National Public Seating 42-8 Table/Chair Storage Truck User manual
Model # 42-8 Table/Chair Storage Truck
Assembly Instrucons
The Naonal Public Seang 42-8 Table/Chair Storage Truck has been upgraded and is now even more funconal than before —
with your safety in mind. Now stores up to 42 Folding Chairs and 12 Folding Tables with included bungee cords for stability and
safety when your unit is fully loaded.
If you experience any problems with this product,
please call our customer service department at 800-261-4112
ASSEMBLY TIPS : All assembly should be done on a
clean protected surface, such as carpet or the like.
Assembly is easy and should take no more than 10
minutes.
ASSEMBLING THE UNIT : (See other side of sheet for
assembling unit with Oponal EXT-8 extender bars )
STEP 1) Make sure that there are NO missing or dam-
aged parts.
STEP 2) While holding up one of the side “T” bars (Part
A), bolt one crossbeam (Part C) into the middle set of
holes. NOTE: This set of holes has three holes. Use
either the two lower or two higher ones for installa-
on.
STEP 3) Take the other side “T” bar (Part A), and bolt it
to crossbeam (Part C) in the middle set of holes. NOTE:
This set of holes has three holes. Use either the two
lower or two higher ones for installaon.
STEP 4) Take the chair rack (Part B) and bolt it to the
top sets of holes on both side “T” bars (Parts A).
STEP 5) Finally, bolt crossbeam (Part C), into the
boom sets of holes on both side “T” bars (Parts A).
STEP 6) Ascertain that each and every nut and bolt is
securely ghtened to its maximum!
STEP 7) Load up to 42 folding chairs on chair rack. Then load up
to six tables on each side of the boom of unit. Once loaded,
secure tables using both of the provided bungee cords. Start by
inserng one end of the cord into holes located on steel table
holders (Part D) at boom of unit then pulling around over ta-
bles and inserng second end of cord into holes on the corre-
sponding steel table holders.
OPTIONAL STEP 8) Aach oponal coat rods to the chair hanging
rods (on parts B), use as coat rack when chairs are out.
ASSEMBLY :
STEP 1) Ascertain that there are NO missing or dam-
aged parts.
STEP 2) While holding up one side of the “T” side-bar
(Part A), bolt crossbeam (Part C) into the middle set of
holes. NOTE: This set of holes has three holes. Use ei-
ther the two lower or two higher ones for installaon.
STEP 3) Take the other side “T’ bar (Part A), and bolt it
to crossbeam (Part C) in the middle set of holes.
STEP 4) Take one EXT-8 bar (Part E) and place the wid-
er part over the top of the “T” bar (Part A). Align the
two holes of the EXT-8 bar with the holes of the “T”
bar and bolt them in.
STEP 5) Take the other EXT-8 bar (Part E) and do the
same to the other “T” bar.
STEP 6) Take the Chair rack (Part B), and bolt it to the
set of holes on top of the EXT-8 bar.
STEP 7) Finally, bolt other crossbeam (Part C), into the
boom sets of holes on both “T” side-bars (Parts A).
STEP 8) Ascertain that each and every nut and bolt is
securely ghtened to its maximum!
STEP 9) Load up folding chairs on chair rack. Then load
up to six tables on each side of the boom of unit. Once loaded,
secure tables using both of the provided bungee cords. Start by
inserng one end of the cord into holes located on steel table
holders (Part D) at boom of unit then pulling around over ta-
bles and inserng second end of cord into holes on the corre-
sponding steel table holders.
OPTIONAL STEP 8) Aach oponal coat rods to the chair hang-
ing rods (on parts B), use as coat rack when chairs are out.
* The EXT-8 Extender bar should be used to accommodate the
following NPS chairs: 3200 series, 1100 series and 600 series
Model # 42-8 Table/Chair Storage Truck
Assembling unit with Oponal EXT-8 Extender
bar*
If you experience any problems with this product,
please call our customer service department at 800-261-4112
Table of contents
