NBS-Cam HD964 User manual

UserGuide
HD964&HD991
HD Color LCD Monitor
Quad-view (7”）/（10.1”)
Please read this manual thoroughly before operating the unit,
and keep it for future reference.
V1711.01
1.855.730.5555
www.nbs-cam.com

CONTENT
1. Precautions 3
2. Accessories 5
3. Connections 6
4. Specifications 7
5. Menu operation and functional specification 8
5.1 IR remote control 8
5.2 Menu operation 9
5.2.1 Desktop 9
5.2.2 Home menu 10
5.2.3 Volume 10
5.2.4 Mode 11
5.2.5 Source 11
5.2.6 Setting 12
1.855.730.5555
www.nbs-cam.com

1.PRECAUTIONS
●Storageandkeeping
1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30~+80℃, and the
operating temperature is -20~+70 ℃. Battery operating temperature is 0-70℃. The humidity is RH90%
2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places.
3. Never use this device in environments with excessive moisture, dust or smoke.
4. Avoid dropping or striking this device.
5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts.
6. Never puncture, scratch or use abrasive cleaning materials on this device.
7. Do not place cables where they may be pinched or stepped on.
8. Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow adequate air circulation
around the device.
9. The monitor is not designed to be waterproof.
●Operatingprecautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2. Make sure all cables are connected properly. Observe polarity. Improper cable connections may damage the
monitor. Remove the power cable connections when you do not intend to use the unit.
3. The back-up battery can be recharged when the power is on.
4. When it is fully charged, recharging stops automatically.
5. It may take longer time to charge if being unused for a long time.
WARNING!
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring only.
SPECIAL NOTICE
Occasionally, a few highlights or dark spots may occur on the LCD sc
reen. This is a very common phenomenon in active
matrix display technology, and doesn't necessarily indicate any defects or faults. Never try to repair this device by
yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The
monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.
1.855.730.5555
www.nbs-cam.com
-3-

1.PRECAUTIONS
●Maintenance
1. Remove all the cable connections from the monitor before cleaning the device.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth.
3. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your
warrantee and necessitate expensive repairs.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user not to dispose of electrical and electronic equipment.
1.855.730.5555
www.nbs-cam.com
-4-

2.ACCESSORIES
U Support Bracket Center Mount Bracket
Sun shield
Power cable
Angle adjustment screws
IR remote control
SPECIAL NOTICE
Accessory supply may be different for different application.
1.855.730.5555
www.nbs-cam.com
-5-

