Nav tv Ford 4" uni-cam kt2 Manual

FORD 4” UNI-CAM KT2

Dual Camera Integration kit for Ford 4” screens

NTV-KIT593

BHM

10/25/18

NTV-DOC257

3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

2 | P a g e

USB Cable

NTV-CAB009

Optional Reverse Cameras

F-Series/Flex CAM

Transit-CAM

included in

NTV-KIT623

CAM 6

RCA input cable

NTV-CAB071

Overview

The FORD 4” UNI-CAM KT2 kit interfaces an aftermarket rear (and optional front) camera into Ford vehicles equipped

with the OEM 4” media screen. No dealership programming is required and this kit if fully Plug & Play behind the factory

media screen. Note: before installing this module, VERIFY 75 ohms exists across pins 6 & 12 with a multimeter at the

4” screen connector.

Kit Contents

Ford 4” UNI-CAM pin out

PIN #

Description

Color

12v (+) constant input

Yellow

Input 1: Force RVC

Red

Input 2: Force FVC/AUX VID

Blue

Input 3: --Not Used--

Pink

VIDEO OUT RCA

Orange/White

RCA Shield

Orange

CAN HI (Radio Side)

White/Blue

CAN HI (Car Side)

Brown/Black

Ground (-)

Black

Output 1: ACC (+)

White/Red

Output 2: Reverse (+)

White/Blue

Output 3: Front CAM power

White/Purple

Front RCA Video IN

White

Rear RCA Video IN

Yellow

CAN LO (Radio Side)

Blue

CAN LO (Car Side)

Brown

KT2 UNI-CAM Module

NTV-ASY245

Plug & Play T-Harness

NTV-HAR271

Wire side

Any additional wires not mentioned here are

not used for this install.

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

3 | P a g e

Module Installation

1. Remove the 4” media screen from the dashboard, above the CD player.

2. Connect the provided Plug & Play T-Harness to the OEM ford 12-pin plug previously

connected to the radio.

3. After installing and running your reverse camera to the dash opening, connect your RVC signal to

the Yellow RCA found on the Plug & Play T-Harness. Power your camera with an ACC source

(OUTPUT 1 provides 12v ACC @ 1 amp MAX).

4. Connect the UNI-CAM module to the 18-pin harness on the Plug & Play T-Harness.

5. Connect the male end of the Plug & Play T-Harness to the screen and proceed to the next

section.

Ford 4” UNI-CAM Programming & Testing

Programming for the 4” UNI-CAM is automatic. After all connections are properly made and the module is

connected, turn the car on to IGNITION, wait for the radio to fully boot and settle before testing functionality.

NOTES:

•The radio may or may not visually reboot with a ‘Diagnosis’ message. It may appear that the radio

just boots slowly (only the first time, in which case it took programming before the display

appeared).

•Place the car into reverse, the screen should automatically display the connected reverse image.

NOTE: you must have a camera powered and connected (for Ford systems)!

•This module VIN-LOCKS to the vehicle it is connected to and cannot be used on any other vehicle

once installed.

•This module will NOT de-program rear camera, once this modification is made to the system, it will

remain forever!

LED Response

Description

1 flash

Waiting for Ignition… (Turn ignition to ON)

2 flashes

Waiting for Vehicle VIN…

3 flashes

Query Vehicle (Reading/decoding the VIN and vehicle components)

4 flashes

Programming…

5 flashes

Programming Complete

6 flashes

No Programming Needed (Already programmed)

7 flashes

Radio Not Supported

8 flashes

Out of Licenses (Contact NAV-TV to purchase more licenses)

While programming, refer to the chart below for LED flash representation.

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

4 | P a g e

•After all connections are made and programming is complete, placing the vehicle in reverse will

automatically display the connected rear camera’s image.

•If forced rear camera is desired, connect input 1 (red) to 12v (+) through a toggle (not included)

and the rear image will show whenever activated.

•If a front camera was added, force this camera by connecting input 2 (blue) to 12v (+) through a

toggle (not included).

Ford 4” UNI-CAM Operation

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

5 | P a g e

NOTES:

•Any wires not shown here are not needed for this installation.

•Not all wires shown here will be used for every installation.

The reverse image will have rounded edges and the OEM radio

screen showing behind the reverse image is OEM Ford

operation and is normal.

Some vehicles may retain the reverse image while in drive until

~5 mph, this is also normal Ford operation.

FORD

UNI-CAM

KT2

Installation Diagram

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

6 | P a g e

Find the PART

number on the

back of the

main 4” media

screen.

Verify 75ohms

on pins 6 & 12

on the back of

the main 4”

media screen.

