Nautilus NB 3000 User manual

Assembly Manual
NB 3000
EXERCISE BIKE

TOOLS AND HARDWARE
STEP 1: Attaching the Front Stabilizer
Attach the front stabilizer (#8) to the frame (#1), using two washers (#13), two spring
washers (#25) and two hex bolts (#12).
ASSEMBLY INSTRUCTIONS
NO. Description Quantity
11 Phillips Head Screw M5 (12mm) 2
12 Hex Bolt M8 (90mm) 4
13 Flat Washer 6
19 Allen Bolt M8 (16mm) 2
25 Spring Washer 6
27 Allen Bolt M8 (20mm) 2
37 Spring washer 4
86 Button Head Screw M8 (45mm) 2
7-5 Phillips Head Screw M5 (25mm) 2
7-4 Phillips Head Screw M5 (35mm) 2
7-6 Phillips Head Screw M5 (10mm) 4

NB 3000 EXERCISE BIKE ASSEMBLY INSTRUCTIONS
STEP 2: Attaching the Rear Stabilizer
Attach the rear stabilizer (#9) to the frame (#1), using two washers (#13), two
spring washers (#25) and two hex bolts (#12).
STEP 3: Assembling Handlebar & Console Mast
Attach the handlebar (#6) to the console mast (#2), using two washers (#13), two
spring washers (#25) and two button head screws (#86). Insert the handlebar boot
(#64) into the shrouds (#17, #18). Connect the upper computer wire (#21) with the
lower computer wire(#68). Secure the console mast using two Allen bolts (#19) and
two shroud caps (#20). Be careful not to damage computer wire during assembly.

NB 3000 EXERCISE BIKE ASSEMBLY INSTRUCTIONS
STEP 4: Attaching Computer Console
Plug the upper computer wire (#21) and the hand grip wire (#70) into the com-
puter console (#7-1). Fasten the computer console (#7-1) to the console mast (#2)
using four washers (#37) and four Phillips head screws (#7-6). Attach the computer
lower cover (#7-3) to the computer console (#7-1) using two 35mm Phillips head
screws (#7-4), and two 25mm Phillips head screws (#7-5).
STEP 5: Attaching Water Bottle Cage
Install the bottle bracket (#65) into the shroud using two Allen bolts (#27). Then
assemble the water bottle cage (#61) into the bracket using two Phillips head screws
(#11).

NB 3000 EXERCISE BIKE ASSEMBLY INSTRUCTIONS
STEP 6: Installing Seat
Secure the seat (#5) onto the seat post (#3) by tightening the hex nut below the
seat frame. Then loosen the pull knob (#14) and install the seat post into the frame
(#1). You will want to adjust seat (#5) to desired angle after you test for comfort.
STEP 7: Installing Pedals & Straps
Attach the pedals (#10-1[L] and #10-1[R]) to crank (#4) using supplied wrench. The
left pedal is left-handed thread, and must be tightened counter-clockwise. The
right pedal is right-handed thread, and must be tightened clockwise. After pedals
are installed, attach pedal straps to pedals at desired length.

NB 3000 EXERCISE BIKE
Final Check
Assembly of your Nautilus bike is now complete. Check again to insure that all parts
are properly installed and that all nuts and bolts are completely secured. Get on the
bike and check to see that the computer console and resistance system are working
properly.
Please be sure to read through your Nautilus owner’s manual completely before
using your bike. It will describe in detail how to operate the product safely and cor-
rectly.
Should you experience any problems or have any additional questions about your
Nautilus bike, please contact your Authorized Nautilus Fitness Retailer from where
your equipment was purchased.

The Nautilus Group
1886 Prairie Way
Louisville, Colorado 80027
1.888.471.0014
www.nautilus.com
Rev.C