NCR VOYIX CX7 Manual

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited
7772-K030
Issue C
Stand, CX7
Kit Instructions

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
2
Copyright
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR CX7 All-in-One POS (7772) is a trademark of NCR
Corporation in the United States and/or other countries. Other product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Java is a registered trademark of Oracle and/or its affiliates.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under
the terms and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware
become available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some
instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR
representative or NCR office for information that is applicable and current.
Copyright © 2021–2024
By NCRCorporation
Global Headquarters
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
3
Table of Contents
Copyright 2
Stand, CX7 5
Kit Contents 5
Installation Procedure 7
Installing the Stand 7
Installing the Integrated Power Supply 10
Changing the Neck Covers 16

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
4
Revision Record
Issue Date Remarks
A Sep 2021 First Issue
B Dec 2021 Added Warning statement
C Jan 2022 Updated routing for Power Supply Cable

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
5
Stand, CX7
This kit provides a Stand for the NCR CX7 All-in-One POS (7772) or NCRCX5 All-in-One
POS(7773).
Kit Contents

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
6
Item Part Number Description
1Stand Assembly
497-0523815 Base, HSG, Cast, Silver
497-0523819 Neck, Center, Cast, Silver
497-0523775 Base, Trim, Bottom, Blk7
497-0523779 Base, Foot,Center, Blk7
497-0524135 Base Feet, CX7, Blk7
497-0528039 Hinge, CX, Blk7
497-0523767 Base, Cover, Top, Remote Power Supply, Blk7
497-0531326 Mounting Plate – VESA, CX7, Blk7
497-0531317 Cover – Neck, CX7, Blk7 (Neck Cover)
497-0531321 Door – Neck, CX7, Blk7 (Neck Door)
006-0654018 Screw, Metric, SEMS, Phillips, Pan Head,M4x10, 10mm length
006-8612048 Screw, M3x8, SEMS, Phillips, Pan Head, Steel, Z
006-8622885 Screw, M4–0.7 x 8mm Flat Head, Machine, Knurled Head, Steel,
Black Oxide
006-8624893 Screw, M3x5, Steel, Flat Head, Phillips, Clear Zinc, w/ NDNylon
Patch
006-8625003 Screw, SEMS, M4x14, Pan Head, Phillips
006-8626665 Screw, M3x14mm, SEMS, Steel, Phillips, Pan Head, Zinc
006-8628206 Male–Female Threaded Hex Standoff, Steel, Zinc Plated, 16mm long,
M4 x 0.70mm size, w/ NDMicrospheres Thread Lock
2 006-8622885 Screw, M4–0.7 x 8mm Flat Head, Machine, Knurled Head, Steel,
Black Oxide

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
7
Item Part Number Description
3 497-0523791 Neck, Inner, Black (Front Neck Cover)
4 497-0523787 Neck, Outer, Black (Back Neck Cover)
5 006-8627391 Screw, M3x16, Flat Head, Black
6 497-0523771 Base, Cover, IntegratedPower Supply, Blk7
Installation Procedure
Installing the Stand
Warning
Disconnect the AC power cord from the AC outlet and wait 30 seconds before
servicing the terminal.
1. Install the CX7 with Integrated I/O on the Bracket (4 screws).
Note
For clarity, the Neck Cover is not shown in the illustration.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
8
2. Remove the Neck Door.
a. Loosen the two (2) thumbscrews on the Neck Door.
b. Rotate the Door forward and pull out to remove.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
9
3. Connect the Cables to the I/O.
4. Route the Cables down the Neck as shown.
5. Reinstall the Neck Door.
a. Hook the Neck Door on the Neck Cover. Position the Door so that the door
standoffs (one on each side) sit on the hooks on the inside of the neck cover
(one on each side).

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
10
b. Tighten the two (2) thumbscrews.
Installing the Integrated Power Supply
Warning
Disconnect the AC power cord from the AC outlet and wait 30 seconds before
servicing the terminal.
1. Remove the Neck Door.
a. Loosen the two (2) thumbscrews on the Neck Door.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
11
b. Rotate the Door forward and pull out to remove.
2. Slightly push the front side of the Base Cover, then pivot the cover open.
3. Route the ACCord up through the opening in the Base.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
12
4. Position the Power Supply in the recess on the Base.
Note
The Power Supply Cable comes bundled as shown.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
13
5. Set the Ferrite Bead in the small recess on the Base and secure the Cable under the
Cable Management Hook.
6. Route the Power Supply Cable.
a. Insert the DCConnector of the the Power Supply Cable down through the
Base opening.
b. On the underside of the Base, pull the DCConnector such that the excess
cable is under the Base.
7. Connect the ACCord to the Power Supply.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
14
8. Hook the Base Cover into the Stand, then snap into place.
9. Route the Power Supply Cable up along the Neck as shown and insert the
DCConnector into the Power In connector on the Integrated I/O.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
15
10. Reinstall the Neck Door.
a. Hook the Neck Door on the Neck Cover. Position the Door so that the door
standoffs (one on each side) sit on the hooks on the inside of the neck cover
(one on each side).
b. Tighten the two (2) thumbscrews.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
16
Changing the Neck Covers
The kit includes an assembled stand with a wide neck cover and door to allow cable
management. The neck covers can be changed to the standard front neck cover (497-
0523791) and back neck cover (497-0523787), which are also included in the kit.
1. Remove the Neck Door.
a. Loosen the two (2) thumbscrews on the Neck Door.
b. Rotate the Door forward and pull out to remove.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
17
2. Remove the Base Rear Foot (2 screws).
3. Remove the Neck Cover.
a. Remove the two (2)Hex Standoffs from the Neck.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
18
b. Remove the two (2)screws that secure the Neck Cover to the Neck.
c. Remove the Neck Cover.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
19
4. Snap the Back Neck Cover onto the neck. The Cover has a simple snap fit
connection at the top.
5. Install the Base Rear Foot (2 screws). Ensure the Neck Cover is captured under the
Base Rear Foot.
Note
The Base Rear Foot serves to manage the cables and hold the bottom of the
Neck Cover in place.

Confidential and proprietary information of NCRCorporation.
Unauthorized use, reproduction and/or distribution is strictly prohibited.
20
6. Attach the Front Neck Cover to the Neck.
7. Secure the Front Neck Cover to the Neck with two (2) screws. Use the appropriate
screws:
lflat head screws for Base without Integrated Power Supply
lthumbscrews for Base with Integrated Power Supply