National Tree Company JI60-JFMT03 User manual

CAUTION: IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors unless
marked suitable for indoor and outdoor use.
When products are used in outdoor applications,
connect the product to a Ground Fault Circuit
Interrupter (GFCI) outlet. If one is not provided,
contact a qualified electrician for proper installation.
• This seasonal use product is not intended for
permanent installation or use.
• Do not mount or place near gas or electric
heaters, fireplaces, candles or other similar
sources of heat.
• Do not secure the wiring of the product with
staples or nails, or place on sharp hooks or nails.
• Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
• Do not let lamps rest on the supply cord or any wire.
•CAUTION: This is an electrical product – not a toy!
To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or
placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from
cord, wire or light string.
• Do not close doors or windows on the product or
extension cords as this may damage the wire
insulation.
• Never operate this product if the power cord or
plug is damaged.
• Read and follow all instructions that are on the
product or provided with the product.
USE AND CARE INSTRUCTIONS
• When storing the product, carefully remove the
product from wherever it is placed, avoiding any
undue strain or stress on the product conductors,
connections, and wires.
• When not in use, store neatly in a cool, dry
location protected from sunlight.
ASSEMBLY INSTRUCTIONS
Figure 1
Product includes: top and bottom tree sections, tree trunk, folding
metal stand with 3 thumb screws, 12 pcs. hardware, remote control
and hanging skull (Figure 1).
Assembly
1. Locate the tree trunk mounting plate on the bottom section of the
tree. Insert the two silver bolts through the holes in the plate on
the tree (Figure 2). Insert the bolts through the holes of the tree
trunk plate and secure together using the nuts supplied. Note
correct installation as shown in Figure 3.
2. Attach the tree top section to the tree bottom section by aligning
the plates on each section and securing together using the four
black bolts and four nuts (Figure 4).
3. Unfold tree stand and insert tree trunk pole into stand. Insert
thumb screws into stand and tighten to secure tree in stand.
4. Connect the light string from the top section into the light string of
the bottom section (Figure 5). Plug light string into power supply.
Hanging Skull
Hang the skull at the tip of the tree as shown in Figure 6. The skull
lights are battery operated (battery included). The ON/OFF switch is
at the base of the skull.
TOP
BOTTOM
Position of tree trunk
when properly installed
Figure 2
Figure 4
Figure 3
Figure 4
Figure 5
Figure 6
continuedonreverse side

2 Commerce Drive, Cranford, NJ 07016 www.nationaltree.com Item No. JI60-JFMT03
Made in China Printed in China
SAVE THESE INSTRUCTIONS
Light Operation
Light functions are operated by using the remote control
(Figure 7). Functions are as follows:
ON = Activates lights
OFF = Turns lights off
TIMER = Press the button to activate the 6 hours ON/18
hours OFF timed operation. Timer will continue this cycle
until button is pressed again to deactivate.
Light MODE 1 = Combination
Light MODE 2 = Wave
Light MODE 3 = Sequential
Light MODE 4 = Slow Glow
Light MODE 5 = Chasing/Flash
Light MODE 6 = Slow Fade
Light MODE 7 = Twinkle/Flash
Light MODE 8 = Steady On
DIM – = Reduce Brightness
+ = Increase Brightness
Storage
Carefully disassemble in reverse order of assembly. All parts can be
replaced in carton and should be stored in a cool, dry place.
Figure 7