3.CONNECTION
1.855.730.5555
www.nbs-cam.com
-6-

4.SPECIFICATIONS
HD Color LCD Quad-view Monitor（7”）/（10.1”）
MH964（7”）/ MH991（10.1”）
7” & 10.1” HD quad-view monitor with LVDS interface, support high resolution 1280*800.
Support 4 x camera inputs in 720P / 1080P and multiple TV system like PAL / NTSC / HD-AHD / HD-TVI / HD-CVI, and 1080P
video input.
Image can be set to horizontally/vertically flipped, normal/mirror image; menu characters remain same while setting to
mirror image.
Support multiple image display modes like single, dual, triplex, quad, trefoil, Y-split, H-split.
Support 1 x HDMI video input, for easy connection to PC or smart electronic devices, etc.
Support 1 x VGA video input and resolution can be 1080P.
Support 1 x CVBS video input for DVD.
Support Wi-Fi display for synchronous display on Mobile or tablet, etc.
Capacitive touch-screen.
Support 5 x triggers, trigger priority & trigger delay are selectable.
Support auto scan, scan channel and scan time are selectable.
Support backlight adjustment manually in 3 levels and automatically.
Parking line.
With 1.5W speaker.
Monitor operated by buttons, remote control or touch-screen.
Support 9 languages OSD (English, German, Japanese, Russian, Chinese, Italian, Spanish, French, Dutch).
Working voltage: 10-32V, with short circuit protection and short circuit alarm function.
Compliance with CE/FCC/EAMARK standards
1.855.730.5555
www.nbs-cam.com
-7-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
●IRRemotecontrol
●MUTE (Mute):
Press to select ENABLE/MUTE sound.
●POWER (Power switch):
Turn on or enter standby mode
●VOL:
Volume decrease and menu selection left
●VOL:
Volume increase and menu selection right
●MENU:
Call home menu or return to previous menu.
●UP:
Move up the menu cursor, or switch screen display mode when there is no
pop-up menu and signal source is selected as camera
●DOWN:
Move down the menu cursor, or switch screen display mode when there is no
pop-up menu and signal source is selected as camera
●MODE:
Switch input source in the order: CAMERA->HDMI->WI-FI->DVD->VGA
●SEL :
Confirmation button
●P/N:
When signal source is selected as camera, switch TV system under screen split mode in the order:
NTSC -> PAL -> 720P 60HZ -> 720P 50HZ-> 1080 I60HZ-> 1080 I50HZ
●LANG:
Enter the Language setup Menu
●REST:
System reset button
●AV:
Switch to or exit DVD
NOTICE
1. Please align the remote control with the infrared-receiving
window on the monitor to operate.
2. Never disassemble the remote control or allow it to drop, or
become wet.
3. Press the control buttons firmly. Allow 2 seconds for the
picture to change.
1.855.730.5555
www.nbs-cam.com
-8-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
●Menuoperation
1.Desktop
●When Home Menu does not pop up, its achievable operations are as follows,
●Touch the Red border to pop up home menu
●When signal source is selected to be cameras, image display mode can be switched by sliding to left/right on screen.
in the order: CAMERA1->CAMERA2->CAMERA3->CAMERA4->DOUBLE->TRIPLE->TREFOIL->Y-SPLIT->H SPLIT->QUAD->CAMERA1;
●Touch the camera channel under multi-split screen mode to zoom into a single full screen and touch it again to get
back to multi-split screen.
1.855.730.5555
www.nbs-cam.com
-9-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
2.Home
●Touch the area out of the red border to get back to Desktop.
3.Volume
●Press VOL+, VOL- and MUTE button on remote control to adjust volume or set up mute; the value displaying on the bar
represents current volume.
●Directly drag the slider on the screen to adjust volume.
●Click speaker icon to turn on/off Mute
1.855.730.5555
www.nbs-cam.com
-10-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
4.Mode
Mode setting interface（display mode selection. Its achievable operations are as follow,
●Press Up, Down, Vol- and Vol+ on remote control to move the cursor up / down / left / right, then press Sel to switch to the
corresponding display mode;
●The corresponding screen display modes can be switched by touching the icons on OSD.
5.Source
Source interface (signal source selecting). Operation is as Mode menu.
●Support automatic identification for signal output
●Supports standard definition (NTSC \ PAL) and high definition format like AHD, TVI and CVI; Supports resolution up to
1080P30Hz.
●Multiple HDMI and VGA input resolutions:
640x480, 720x480, 720x576, 800x600, 1024x768, 1280x720, 1280x1024, 1366x768, 1440x900, 1600x900, 1920x1080.
1.855.730.5555
www.nbs-cam.com
-11-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
6.Setting
Setting menu interface (for other functions). Operation is as Mode menu.
6.1Camerasetting
Camera menu (settings for Camera channel attribute).
●To set other channels, press Menu on IR remote control and move the cursor to the channel selection area (shown as red
border). Press Up，Down，Vol- and Vol+ to select the channel and press Sel to switch to the corresponding channel for attribute
settings.
Camera Name setting interface (setting for each channel’s name).
●Camera name digits can be 8 in max.
1.855.730.5555
www.nbs-cam.com
-12-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
6.2Parkingline
Parking Line setting interface (setting for reverse grid).
●Touch CALIBRATE icon to set reverse cursor.
●Press SEL or touch TYPE1/TYPE2 on screen to switch reverse cursor mode and drag the cursor directly to adjust.
6.3Language
Language setting interface (setting for system language).
6.4Trigger
Trigger setting interface (setting for trigger function).
●Trigger delay range: 1~60s;
1.855.730.5555
www.nbs-cam.com
-13-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
●Trigger priority: 1~5;
●Trigger function takes priority over Auto Scan function.
●When there is trigger, signal source will be automatically switched to the working Camera. It will be back to the previous ●
signal source after the trigger ends.
●Support standby trigger.
Trigger Delay / Priority setting interface
Trigger Display setting interface (setting for display mode of
the fifth trigger)
Trigger Display setting only acts on the fifth trigger wire
6.5AutoScan
Auto Scan setting interface
●Auto Scan Delay Range: 1~60s.
1.855.730.5555
www.nbs-cam.com
-14-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
6.6PowerOn
Power- On setting interface (power-on screen display mode setting).
●Power On setting only acts when power-on signal source is Camera.
6.7Standard
Standard setting interface (TV system setting in split-screen display mode)
1.855.730.5555
www.nbs-cam.com
-15-

