. Delete Learning to a Zigbee Green Power RemoteStep 2: Set the paired green power remote into Learning mode, please refer to its manual.ZigbeeGreen PowerRemoteStep 3: Connected light will flash 4 times to indicate successful deleting. Step 1: Re-power on the device 3 times to start delete Learning mode (connected light flashes slowly), 180 seconds timeout, repeat the operation.11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)ZigbeeRemote< 10cmTouchLinkStep 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals.Step 1: Re-power on the device 4 times to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation.< 10cmZigbee Lighting DeviceAC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W- AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-AC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-
V+ V+R- R-G- G-W- W-B- B-V+ V+R- R-G- G-W- W-B- B-V+ V+R- R-G- G-W- W-B- B- V+ V+R- R-G- G-W- W-B- B-V+ V+R- R-G- G-W- W-B- B-V+ V+R- R-G- G-W- W-B- B-

Input Clusters• 0x0000: Basic• 0x0003: Identify• 0x0004: Groups• 0x0005: Scenes• 0x0006: On/off• 0x0008: Level Control• 0x0300: Color Control• 0x0b05: DiagnosticsOutput Clusters• 0x0019: OTA12. ZigBee Clusters the device supports are as follows:13. OTAWiring DiagramThe device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically. Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.Note: 1) Each added device can link and be controlled by max. 30 added remotes. 2) Each added remote can link and control max. 30 added devices.Product DimensionAC Power50/60HzLNGV+V-
OUTPUT
INPUT
12/24VCV PSUInput Voltage:DC 12-24VOutput Current:4x1.5A max.Max Output Power:72-144WZigBee RGBW LED ControllerDC INPUTRed:V+Black:V-LED OUTPUTBlack:LED+Red:R-Green:G-Blue:B-White:W-V+ V+R- R-G- G-W- W-B- B-87 mm
34 mm15 mm
Importer:Namron ASNedre kalbakkvei 88B1081 OlsoNorwayMade in China