Nat 802-009 Owner's manual

802-006 Switch Panel
SM802 Installation and Operation Manual Supplement
SM Supplement Rev: 1.30 Jun 28, 2010 Page i
ENG-FORM: 810-0112.DOT
CONFIDENTIAL AND PROPRIETARY TO NORTHERN AIRBORNE TECHNOLOGY LTD.
Prepared By: Checked By: Certification: Approved By:
Revisions
Rev. CR No. Date Description of Change
1.30 ECO10456 Jun 28. 2010 Added latest drawing.
1.21 DOCCR02692 Nov 18, 2008 Corrected Switch Panel part number.
1.20 MANCR02414 Jun 13, 2008 Revised Outline drawing. Added briefer volume statement
to Section 1 Description.
1.10 DOCCR00772 Jan 6, 2006 Revised Outline drawing.

802-006 Switch Panel
SM802 Installation and Operation Manual Supplement
SM Supplement Rev: 1.30 Jun 28, 2010 Page 1
This supplement contains installation and operation information that is unique to the 802-006 Switch
Panel. Installation and operation information common to the 802 base unit can be found in the SM802
Installation and Operation Manual.
Note: The information in this manual supplement was previously contained in Equipment Manual:
Component Maintenance Data, document number 802-16-006.
Section 1 Description
The 802-006 is identical to the 802-009 with the following exceptions:
a) Changes to the faceplate can be found by comparing Figure 1 to Figure 2.
Figure 1: 802-009 Figure 2: 802-006
b) The PA Volume control has been replaced by the CALL (momentary) switch.
c) The front panel TCN switch/volume potentiometer controls the ON/OFF switching and
volume of two internal multiplexer circuits labelled ADF2 and MKR2 on the 802-009
drawing.
d) The Push-To-Talk switch has been added to the 802-006 front panel in addition to the
original rear panel connection at P1.
e) The BRIEFER volume adjustment is not installed.
ENG-FORM: 810-0112.DOT
CONFIDENTIAL AND PROPRIETARY TO NORTHERN AIRBORNE TECHNOLOGY LTD.

802-006 Switch Panel
SM802 Installation and Operation Manual Supplement
Page 2 Jun 28, 2010 SM Supplement Rev: 1.30
ENG-FORM: 810-0112.DOT
CONFIDENTIAL AND PROPRIETARY TO NORTHERN AIRBORNE TECHNOLOGY LTD.
Section 2 Installation
For installation information and drawings, see SM802 Section 2. Select the appropriate revision of the
drawing for the serial number of the unit. The drawings specific to this derivative are listed below and can
be found at the end of this supplement.
2.1 Numerical Pin Identification List
The connections to the 802-006 are similar to the connections to the 802-009 with the following
exceptions:
Pin 802-009 Name 802-006 Name
1 N/C CALL SWITCH
6 HF-1 ANTENNA SWITCHING N/C
7 PA/Briefer Interconnect N/C
8 PA/Briefer Interconnect N/C
14 PA VOLUME N/C
16 HF-2 ANTENNA SWITCHING N/C
27 HF-1 KEY VHF-3 KEY
30 N/C PA SDTN SWITCH
31 MKR HI control N/C
32 HF-1 & 2 ANTENNA SWITCHING N/C
38 XCVR-5 MIC UHF MIC
39 HF-2 MIC HF MIC
40 PAMIC N/C
41 HF-1 MIC VHF-3 MIC
44 N/C UHF KEY
45 HF-2 KEY HF KEY
46 PA KEY N/C
50 NORM discrete output N/C
2.2 Installation Drawings
DOCUMENT REV. DESCRIPTION TYPE
802-006
802\006\802-006 1.30 Product Nomenclature Outline
Section 3 Operation
For operation information, see SM802 Section 3.
The CALL switch is a momentary type (normally out, OFF). The CALL switch provides 28 VDC at a single
rear P1 connector pin while depressed. This is used for activation of the Model 240 or 205 chime signal
(see pin identification list).
To key a selected transmitter, the pilot may either use the typically yoke mounted Push-To-Talk (PTT) key
switch or the front panel mounted PTT switch with the NORM or OXY microphones, or the PTT key switch
on the hand held microphone when using it.
Supplement ends

This page intentionally left blank