5.MENUOPERATIONANDFUNCTIONALSPECIFICATION
Standard setting is only for multi-split screen display modes;
●Multi-Split screen display mode supports camera inputs in different resolution
●when camera input resolution is lower than the size of its corresponding split screen, it will be centered display in the original
scale, conversely, it will zoom out to be split screen in full format.
●NTSC Camera of standard definition only displays in NTSC、720P60Hz and 1080I60Hz, PAL Camera only displays in PAL、
720P50Hz and 1080I50Hz.
6.8System
System setting interface.
●When Menu Lock is set ON, screen touching control will be disabled.
1.855.730.5555
www.nbs-cam.com
-16-

5.MENUETCONFIGURATIONS
Le réglage standard est uniquement pour les modes d'affichage à écran partagé
● Le mode d'affichage d'écran partagé prend en charge les entrées de caméra dans différentes résolutions
● Lorsque la résolution caméra est inférieure à la taille de l'écran partagé correspondant, l'affichage sera centré selon la
résolution d'origine. Inversement, il effectuera un zoom arrière pour afficher l'écran divisé en plein format.
● La caméra NTSC de définition standard ne s'affiche qu'en NTSC, 720P60Hz et 1080I60Hz, la caméra PAL ne s'affiche qu'en PAL,
720P50Hz et 1080I50Hz.
6.8Système
● Lorsque le Menu Lock est activé, le contrôle tactile de l'écran sera désactivé.
1.855.730.5555
www.nbs-cam.com
-16-

5.MENUETCONFIGURATIONS
6.6Alimentation(PowerOn)
●Le réglage d’alimentation « power on » ne fonctionne que lorsque la source de signal de «power on » est Camera.
6.7Format(Standard)
1.855.730.5555
www.nbs-cam.com
-15-

5.MENUETCONFIGURATIONS
Réglage de la fonction déclenchement automatique (Trigger).
● Période de retard (délais): 1~60s;
● Priorité de déclenchement: 1~5;
● La fonction de déclenchement est prioritaire sur la fonction de balayage automatique.
● Lorsque le déclenchement s’effectue, le signal source bascule automatiquement vers la caméra activée. Il revient à la source
de signal précédente une fois le déclenchement terminé.
● Mode veille pour le déclencheur.
Réglage du retard de déclenchement / P
riorité de
déclenchement
Réglage pour le mode d'affichage du cinquième déclencheur.
(l’afficage n’agit que sur le 5efil de déclenchement).
6.5Balayageautomatique(AutoScan)
● Période de délais: 1~60s.
1.855.730.5555
www.nbs-cam.com
-14-

5.MENUETCONFIGURATIONS
6.2Ligned’arrêt (marchearrière)
● Touchez l’icône CALIBRATE pour définir la marche arrière.
● Appuyez sur SEL ou appuyez sur TYPE1 / TYPE2 sur l'écran pour passer en mode «Marche Arrière » et faites glisser
le curseur pour ajuster.
6.3Langue
● Appuyez pour sélectionner la langue d’affichage : Anglais, Allemand, Français, Espagnol, Portugais, Italien, Néerlandais ou
Russe.
6.4Gâchette(Trigger)
1.855.730.5555
www.nbs-cam.com
-13-