Navico R330g User manual

1 Quick Setup Guide V1.0
Router R330g
Quick Setup Guide V1.0

2 Quick Setup Guide V1.0
Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
Part 15.21
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. In cases where the manual is provided only in a
form other than paper, such as on a computer disk or over the Internet, the information required by
this section may be included in the manual in that alternative form, provided the user can
reasonably be expected to have the capability to access information in that form.
This equipment complies with FCC radiation exposure limits set forth for this an
uncontrolled environment. The antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or
transmitter. End users must follow the specific operating instructions for satisfying
RF exposure compliance.
Table of Contents
TABLE OF CONTENTS ............................................................錯誤! 尚未定義書籤。
CHAPTER 1 NAVI R330G’S UICK SETUP ....................................................... 3
1.1 R OUTER M ODE ’ S UICK S ETUP I NSTRUCTION ............................................. 3
1.2 THE I NTRODUCTION OF R OUTER M ODE ’ S UICK S ETUP ................................. 6
1.2.1 Time Zone Setting...................................................................... 7
1.2.2 LAN Interface Setup .................................................................. 8
1.2.3 WAN Interface Setup ................................................................. 9
1.2.3.1 WAN Interface Setup–Static IP .....................錯誤! 尚未定義書籤。
1.2.3.2 WAN Interface Setup– DHCP Client ...............錯誤! 尚未定義書籤。
1.2.3.3 WAN Interface Setup– PPPoE ........................錯誤! 尚未定義書籤。
1.2.3.4 WAN Interface Setup– PPTP..........................錯誤! 尚未定義書籤。
1.2.4 Wireless Basic Settings..................................... 錯誤! 尚未定義書籤。
1.2.5 Wireless Security Setup ....................................錯誤! 尚未定義書籤。
1.2.6 uick Setup Finish ................................................................... 18

3
Quick Setup Guide V1.0
Chapter 1 Navi R330g’s uick Setup
1.1 Router Mode’s uick Setup Instruction
Please open a Microsoft Internet Explorer, and enter http://192.168.1 .1
(Default Gateway) into browser’s blank, then you will see the configuration page
below:
Please input in the blanks, the factory default values for User Name and Password
are “admin” and “admin” (all in lowercase letters); after inputting, please click on
“OK” to enter the homepage as below:

4
Quick Setup Guide V1.0
Please select the “Router”, and then click on “Apply Change”, so you will go to the
page of “System Rebooting”.

5
Quick Setup Guide V1.0
After 6 seconds, you will go back to the main page of “Operation Mode”, and see
the “Router Home” appearing on the left sub-menu, then please click on
“Quick Setup”, and you will see the main page of “Router uick Setup” shown
below, which means you have already enabled the operation mode of “Router
uick Setup”.

6
Quick Setup Guide V1.0
1.2 The Introduction of Router mode’s uick Setup
After you go to the main page of “Router uick Setup”, please click on “Next”
right side below, and go to the next page to do each setting step by step:

7
Quick Setup Guide V1.0
1.2.1 Time Zone Setting
The section provides to change the Time. However, change the router’s date and
time does not affect the date and time on your PCs.
Please click on “Next” button to connect to next step.
Please select your
time Zone

8
Quick Setup Guide V1.0
1.2.2 LAN Interface Setup
If you are using the Mini Router with multiple PCs on your LAN, please set up this
function for multiple users to connect it. The default LAN IP for R33 g is
192.168.1 .1.
Please click on “Next” button to connect to next step.

9
Quick Setup Guide V1.0
1.2.3 WAN Interface Setup
R33 g supports 4 connection types to WAN, select one of the WAN connection
modes required by your ISP in below “WAN Access Type” page, the WAN setting
pages will differ depending on what kind of WAN Type you select.
Please click on “Next” button to connect to next step.

