NavePoint Basic Series User manual

© 2019 NavePoint, LLC 20191226—01
OWNER’S MANUAL: Performance Series Wallmount Cabinet
THIS MANUAL APPLIES TO THE FOLLOWING SKUs:
00301081
00301082
00301083
00301074
00301075
00301078
00301079
00301080
00301076
00301077
00301000
Keep this information for further reference.
Thank you for purchasing a NavePoint product.
Please examine the product for any damaged parts. If any part is damaged or missing, contact NavePoint for assistance. Do not attempt to install or
use product if it has been damaged. This product contains small items that could be a choking hazard – keep these items away from children.
During installation, lay product contents on cardboard or other protective surface to avoid any damage.
Do not use with equipment that is heavier than the indicated weight capacity for this product. This product is designed to be installed indoors on wood
stud walls, solid concrete walls or brick walls. Make sure that the supporting surface will safely support the weight of the equipment and all attached
hardware and components. It is recommended that installation be performed by a qualified installer. NavePoint cannot be held responsible for damage
to equipment or personal injury resulting from improper use or installation of product.
Maintenance: Check that the product is secure and safe to use at regular intervals (at least every three months).
Limitations of Liability: In no event will NavePoint, LLC. be liable for any damages, whether direct or indirect, special, punitive, incidental or
consequential damages (including, but not limited to, lost profits or revenue, loss of use, lost business opportunities or loss of goodwill) or for the costs
of procuring substitute products, arising out of or in connection with the use of the product, whether such liability arises from any claim based upon
contract, warranty, tort (including negligence), product liability or otherwise, whether or not seller has been advised of the possibility of such loss or
damage. In no event will seller’s total cumulative liability, from all causes of action and all theories of liability, exceed the total amounts actually paid to
seller by customer under the order that gives rise to any liability hereunder.

www.NavePoint.com 2 [email protected]
1. Parts Identification
1. Top Panel x1
2. Bottom Panel x1
3. Frames x2
4. Front Door x1
5. Side Panels x2
6. Horizontal Beams x4
7. L Type Mounting Brackets x2
8. Back Panel x1
9. Hanger Bar x1
10. Vertical Mounting Rails x4
11. Cable Management Covers x2
Accessories List
A. M6 Screws x12 E. M8 Flange Nut x16
M6 Cage Nuts x12
M6 Plastic Washers x12 F. Casters (Optional) x4 (15U~22U)
B. M6*12 Screws x12 (6U~12U) G. M6 Self-tapping Screw x16 (For Casters)
x24 (15U~22U)
M6 Cage Nuts x12 (6U~12U) H. Lock Kit x1
x24 (15U~22U)
M6 Plastic Washers x12 (6U~12U) I. Anchors x4
x24 (15U~22U)
J. Ground Wire Kit x1
C. M4 Screw x12
White Plastic Washer x1
D. M8*12 Hex Head Screw x16

www.NavePoint.com 3 [email protected]
2. Cabinet Assembly
Detail A
STEP 1.
Lay Bottom Panel (#2) on the hard surface. Insert Front and Rear Frames (#3) with large flange oriented to
the inside. Be sure that the slots in the center of the frames are facing inward as shown in Detail A.
Overlay the Horizontal Beams(#6) so that the notches interlay with large flanges on the Front and Rear Frames
(#3). Be sure to orient the Horizontal Beams (#6) so that the flat, cage nut surface is facing inward.
Attach with 8 M8 Hexagon Screws (Bag D) and 8 M8 Flange Nuts (Bag E).

www.NavePoint.com 4 [email protected]
STEP 2.
Place the Top Panel (#1) on the hard
surface. Turn the assembly over and insert
it into the top panel. Be sure that the Top
and Bottom Panels (#1 and #2) are oriented
in the same direction (front matches front,
back matches back).
Overlay the Horizontal Beams(#6) so that
the notches interlay with large flanges on
the Front and Rear Frames (#3). Be sure to
orient the Horizontal Beams (#6) so that
the flat, cage nut surface is facing inward.
Attach with 8 M8 Hexagon Screws (Bag D)
and 8 M8 Flange Nuts (Bag E).
Detail B
STEP 3.
Install the 4 Vertical Rack Rails (#10) to the Horizontal Beams (#6) at the desired depth using the Cage Nut Kit
provided (Bag A). When determining the appropriate depth, be sure to consider the equipment that you plan
to mount inside the enclosure.
Note: Be sure that the rail depth is the same on both sides of the cabinet.

