naturaled SEN-HB001VCR-1 User manual

Daylight
threshold
Stand-by
period
Stand-by
dimming level
Hold
time
Detection
area
On/o
control
Remote control
setting
5
years
Mechanical structure (Unit: mm)
Well covered Covered
Antenna module
Installation hole
Detection Range
Hold Time
Stand-by Dimming level
Stand-by Period
Daylight threshold
Daylight sensor
Typical installation height 2.5-4m
This gure indicates the maximum distance at the highest mounting height with 100% sensitivity.
Detection coverage
Technical data
Detection area
DIM 1-10V Dimming
10%/20%/30%/50%
Max, ø10m (ceiling mounted)
Operating voltage
Output
<30mAStand-by power
Hold time
Daylight threshold
Stand-by period
Stand-by dimming level
5.8GHz±75MHz
<0.3mW
Microwave frequency
Microwave power
Mounting height
Detection range
30°-150°
Operating temperature
IP rating
10-15VDC
IP20
Detection angle
-20°C~+60°C
Warranty 5 years
10Lux/30Lux/50Lux/Disable
50%/100%
10s/1min/5min/10min
P10438
SEN-HB001VCR-1
DC input , Rod antenna
1. Automatic On/o control with
Daylight sensor.
2. DC input
3. Remote control.
IR Receiver
Ceiling Mounted
1 2 3 41234
1
2
3
4
Mounting
height
01
85
22.3
11.3
6.2
11.3 Ø2.5
Ø2.5
2.5
Ø5.5
13.86
12.8
1.8
7.8
11.7
0
P10323 SEN-HD05R

Installation Method
Applications
Settings
Stand-by
dimming level
100%
50%
10s
1min
5min
10min
Disable
50lux
30lux
10lux
1min
60min
30min

10%
30%
20%
50%
Switch UP
Switch DOWN
The period of light
keeping low
output before it's
completely
switched off.
When it's preset
DV´WKHOLJKW
always keep at low
output if no
movement in the
detection area and
doesn't turn off.
The definition
of low output
in the standby
period.
In this area,
movement will
be detected and
able to trigger
the sensor.
100% detection
area is also
known as the
strong
sensitvity.
The period of
light keeping
100%
brightness after
moving objects
leave the
detection area.
Definition of the
ambient brightness;
only when the
ambient brightness
is lower than the
preset specific lux
amount, the sensor
will work; when it's
preset as "disable",
the sensor works
everytime it detects
motion regardless
the ambient
brightness.
Detection area Hold-time Daylight threshold Stand-by period
Wiring diagram
Note: Motion sensor setting and dimming setting please refer to remote control HD03R.
02
LED D
Yellow：12V
Grey ：GND
purple：DIM+
river

Attention
03
Application
With insufficient
daylight, when motion
detected, light ON.
With sufficient daylight,
even when motion
detected, light remains
OFF.
After the stand-by
period, light OFF.
After last detection, the
light will be dimmed
down to the stand-by
dimming level
(10%,20%,30% or 50%)
after holdtime.
Hold time Stand-by period
3. Function Demo - Dimmable control/Corridor function
After people leave the detection
area, light remains 100%
brightness within hold time.
When motion is detected,
the sensor will switch on the
light to 100% brighteness.
After the last detection and
the present hold time
elapsed, light OFF.
1. Please read the instructions carefully before using this product and keep it well
for all users to read at any time.
2. The sensor should be installed by qualified electrician and ensure power is off
before the installation.
3. We reserve the right to modify any incorrect text, image and necessary technical
parameters.
$Q\XQDXWKRUL]HGPRGLILFDWLRQLVIRUELGGHQRWKHUZLVHDOOJXDUDQWHHVZLOOEH
immediately invalid.
1. Microwave sensor can be installed in any lamp except the one with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
7KHGHWHFWLRQVXUIDFHRIWKHVHQVRUPRGXOHVKDOOEHLQVWDOOHGIDFLQJWKHGHWHFWLRQDUHD
5. Should be kept away from the driver to avoid interference generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to avoid short circuit.
Installation precautions
1. Suitable for indoor installation to avoid false triggering due to external factors such as rain, wind or
tree swing.
2. Shall not be installed in the place with all four metal shelters and small space (such as
galvanized-iron roof ).
3. Shall note be mounted installation, so as to avoid false trigger caused by the lamp itself shaking.
6KDOOQRWEHLQVWDOOHGQH[WWRODUJHRSHUDWLQJPDFKLQHVVXFKDVYHQWLODWRUFHLOLQJIDQWRDYRLGIDOVH
triggering caused by machine vibration.
Application Environment
1.Microwave can penetrate walls or glass thinner than 20cm and attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting height and movement volume.
&RQGXFWWHVWRQVXQQ\GD\VZLWKRXWWKHODPSVKDGHZKLFKZLOODIIHFWWKHWHVWHGOX[YDOXH
User Notes
1. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off
after stand-by period .
Applications: Dim places such as Basement Parking, Underpass.