Napoleon CSS610RB Manual

BUILT-IN CSS610RB INSTRUCTION GUIDE
N415-0147/JAN12/06
Please use this manual in conjuction with your main manual to properly assemble your built-in grill. Refer to the
main manual for operating, cleaning, and maintenance instructions. This grill is designed for masonry, non-
combustible enclosures only, and must be installed and serviced by a qualified installer to local codes.
BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane installation code in
Canada, or to the National Fuel Gas code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 1/2" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN
B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The gas
supply must be connected to the 3/8” flare fitting located under the left hand side of the control panel. If the enclosure is to house a
propane cylinder, the tank portion of the enclosure must be ventilated according to local codes, and must not have communication
with the cavity used to enclose the gas grill. The tank can not be stored below the gas grill.
BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be located as
shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe, copper tube or an
approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane Installation Code in
Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended piping size is NPS 1/2"
for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes to conform with CAN
B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States.
Built in units are supplied with a drip pan which holds only a minimal amount of grease. To prevent grease fires, the pan must
be cleaned after each use. Access must be provided to the inside of the enclosure to make gas connections.
SERIAL #______________________
9¾”
20 ¼”
2”
32”
6”MIN
34”
RECOMMENDED
2½”
GASINLET
OPENING

H
W
D
NOTE:ACCESSORY FRAMES OVERLAP
OPENINGBY1½”ONALL4SIDES
Part # Description Picture WH
N370-0070 Flat horizontal painted door
N370-0357SS
N370-0358SS
13¼” 18¼”
OPENINGDIMENSION
N370-0356SS Curved stainless steel door - 308 size
N370-0072 Flat horizontal stainless steel door
N370-0069 Flat vertical painted door
N370-0071 Flat vertical stainless steel door
Curved stainless steel door - 450 size
Curved stainless steel double door - 600 size
N370-0361 PF style stainless steel door
N370-0359 PF style stainless steel single drawer
N370-0360 PF style stainless steel triple drawer
13¼” 18¼”
18¼” 13¼”
18¼” 13¼”
22½” 19¾”
27” 19 ¾”
17” 23¼”
17¼” 6¾”
17¼” 22¾”
BUILT-INACCESSORY OPENING DIMENSIONS
35¼” 19”
23”
23”
D

1. Lower the unit into the opening. Feed the gas flex connector and regulator down through the opening on the left hand
side (natural gas only).
2. For natural gas units, mount the regulator to the cabinet. Connect the gas supply to the inlet side of the regulator. For
propane units, connect the gas supply to the 3/8” flare fitting located on the left side of the manifold tube.
3. Leak test the entire installation before operating the unit.
GASINLET
OPENING

BUILT-IN ACCESSORY DRAWER INSTRUCTIONS
BUILT-IN ACCESSORY DOOR INSTRUCTIONS
1.Unpackthedrawerframe assembly.
2.Remove thedrawers from the enclosure by fully extending them andthen liftingup to remove them from the slides.
3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at
the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure
that the front of the enclosure is plumb.
4. Once the enclosure is level and square, fasten into place. (Fasteners not included).
5. Re-install the drawers by tipping the back of the drawer down into the slide. Once the wheels are inserted into the slide,
lower the front of the drawer until it is level, then push in. Note: if the enclosure is installed with shims that are too thick, the
wheel will not engage into the slide. The shim thickness will need to be reduced.
6.Remove the protectivecoating from allremaining surfaces.
1. Unpack the door and frame.
a. For the curved stainless steel doors, remove the door(s) from the frame by lifting the door while holding on to the pivot
rod. This will allow the pivot rod to come out of the hole on the bottom of the frame. Once the pivot is removed from the
bottomhole, the entire door can be droppedand removed from the frame.
b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on the hinge
furthest away from the door. This will allow the hinge to separate.
2. Center the frame in the opening. Mark the location of the pivot holes, top and bottom. Remember on the PT600 double
doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once all pivot holes are marked,
remove the frame and using a 3/8” drill bit, drill out the clearance holes for the pivot rod. These clearance holes should be
at least 1/2” deep. After the holes are complete, you may once again center the frame in the opening. Starting with the
hinged side, shim between the frame and side wall of the opening. Ensure the shims are close to the hinge on the PF style
doors. When the frame side wall is plumb, fasten it to the cabinet with screws (not provided). Attach the other side of the
frame in the same fashion, ensuring the frame is square.
3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and bottom of the frame.
The curved stainless steel double door frame must be fastened in the center both at the top and bottom.
4. Once the frame has been secured and checked for squareness, the door can be re-installed.
5.Remove theprotective coating from all remaining surfaces.