www.NavePoint.com 5 [email protected]
Detail C
Optional: Mount L Type Mounting Brackets (#7) to the Vertical Mounting Rails on each side of the cabinet
using the Cage Nut Kit provided (Bag A). (Note: To mount the L Type Mounting Brackets (#7), the depth
between front and back vertical rails should be 11’’ (280mm) for 450mm depth cabinet and 16.9’’ (430mm)
for 600mm depth cabinet.)
STEP 4.
Install the two Side Panels (#5) into place
using the Side Panel Latches. Once each
Side Panel (#5) is attached, test to ensure
that each Side Panel Lock locks properly.

www.NavePoint.com 6 [email protected]
STEP 5.
Install the Front Door Lock (Bag H) on the
Front Door (#4) as shown in left picture.
Detail D
STEP 6.
To attach the Front Door (#4) to the cabinet, locate the side with the two pins. Insert the bottom fixed pin
with White Plastic Washer (Bag C) into the door hinge hole. With your thumb, pull down on the top spring
pin and slide it into place over the second door hinge hole and release. NOTE: Each side of the front of the
cabinet has door hinge holes; this allows you to choose the door swing orientation.

www.NavePoint.com 7 [email protected]
STEP 7.
Attach the Back Panel (#8) to the cabinet
using 6 black M4 Screws (Bag C).
Optional: Attach the Top and Bottom Cable
Management (#11) Covers using 4 M4
Screws (Bag C) .

www.NavePoint.com 8 [email protected]
3. Mounting the Cabinet to the wall
Detail E
Attach the Hanger Bar
(#9) to a wall or other
suitable mounting surface
using 4 appropriate
anchors.
Note: When mounting
the mounting plate to the
wall, be sure the 2
mounting hooks are
facing outwards and
away from the wall.
After the Hanger Bar (#9)
has been securely
attached to the mounting
surface, hang the
cabinet’s 2 mounting
notches onto the 2
mounting hooks on the
plate attached to the
wall. The notches will fit
over the hooks and the
enclosure should slide
down onto the hooks
until secure.

www.NavePoint.com 9 [email protected]
After the Hanger Bar (#9)
has been secured and the
cabinet hung properly,
secure the cabinet to the
mounting plate using 2
M4 Screws (Bag C) in the
holes on the mounting
hooks as shown.
Warning: Do not attempt to
mount to wall, when
equipment is mounted
inside cabinet. The cabinet
can hold up to 130 pounds
evenly distributed. Make
sure wall surface can hold
weight of the cabinet and
equipment.
Optional: Attach Casters
(Bag F) with 16 M6 Self
Tapping Screws (Bag G) to
Bottom Panel (#2).
(Optional and only
compatible and included
with 15, 18 and 22U
versions of the
Performance Series
Cabinets)

www.NavePoint.com 10 [email protected]
4. Equipment Installation
1 Rack Unit
-Squared Hole Mounting
1 Locate the numbered square openings in the Vertical Mounting Rails (#10) where you plan to install your
equipment. Install M6 Cage Nuts (Bag B) into the square openings to provide an attachment point for the M6
Mounting Screws (Bag B). Note: Consult your equipment documentation to determine how many cage nuts
will be required and where they will need to be installed.
a- From the inside of the Vertical Mounting Rails (#10), insert one of the flanges of the cage nut through the
square opening. Press it against the side of the square opening.
b- Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square
opening. When the cage nut is properly installed, both flanges will protrude through the square opening and
will be visible on the outer surface of the mounting rail. Repeat steps 1a and 1b until all required cage nuts
are installed.
2 After installing the required cage nuts, use the included M6 Mounting Screws (Bag B) and M6 Plastic
Washers (Bag B) to secure your equipment into the installed M6 Cage Nuts.