NBS-Cam MC727 User manual

UserGuide
MC727
Digital LCD Color Monitor
Single view
（
7”
）
Please read this manual thoroughly before operating the unit,
and keep it for future reference.
V1711.01
1.855.730.5555
www.nbs-cam.com

CONTENT
1. Precautions 3
2. Product features 5
3. Technical specifications 5
4. Accessories 6
5. Parts identification 7
6. Remote control operation 8
7. Basic operation 9
8. Menu 12
1. Image 12
2. Option 13
3. System 14
9. Troubleshooting 14
1.855.730.5555
www.nbs-cam.com

1.PRECAUTIONS
●Storageandkeeping
1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30~+80℃, and the
operating temperature is -20~+70 ℃. The humidity is RH90%
2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places.
3. Never use this device in environments with excessive moisture, dust or smoke.
4. Avoid dropping or striking this device.
5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts.
6. Never puncture, scratch or use abrasive cleaning materials on this device.
7. Do not place cables where they may be pinched or stepped on.
8. Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow adequate air circulation
around the device.
9. The monitor is not designed to be waterproof.
●Operatingprecautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2. Make sure all cables are connected properly. Observe polarity. Improper cable connections may damage the
monitor. Remove the power cable connections when you do not intend to use the unit.
WARNING!
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.
SPECIAL NOTICE
Occasionall
y, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active
matrix display technology, and doesn't necessarily indicate any defects or faults. Never try to repair this device by
yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The
monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.
1.855.730.5555
www.nbs-cam.com
-3-

1.PRECAUTIONS
●Maintenance
1. Remove all the cable connections from the monitor before cleaning the device.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth.
3. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your
warrantee and necessitate expensive repairs.
●Declarationofconformity
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user not to dispose of electrical and electronic equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
la FCC (Comisión Federal de Comunicaciones). El funcionamien to está sujeto a
dos condiciones:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
1.855.730.5555
www.nbs-cam.com
-4-

2.PRODUCTFEATURES
1. TFT LCD monitor with wide angle view and high resolution display.
2. Select from 8 languages for user operation.
3. Multiple video formats: PAL/AUTO/NTSC.
4. 1 camera input, 1 reversing trigger wire.
5. Power supply to camera.
6. Operates from 10 -32V. Supports 12V or 24V.
7. Picture image may be adjusted for Horizontal, Vertical, Mirror and Normal viewing.
8. On-board speaker.
9. Full-function remote control.
10. Automatic brightness control.
11. The scale can be adjusted for left, right, up and down.
3.TECHNICALSPECIFICATIONS
1. Monitor: 7" TFT-LCD Color monitor with digital panel.
2. Audio output: 1.5 W.
3. Loudspeaker: one 15x24mm round loudspeaker.
4. Power supply: Automobile storage battery (DC / 10-32V).
5. Power consumption: about 6W.
6. Outer dimension:
Without flush moun t with flush mount
182mm (W) 198mm (W)
122mm (H) 138mm (H)
26mm (T) 31mm (T)
7. Dot pitch: 0.0642(W) x 0.1790(H).
8. Resolution: 800×3 (RGB) × 480.
9. Contrast: 500:1.
10. Brightness: 400cd/m2.
11. Viewing angle: U: 50° D: 70°, R/L: 70°/70°.
12. Operating temperature: -20~+70ºC, RH90%.
13. Storage temperature: -30~+80ºC, RH90%.
SPECIAL NOTICE
All specifications are subject to change without notice.
1.855.730.5555
www.nbs-cam.com
-5-

4.ACCESSORIES
U Support Bracket Optional Center Mount Bracket
AV and Power supply adapter cable
IR remote control
Sun shield Detaching piece (optional)
Angle adjustment screws
Flush mount (Optional)
SPECIAL NOTICE
Accessory supply may be different for different application.
1.855.730.5555
www.nbs-cam.com
-6-

5.MONITORCOMPONENTS
Digital color LCD screen
Power indicator
Remote control sensor
Light level sensor
Power switch
Brightness increase
Brightness decrease Setting selection down
Menu
Loudspeaker
Mounting bracket installation
1.855.730.5555
www.nbs-cam.com
-7-

7.BASISOPERATION
NOTICE
1. Please align the remote control with the infrared-receiving window on the monitor to operate.
2. Never disassemble the remote control or allow it to drop, or become wet.
3. Press the control buttons firmly. Allow 2 seconds for the picture to change.
Mute
Setting selection down
Horizontal flip
Less brightness
Picture mode
Language selection
Call PAL – AUTO - NTSC
Menu
Timer
More brightness
Vertical flip
Power switch
Setting selection up
1.855.730.5555
www.nbs-cam.com
-8-

7.BASISOPERATION
●
MUTE (Mute):
Press to select ENABLE/MUTE sound.
●
POWER (Power switch):
Press to turn on/off the monitor.
●
(Horizontal turning of picture):
Press to turn picture horizontally.
●
(Vertical turning of picture):
Press to turn picture vertically.
●
CH+ (Channel selection up):
Press to select the upper setting.
●
CH- (Channel selection down):
Press to select the lower setting or to display the scale.
●
Press to decrease Brightness.
●
Press to increase Brightness.
●
MENU:
Press to show menu.
●
MODE (Picture mode):
Press to select different picture modes (PERSONAL / STANDARD / SOFT / VIVID / LIGHT).
●
CALL (Call)
Press to display video channel source.
●
TIMER:
Press to set the timer to shut down monitor (10, 20, 30, 40 and max 90 minutes).
●
LANG (Language selection):
Press to select language of display:English, German, French, Spanish, Portuguese, Italian, Dutch or Russian.
●
SYS:
Press to select; PAL / AUTO / NTSC.
1.855.730.5555
www.nbs-cam.com
-9-