1
Quick Setup Guide V1.0
1.2.3.1 WAN Interface Setup– Static IP
Choose Static IP Address if all WAN IP information is provided to you by your ISP.
R33 g will not accept the IP address if it is not in this format, and the blanks of
“IP Address”, “Subnet Mask” and “Default Gateway” must be input.
Please click on “Next” button to connect to next step.
Input the data provided by ISP
Input the data provided by ISP
Input the data provided by ISP

11
Quick Setup Guide V1.0
1.2.3.2 WAN Interface Setup– DHCP Client
Choose DHCP Client to obtain IP address information automatically from your ISP.
Select this option if your ISP does not give you any IP numbers to use.
Please click on “Next” button to connect to next step.

12
Quick Setup Guide V1.0
1.2.3.3 WAN Interface Setup– PPPoE
If your ISP uses PPPoE connection, your ISP will provide you with a username and
password.
Please click on “Next” button to connect to next step.
Input it by your ISP provided.
Input it by your ISP provided.

13
Quick Setup Guide V1.0
1.2.3.4 WAN Interface Setup– PPTP
Some DSL service providers supply a special DSL modem in Europe or Big Pond
Cable in Australia. This kind of modem only supports the PPTP tunnel to access
the Internet; Please enter the account’s information of Account and Password
which provided by your ISP.
Please click on “Next” button to connect to next step.
IP Address, Server IP
Address and Subnet Mask are
all input as necessary.

14
Quick Setup Guide V1.0
1.2.4 Wireless Basic Settings
The first step of setting up the “Wireless Basic Settings” is to give a name for
SSID, herewith the default name of SSID is Navi_R330g, it’s suggested to use.
Please click on “Next” button to connect to next step.
Select the
suitable
item for you to use.
I
t
’
s suggested to use.

15
Quick Setup Guide V1.0
1.2.5 Wireless Security Setup
The “Encryption” item of “Wireless Security Setup” is optional; which means you
can choose it under your demand, herewith it’s divided into two categories of
“WEP” and “WPA”, if you want to protect your transmitting data; you can select it
depended on the level of your request.
Please follow the instruction below to complete “Wireless Security Setup”.
a. Wireless—WEP mode
After you select “WEP”, you will see the picture below:
It’s an optional item.

16
Quick Setup Guide V1.0
No matter if you selection is either 1 or 26 hexadecimal digits ( ~9, a~f, and A~F)
in the pull-down menu bar of “Key Format”; it will be based on whether you select
64-bits or 128-bits in the “Key Length” pull-down menu. After you select it, there
will be 4 “Encryption Keys” generated automatically; please input it with data, such
as: WEP-64bit key: 1 hexadecimal digits ( ~9, a~f, and A~F). WEP-128bit key:
26 hexadecimal digits ( ~9, a~f, and A~F). As for the “Default Tx key”, it lets you
specify which of the four encryption keys you use to transmit the data on your
wireless LAN.
b. Wireless—WPA mode
The WPA mode is recommended when you want to have better security. Once the
WPA mode is used, the authentication methods of “TKIP” and “AES” will be applied.
WPA (TKIP):
It stands for Temporal Key Integrity Protocol (TKIP), TKIP will verify the
security configuration after your encryption keys are determined.
WPA2 (AES):
It stands for Advanced Encryption Standard (AES), it is a symmetric
128-bitblock data technique, which it works simultaneously on differently
multiple network layers.
It has low level (64-bit) and high level
(128-bit).
It has “10 characters” and “26
characters”; it will be listed under
your selection is low level (64-bit)
or high level (128-bit).

17
Quick Setup Guide V1.0
After setting up, please click on Finished” button to connect to next step.
Select it by your request
Please input it as necessary
Please select it under your demand

18
Quick Setup Guide V1.0
1.2.6 uick Setup Finish
The Quick Setup has been completed successfully when you see this
screen.
The system will be rebooting automatically and goes to the Product’s Diagram
Homepage after 6 seconds.