Ford 4” Screen Compatibility list

Due to the large variety of different 4” screen part numbers, it is strongly advised to verify the screen

compatibility by removing the screen and measuring a 75 ohm termination across pins 6 and 12. NAV-TV

cannot assure compatibility unless this step has been taken.

Incompatible Display PART #’s

EM5T-18B955-CB

CM5T-18B99-AD

CJ5T-18B955-GF

EM5T-18B955-CA

CM5T-18B955-GF

CJ5T-18B955-GE

EJ5T-18B955-GB

CM5T-18B955-CE

CJ5T-18B955-GC

DM5T-18B955-CD

CM5T-18B955-AD

CE8T-18B955-AD

DA6T-18B955-BE

CM5T-18B955-AB

CE8T-18B955-AA

D2BT-18B955-BE

BB5T-19C116-CJ

Compatible Display PART #’s

FG1T-18B955-CA

EJ5T-18B955-GA

DT4T-19C116-GB

DL3T-18B955-CC

CM5T-18B955-GB

FB5T-19C116-GA

EJ5T-18B955-CC

DT4T-19C116-CD

DG1T-18B955-CD

CM5T-18B955-CF

FB5T-19C116-CA

EG1T-18B955-CD

DT4T-19C116-CC

DB5T-19C116-GB

CK4T- 18B955-CD

ET4T-19C116-GG

EG1T-18B955-CA

DT4T-19C116-CB

DB5T-19C116-GA

CK4T-18B955-CF

ET4T-18B955-CC

EB5T-19C116-CD

DT4T-19C116-CA

DB5T-19C116-CBT

CB5T-19C116-GD

ES7T-18B955-CB

EB5T-19C116-CA

DS7T-18B955-CF

DB5T-19C116-CA

CB5T-19C116-GC

ES7T-18B955-CA

EB5T-18B955-GC

DS7T-18B955-CE

DA8T-18B955-CF

CB5T-19C116-CD

EM5T-18B955-JB

EB5T-18B955-GA

DL3T-18B955-CG

DA8T-18B955-CD

CB5T-19C116-CC

EM5T-18B955-CE

EA8T-18B955-CB

DL3T-18B955-CF

CM5T-18B99-GG

BT4T-19C116-CP

EL3T-18B955-CE

DT4T-19C116-GD

DL3T-18B955-CD

CM5T-18B955-GE

BB5T-19C116-CK

CM5T-18B955-GD

BT4T-19C116-CN

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

7 | P a g e

FORD 4” UNI-CAM KT2 USB Updater/Additional Licenses

•To verify that this module has been installed previously, you may download the NAV-TV License USB-

Updater to check stored VIN’s used previously, if any. The downloadable ZIP file is located on the NAV-

TV website on the FORD 4” UNI-CAM KT2 product page: https://navtv.com/products/NTV-KIT593/ford-

4-uni-cam-kt2.html

Click on the button at the

bottom to download the zipped folder.

•The FORD 4” UNI-CAM KT2 line features

an option for NAV-TV dealers to

purchase licenses instead of multiple

pieces of hardware, reducing time &

overhead costs. Contact NAV-TV (561-

955-9770) for more information

regarding purchasing one single

programmer, allocated for use in 5, 10,

20 or more vehicles. Additional licenses

may also be sent via email.

•To add a purchased activation license to

your Ford 4” KT2 module, copy and

paste the entire code you were sent

(usually via email). Paste this code into

the ‘Add new license’ section of the USB

License Manager with the module

connected and loaded properly (USB-

UART drivers must be installed. ‘USB

Device’ must be populated with

connected module information).

Double-click to

check VIN usage

Double-click

to add license

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

8 | P a g e

Connecting single camera to screen (expeditors)

•When using the KT2 kit to program multiple vehicles, the install/programming steps remain the same,

but the harness and module (entire kit) must be removed and the video input must be populated to the

screen manually (after being flashed –the radio program will remain). This process is outlined below:

1. If wires already exists on pins 6 & 12 at the screen, cut wires (in half)

and solder the provided female RCA end (NTV-CAB071) onto these wires

(screen side, cut pins off of CAB071) for camera input (ACC power for

camera will need to be found in the vehicle to power the camera –

cigarette adapter is typically used). Isolate the other side of the pair of cut

wires (vehicle side).

2. For all other vehicles with no wires populated on pins 6 & 12 at the screen connector, use the

provided video input cable NTV-CAB071 and

populate the OEM screen connector as follows:

A. Cut the zip tie off of the connector

(replace when this section is complete)

B. Using pick tools, pry both lock tabs to free

the inner 12-pin connector from the outer

sleeve.

C. Slide the inner connector

out of the outer cam-lock

connector.

Lock tab

BHM

10/25/18

NTV-DOC257

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

9 | P a g e