NCR 7409-K360 Manual

7409‐K360
FixedAngleMountMSRand
BarCodeScanner
KitInstructions

IssueA

Revision Record
Issue Date Remarks
AOct2009Firstissue
 
 

1
Introduction
ThiskitprovidesaMagneticStripeReaderandBarCodeReaderfortheNCR
EasyPointAdvantage(7404)andNCRSelfServ60(7409).Theassemblyinstallsonthe
frontofthe7409‐K035FixedAngleMount.
27961 

2
Installation Procedures
1. Hookthebottomofthebracketontothebottomedgeoftheopeningonthefront
oftheFixedAngleMount.
2. Securethebracketwithscrews(2).
27964


3
3. RemovetheCableCoverfromtheterminalandconnectthecablestotheI/O
Panel.
•ConnecttheScannerCabletoaUSBconnector.
•ConnecttheMSRDataCabletoaUSBconnector.
•ConnecttheMSRPowerCabletoapoweredRS‐232connector.Whichever
RS‐232portisuseditmustbesetto12V.SeeJumperSettingssection.
7409 Connections
27661a
RS232/B RS232/A A
B
Line Out 2 Line Out 1Mic Power
D V I - I
DC In LAN C
D
E
F
USB PortsTerminal Power RS-232 Ports 
7404 Connections
27660a
Mic Out Mic In
COM4 COM3 COM2 COM1
USBUSB
Parallel
On/Off DC Power
Cash Drw LAN
USB Ports Terminal Power
Powered RS-232 Ports 
4. ReplacetheCableCover.
5. ClosetheDisplayandsecureitwithscrews(2).

4
Jumper Settings
7404
Thefollowingdiagramsillustratethejumpersettingsforthe7404Motherboard.
Defaultsettingsareshown.
Powered RS-232 Ports (COM3 – COM4)
23842
COM3/COM4 - JP3
12
1
COM3 +5V
COM3 +12V
Pin 3 - 4
Pin 1 - 2
Pin 5 - 6
COM3 Ring Indicator
COM4 +5V
COM4 +12V
Pin 9 - 10
Pin 7 - 8
Pin 11 - 12
COM4 Ring Indicator


5
7409
Thetwoserialportsonthe7409I/OBoardhavejumperoptionsforeitherRing
Indicator(RI),fused+12V,orfused+5V.Whensettopoweredeachportiscapableof
supportingupto1.5A(Max.)andisprotectedwithself‐healingpoly‐fuse.The
defaultsettingisRingIndicator.ThepowerisselectablebyJP4.
26705c
COMA/COMB - JP4
12
1
COMA +5V
COMA +12V
Pin 3 - 4
Pin 1 - 2
Pin 5 - 6 COMA Ring Indicator *
COMB +5V
COMB +12V
Pin 9 - 10
Pin 7 - 8
Pin 11 - 12 COMB Ring Indicator *
* Default settings



6
7409 Restrictions for USB Devices if Using S3 Standby
IfS3Standbystateisdesired,therearecertainrestrictionswithconnectingtheMSRto
a7409terminal.
Restrictions on 7409 USB Ports:
If a Restricted Device is
plugged into Port: An S3 Wake Device can NOT be plugged into Port:
AB
BA
CD
DC
EF
FE
Note: TherestrictionsonlyapplyifitisdesiredtoputtheunitinS3standbystate.
USB Devices Capable of Waking the 7409 from an S3 State
•USBKeyboard
•USBMouse
Reasons for the Restrictions
•USBportsshareUHCIhostcontrollersintheSouthbridge.
•AllexternalUSBportsonthe7409arepoweredby5VSBandkeptONduringS3
Standby.
•SomeUSBperipheralsarepoweredbytheRS‐232port(either5Vor12V).
Ways Around the Issue
•AdheretotheRestrictionGuidelinesprovidedabove.
•InWindows,disabletheS3WakeDevice’sabilitytowaketheunitfromStandby.
•PowertheRestrictedDevicesfromanexternalpowersourceinsteadoftheRS‐232
ports.