7.BASISOPERATION
●ConnectionofAVadaptorandcontrollercable
Hold the cable, align the side of jack marked with on the female
6-pin connector with the male 6-pin connector marked with then
firmly plug together.
①Brown 4 pin male for Camera1.
②Single red wire to power wire of DC / 10-32V
③Single black wire to GND.
④Single brown wire to positive power wire of the back-up light.
Brown 4 pin male for Camera 1.
Single red wire to positive power supply of DC / 10-32V.
Single black wire to GND.
Single brown wire to positive power wire of back-up light.
●Removingthemonitor
1. Insert the detaching piece as indicated by the white arrow. Press in and lift up, the
monitor will be released from the flush mount.
2. Remove the monitor.
1.855.730.5555
www.nbs-cam.com
-10-

7.BASISOPERATION
●Reversingdisplay
1. When the brown wire is connected to the positive wire of back-up light, the monitor automatically
switches to CAM 1 (back-up camera) when the back-up light is turned on. The distancing grid will also be
displayed.
8.MENU
Press MENU to display the following options and settings:
1. Picture
2. Option
3. System
●Picture
VOLUME, BRIGHT, CONTRAST, COLOR, AUTO DIM and SCALE ADJUST options will display on the screen as illustrated below:
PressCH-toselectBRIGHT.
PICTURE
BRIGHT 50
CONTRAST 50
COLOR 50
VOLUME 50
AUTO DIM OFF
SCALE ADJUST OFF
Press to adjust the brightness level.
1.855.730.5555
www.nbs-cam.com
-11-

8.MENU
Whenautodimisturnedonin darkenvironment,OSDturnsintodimmodefordimsetting.Whenautodimisturnedon/off
inbrightenvironment,OSDdisplaysnormalmode.
Dim Mode Normal mode
PICTURE PICTURE
BRIGHT 40 BRIGHT 50
CONTRAST 45 CONTRAST 50
COLOR
40
COLOR
50
VOLUME 50 VOLUME 50
AUTO DIM ON AUTO DIM ON
SCALE ADJUST OFF SCALE ADJUST OFF
PressCH-toselectSCALEADJUST.
PICTURE
BRIGHT 50
CONTRAST 50
COLOR 50
VOLUME 50
AUTO DIM
ON
SCALE ADJUST OFF
Press to select or for sacle adjust.
ExitmenuandagainpressCH-todisplaythegridline.
If is selected, press to adjust the scale up/down. If is selected press to adjust the scale left/right.
1.855.730.5555
www.nbs-cam.com
-12-

8.MENU
●Option
LANG, SCALE, CAM1 options display on the screen as illustrated below:
PressCH-toselectLANG
OPTION
LANG ENGLISH
SCALE ON
CAM1 Normal
Press to select:English, German, French, Spanish, Portuguese, Italian, Dutch or Russian.
PressCH-toselectSCALE PressCH-toselectCAM1
OPTION OPTION
LANG ENGLISH LANG ENGLISH
SCALE ON SCALE ON
CAM1 Normal CAM1 Normal
Press To select ON/OFF. Scale refers to the Press to select NORMAL / MIRROR.
reversing distance indicator displayed on the monitor.
●System
COLOR-SYS, HORIZONTAL, VERTICAL, ZOOM functions will display on the screen as illustrated below:
PressCH-toselectCOLOR-SYS.
SYSTEM
COLOR-SY AUTO
BLUE BACK ON
HORIZONTAL
VERTICAL
ZOOM 16 :9
Press to select PAL / AUTO / NTSC.
1.855.730.5555
www.nbs-cam.com
-13-

8.MENU
PressCH-toselectBLUEBACK. PressCH-toselectZOOM.
SYSTEM SYSTEM
COLOR-SY AUTO COLOR-SY AUTO
BLUE BACK ON BLUE BACK ON
HORIZONTAL HORIZONTAL
VERTICAL
VERTICAL
ZOOM
16 :9
ZOOM
16 :9
Press to select ON/OFF. Press to select 16 :9 or 4 :3.
9.TROUBLESHOOTING
The symptoms described below do not necessarily mean a failure within the display. Please check the following items before
you initiate request for repair.
PROBLEMS POSSIBLESCAUSES/SOLUTIONS
No picture, no sound Improper connection of automobile adapter. Use of un-authorized
power supply. Power switch is on OFF position.
No picture Check whether AV cable is properly connected.
No sound Check whether audio wire is properly connected or the sound
volume is turned off or set too low.
Dark picture Check whether brightness and contrast are adjusted correctly; Check
whether the environments temperature is too low.
No color Adjust the color settings.
Upside down or lateral inverted picture Use the remote control horizontal /vertical selection switch to set
proper orientation.
No reversing function (i.e. Picture) The black wire of the monitor AV cable to the reversing light may be
loose. The red wire from the monitor may be loose.
1.855.730.5555
www.nbs-cam.com
-14-