Navman A300 Sport.Tool Service manual

A300
Setting options
NAVMAN
Press and hold to enter setup
Press repeatedly to step through the setting options.
Press both buttons together ( ) to start or stop editing
a setting option.
While editing, press or repeatedly to step through selectable states,
or increase/decrease values. Press and hold the appropriate button to
increase/decrease values quickly.
Set (12hr)
lets you set 12hr or 24hr time format
Set (31-12)
lets you set dd-mm or mm-dd date format
Calc up
When ‘calc up’ is «ON» the A300 calculates data for all
movement (uphill and downhill). When ‘calc up’ is «OFF» the
A300 calculates information for downhill movement only.
Beep
When beep is «ON» a beep will sound when the buttons are
pushed.
Set units (km/h)
lets you set speed units to «km/h» or «mph»
Distance and altitude are displayed in units corresponding to the speed
units, i.e. if you choose «km/h» for speed units, then distance is displayed
in «km» and altitude in «m».
Set offset
lets you adjust the A300 to display local time
The date is displayed to ensure that time adjustments are made in the
correct direction, i.e. both correct time and correct date should be
displayed. GPS signals must be obtained to set local time.
Press and hold to leave setup
A300 — Settings

A300
KEY
= press this button
= press this button
= press both buttons together
Use the settings
NAVMAN
settings editing details
edit accept
A300 — Settings
beep beep
beep ON
beep OFF
set units (km/h)
set units (mph)
set units (km/h)
set offset
set 12hr
set 31-12
set 24hr
set 12-31
set units (km/h)
set (12hr) set (12hr)
set (31-12)set (31-12)
time (date)
Calc up
Calc up ON
Calc up OFF
Calc up
�
�
edit accept
edit accept
edit accept
edit accept
edit accept

A300
Normal operating modes
Press to start normal operation
Press repeatedly to step through the modes (hold to
cycle automatically through modes).
Speed
shows session distance and current speed
Speed (AVG)
shows session distance and average speed
Speed (MAX)
shows session distance and maximum speed
Odometer
shows total distance
Altitude
shows total accumulated altitude and current altitude
Clock
shows the current time and date
(You may need to adjust the settings to display your local time)
Timer
shows session and lap times
The timer starts automatically whenever you start moving and stops
whenever you stop moving.
Timer Recall
lets you recall stored lap data. Repeatedly pressing recalls
lap data starting from the last stored lap, then lap 1, 2, 3 etc.
Press and hold to shut down the A300
NAVMAN A300 — Modes

A300
Use the modes
*
*
*
*
*
*
*
*
Speed (AVG)
Speed (MAX)
Speed
modes operating details
KEY
= press this button
= press this button
= press both buttons together
= press and hold both buttons together
Clock
Timer
Odometer
clear all* session data
Timer recall
Altitude
store current lap data
clear all* session data
store current lap data
clear max speed only
store current lap data
clear odometer only
store current lap data
clear accumulated altitude only
store current lap data
clear all* session data
store current lap data
clear all* session data
store current lap data
restart recall from lap 1
recall lap data
NAVMAN A300 — Modes
(*Does not clear odometer)
AVG
MAX
RCL
83 72

A300
QUICK START GUIDE

A300
NOW YOU KNOW.

A300
Be outdoors
The A300 is not intended for operation indoors or under
water as it uses Global Positioning System (GPS) satellites to
get time and date information, and to calculate distance and
speed. For best results, always use the A300 outdoors with
an unobstructed view of the sky.
L
1. Turn D-ring anti-clockwise and slide enclosure cover down to open
battery enclosure.
2. Insert battery with «» end as indicated inside enclosure.
3. Replace enclosure cover (ensuring lugs at the bottom of the cover are
aligned with slots in the enclosure surround), turn D-ring clockwise to
seal.
Get ready
Step 1
Fit the battery
Fit the A300
The A300 is designed to be worn on the left upper arm.
You may wish to adjust some of the settings prior to fitting.
For best performance:
General use = Alkaline
Below 5 oC = NiMH
!

A300
The control buttons, and (as shown above) are pressed
separately or together to turn the unit «ON» and «OFF», cycle
through modes, and select mode options.
Know the buttons
Get set
Step 2
!Always enter setup first if you wish to change settings.
To enter setup after starting normal operation, you must
shut down and re-start the A300.
Flashing icon = seeking GPS signals
Constant icon = GPS signals obtained
Startup could take up to 80 seconds to get all satellite data.
If you release before the counter reaches zero, the A300
will immediately start normal operation.
For details about system settings see over page or consult User Guide.
Press and hold to leave setup
counter
counter
After leaving setup, the A300 automatically starts normal
operation displaying the speed mode first.
Enter setup
Press and hold to enter setup
Know the startup options
1. enter setup
2. start normal operation

A300
Start normal operation
Press to start normal operation
When starting directly into normal operation A300 will start in
the mode it was in at last shutdown.
The A300 automatically operates whenever you are moving
and pauses operation while you are stationary. Modes are
accessed in the following order:
Go
Step 3
Mode icons appear in the lower section of the screen. While
in Speed mode you can monitor session distance and current
speed. You can also store laps and clear session data.
While in Speed mode
Press to store lap data
Press and hold to clear all* session data
Press to go to next mode
(*Does not clear odometer)
When you want to shut down the A300
Press and hold
Now you know
speed mode icon
session distance
current speed
For details about modes see over page or consult User Guide.
Mode example (speed)
83 72
Speed Speed AVG Speed MAX Odometer
AltitudeClockTimer
Timer RCL
RCL
MAX
AVG

LA000525B © 2005 Navman NZ Ltd. All rights reserved. Sport.Tool’ and ‘Now you know.’ are trademarks of Navman NZ Ltd.