NCR 7409 K303 Use and care manual

7409‐K303
BarCodeScanner
Replacement
KitInstructions

IssueA

Revision Record
Issue Date Remarks
AApr2011Firstissue
 
 

1
Introduction
Usetheseinstructionstoreplacethe7409‐K300/K305BarCodeScannermounting
bracketswiththe7409‐K302brackets.
7409-K300 7409-K305
7409-K303


2
Kit Contents
2
9550
Fixed Angle Mount Cable Cover
497-0467789
MS3207 Scanner Cable, DB9 to USB, 1 m
497-0466203
Screw, 6-32 x 0.375, Phillips, Pan
006-8613117
Screw, M3xPo.5 x 6 mm, Phillips, Flat Hd
006-8612557
Fixed Angle Mount Scanner Faceplate
497-0472462
Fixed Angle Mount Scanner Mount
497-0472477
Class 2 Laser Warning Label
497-0460286
Nut, 6-32, KEPS
006-8611426


3
Installation Procedures
1. Unplugtheterminal’spowercordandturnoffthepowertoanyconnected
peripheraldevices.
2. Removethecurrentscannerassembly(7409‐K300or7409‐K305).
Removing 7409-K300
3. Opentheunittotheserviceposition.
a. Removethescrews(2)inthesidesoftheFixedAngleMount.
Screw
(One On Each Side)


4
b. TiltthedisplayasshownandrestthedisplayontheDisplaySupport.
2954
4
Display Support

Note: PlacetheDisplaySupportbehindtheextensiononthenDisplayHinge
Bracket.
24753
Display Support
Bracket Extension


5
4. Removethescrews(3)thatsecuretheScannerBrackettotheterminalcabinet.
RemovetheassemblyanddisconnecttheScannerCablefromtheterminal.
2954
3
Display Support
7409-K300 Bar
Code Scanner

5. DisconnecttheScannerCablefromthescanner.Discardthiscable.
6. RemovetheBarCodeScannerfromtheScannerMountingBracket(3screws).
Discardthebracketbutretainthescrews.
2
95
4
1


6
Removing 7409-K305
1. Opentheunittotheserviceposition.
a. Removethescrews(2)inthesidesoftheFixedAngleMount.
Screw
(One On Each Side)


7
b. TiltthedisplayasshownandrestthedisplayontheDisplaySupport.

Note: PlacetheDisplaySupportbehindtheextensiononthenDisplayHinge
Bracket.
24753
Display Support
Bracket Extension


8
2. Removethescrews(2)thatsecuretheScannerBrackettotheterminalcabinet.
RemovetheassemblyanddisconnecttheScannerCablefromtheterminal.

3. DisconnecttheScannerCablefromthescanner.Discardthiscable.
4. RemovetheBarCodeScannerfromtheScannerMountingBracket(3screws).
Discardthebracketbutretainthescrews.


9
Assembling the new bracket assembly
1. AssembletheScannerFaceplateandScannerMountingBracket(2hexnuts).
2
9538
Scanner Faceplate
Scanner Mounting Bracket

2. InstalltheBarCodeScannerontheScannerMountingBracket(3screws).
2
9539
Bar Code Scanner

3. Connectthenew1meterScannerCabletothescanner.
2
95
4
0


10
4. 7409‐K300Only:RemovetheBlankFaceplate.
a. Removethescrews(2)thatsecuretheBlankFaceplate.
b. PivotthetopoftheBlankFaceplateoutatthetopasshowntoremoveitfrom
theFixedAngleMount.
2954
5
7409-K036 Blank Faceplate


11
5. HookthebottomofthenewScannerFaceplateontothebottomedgeofthe
openingontheFixedAngleMountandthensecuretheassemblywithscrews(2).
2
95
4
6

6. RoutetheScannerCablethroughtheBracketCableGuidesonthebackofthe
terminalandthenconnectittoaUSBconnectorontheI/OPanel.
29547


12
7. InstalltheCableCoverontheterminal(usethesamethreescrewholesthatwere
usedtomountthepreviousscannerassembly.
2952
2
Cable Cover

8. AdheretheSafetyLabelontheScannerMountingBracketasshown.
2954
8
Safety Label

9. ClosetheDisplayandsecureitwithscrews(2).